Related Manuals for HotDog WC52-VET
Summary of Contents for HotDog WC52-VET
- Page 1 Veterinary Patient Warming System Controller Model WC52-VET User Manual Manufactured by: Augustine Temperature Management 6581 City West Parkway Eden Prairie, MN 55344 USA TEL 952.465.3500 FAX 952.465.3501 www.hotdogwarming.com...
-
Page 2: Table Of Contents
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 2 Contents Introduction ............................. 3 Device Description ........................3 Indications for Use ........................3 Contraindications ......................... 3 Warnings ............................4 Ensure that adequate steps are taken to mitigate pressure............... 5 Proper Use and Maintenance ...................... -
Page 3: Introduction
The Hot Dog Veterinary Patient Warming System (“System”) consists of the Hot Dog Controller, reusable Warming Blankets. This manual includes use and maintenance instructions and specifications for the Hot Dog Controller Model WC52-VET. For information about Hot Dog warming blankets, refer to the User Manual provided with each blanket. -
Page 4: Warnings
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 4 WARNINGS General • EXPLOSION HAZARD – DO NOT use the Hot Dog Patient Warming System in the presence of flammable anesthetics or highly oxygen-enriched environments such as hyperbaric chambers, oxygen tents, etc. •... -
Page 5: Ensure That Adequate Steps Are Taken To Mitigate Pressure
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 5 Use over-body warming instead of under-body warming on patients with multiple risk factors such as short hair, poor circulation, severe illness that may impact circulation, or long-duration procedures (> 2 hours). Do not expose the Hot Dog Warming Blanket to a continuous exchange of cold irrigation fluids. -
Page 6: Initial Setup & Assembly
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 6 INITIAL SETUP & ASSEMBLY Contents The following components are included in the Hot Dog Controller box: • 1—Hot Dog Controller Model WC5X • 1—IV pole adapter and mounting hardware •... -
Page 7: Control Panel Features & Operating Modes
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 7 Control Panel Features & Operating Modes Figure 2: Hot Dog Model WC5X Controls Figure 3: Hot Dog Ports... -
Page 8: Alarms
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 8 Mains Power Switch / ON Power Indicator When the Hot Dog Controller is plugged into an electrical outlet and the Mains Power Switch on the back of the Controller is turned ON, all displays will illuminate briefly, and the Controller will beep. -
Page 9: Error Codes
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 9 Yellow. The Controller will automatically turn off power to that warming device. If the Alarm Light stays illuminated and the alarm continues to sound, disconnect the warming device from the Controller to silence the alarm. -
Page 10: Instructions For Use
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 10 INSTRUCTIONS FOR USE The instructions below describe how to operate the Model WC5X Hot Dog Controller. For information about Hot Dog warming blankets, refer to the User Manual provided with each blanket. -
Page 11: Cleaning-General
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 11 Method 1. Insert the Hot Dog Controller’s power plug into a properly grounded hospital-grade electrical outlet and confirm that NO cables or blankets are connected to any of the Controller’s ports. 2. -
Page 12: Cleaning-Hot Dog Controller
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 12 Cleaning—Hot Dog Controller Frequency As needed Tools/Equipment • Sponge or soft cloth • Mild detergent or anti-microbial spray • Dry soft cloth Method 1. Disconnect the Controller from the power source before cleaning. 2. -
Page 13: Troubleshooting/Error Codes
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 13 TROUBLESHOOTING/ERROR CODES Alarm lights and error code display Alarm lights and an audible alarm turn on when an error condition occurs. The associated error code will remain on the display until the condition is cleared. If multiple alarm conditions occur sequentially, the code associated with the initial alarm condition will be displayed. -
Page 14: Technical Support & Customer Service
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 14 System failure. If this occurs, call customer service for technical support Calibration failure EA, EA, EA System failure. If this occurs, call customer service for technical support Hardware CPLD failure EC, EC, EC System failure. -
Page 15: Definition Of Product Symbols
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 15 DEFINITION OF PRODUCT SYMBOLS Mains Power On Do Not Place Under Patient This Side Up Indicator This Side Down Heating Area Alarm Attention, consult Reference Number Lot Number accompanying documents BF Patient Applied Part Serial Number Manufacture Date... -
Page 16: Specifications
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 16 SPECIFICATIONS Physical Characteristics Dimensions 33 cm high x 14.0 cm deep x 19.7 cm wide13” high x 5.5” deep x 7.75” wide Weight 5 kg (11 lbs.) Mounting Can be placed on a horizontal flat surface (i.e. table top), clamped to an IV pole or hung on a OR/gurney rail using optional hanging hooks Temperature Characteristics Temperature Control... - Page 17 User Manual: Hot Dog Veterinary Patient Warming System Controller Page 17 Electrical Characteristics Leakage Current Meets UL 2601-1 and IEC 60601-1 requirements for Class I, Type BF equipment. Power Consumption 850W maximum Power Cord 4.6 m (15 ft) Device Ratings Input: 100-240 VAC, 50/60 Hz, 850VA Output A &...
-
Page 18: Electromagnetic Compatibility (Emc)
User Manual: Hot Dog Veterinary Patient Warming System Controller Page 18 ELECTROMAGNETIC COMPATIBILITY (EMC) The Hot Dog Vet Patient Warming System requires special precautions regarding EMC and must be installed and put into service according to the EMC information provided in this User Manual. Warning •... - Page 19 User Manual: Hot Dog Veterinary Patient Warming System Controller Page 19 Guidance and Manufacturer’s Declaration – Electromagnetic Immunity The Hot Dog™ Vet Patient Warming System is intended for use in the electromagnetic environment specified below. The customer or the user of the Hot Dog Patient Warming System should assure that it is used in such an environment.
- Page 20 User Manual: Hot Dog Veterinary Patient Warming System Controller Page 20 Guidance and Manufacturer’s Declaration – Electromagnetic Immunity (cont’d) The Hot Dog™ Vet Patient Warming System is intended for use in the electromagnetic environment specified below. The customer or the user of the Hot Dog Vet Patient Warming System should assure that it is used in such an environment.
- Page 21 User Manual: Hot Dog Veterinary Patient Warming System Controller Page 21 Recommended separation distances between portable and mobile RF communications equipment and the Hot Dog Patient Warming System The Hot Dog Vet Patient Warming System is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
Need help?
Do you have a question about the WC52-VET and is the answer not in the manual?
Questions and answers