Step 2: Connecting To Your Audio Component; Step 4: Preparing The Remote; Controlling Tvs With The Remote; Step 5: Quick Setup - Sony DVP-NS611HP Service Manual

Step 2: Connecting to Your Audio Component

Select one of the following patterns A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver).
This will enable you to listen to sound.
(red)
Audio/video
cable (supplied)
(white)
(yellow)*
to LINE OUT L/R (AUDIO)
to DIGITAL OUT
(COAXIAL)/HDMI OUT
or
HDMI cord (supplied with
DVP-NS710HP, DVP-NS718HP,
and DVP-NS728HP only)
[Speakers]
Rear (L)
Front (L)
Audio component
with a decoder
Centre
: Signal flow
* The yellow plug is used for video signals (page 10).
z
For correct speaker location, see the operating instructions supplied with the connected components.
12

Controlling TVs with the remote

You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
Available buttons
Depending on the connected unit, you may
not be able to control your TV using all or
some of the buttons on the supplied remote.
Buttons Operations
TV [/1
Turn the TV on or off
2/VOL (volume)
Adjust the volume of the
+/– TV
TV /TV INPUT Switch the TV's input
(input select) source between the TV and
other input sources
To control other TVs with the remote
You can control the volume, input source, and
power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer's code.
b
When you replace the batteries of the remote, the
code number may be reset to the default setting. Set
the appropriate code number again.
1 While holding down TV [/1, press the
number buttons to select your TV's
manufacturer's code.
2 Release TV [/1.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
14
DVP-NS611HP/NS710H/NS710HP/NS717HP/NS718H/NS718HP/NS728H/NS728HP
A
(yellow)*
INPUT
VIDEO
(white)
L
(red)
AUDIO
R
TV, projector, or
audio component
CD/DVD player
Coaxial digital cord
(not supplied)
to coaxial/HDMI
B
digital input
[Speakers]
Rear (R)
Front (R)
Subwoofer
◆ For RMT-D187P/RMT-D189P remote
commander only
Manufacturer Code number
Sony 01 (default)
Hitachi 24
JVC 33
LG/Goldstar 76
Panasonic 17, 49
Philips 06, 08, 72
Samsung 71
Sharp 29
Toshiba 38
◆ For RMT-D187A/RMT-D189A remote
commander only
Manufacturer Code number
Sony 01 (default)
Hitachi 02
LG/Goldstar/NEC 04
MGA/Mitsubishi 13
Panasonic 19
Philips 21
Pioneer 16
RCA 10
Samsung 20
Sharp 18
Toshiba 07
A
Audio L/R input jacks
This connection will use your TV's or audio
component's two speakers for sound.
B
Digital audio input jack
1
If your audio component has a Dolby*
2
Digital, DTS* , or MPEG audio decoder and
a digital input jack, use this connection. You
can enjoy Dolby Digital (5.1ch), DTS
(5.1ch), and MPEG audio (5.1ch) surround
effect.
If you connect to a Sony audio component
that is compatible with the CONTROL FOR
HDMI function, refer to the operating
instructions supplied with the audio
component.
*1
Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
*2
Manufactured under license under U.S. Patent #:
5,451,942 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital Out are
registered trademarks and the DTS logos and
Symbol are trademarks of DTS, Inc. © 1996-
2008 DTS, Inc. All Rights Reserved.
b
• After you have completed the connection, make
the appropriate settings in Quick Setup (page 15).
If your audio component has an MPEG audio
decoder function, set "MPEG" to "MPEG" in
"AUDIO SETUP" (page 37). Otherwise, no
sound or a loud noise will come from your
speakers.
• The TVS effects of this player cannot be used
with this connection.
• When you connect the player to an audio
component using an HDMI cord, you will need to
do one of the following:
– Connect the audio component to the TV with the
HDMI cord.
– Connect the player to the TV with a video cord
other than HDMI cord (component video cord or
audio/video cord).
• When connecting to the HDMI OUT jack,
carefully align the HDMI connector with the jack.
Do not bend and apply force to the HDMI cord.

Step 5: Quick Setup

Follow the steps below to make the minimum
number of basic adjustments for using the
player.
To skip an adjustment, press >. To return
to the previous adjustment, press .. The
on-screen displays differ depending on the
player model. Oceanian model is used for
illustration unless otherwise specified.
1
Turn on the TV then press [/1.
2
Switch the input selector on your
TV so that the signal from the
player appears on your TV screen.
"Press [ENTER] to run QUICK SETUP"
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
"QUICK" (quick) under "SETUP"
(setup) in the Control Menu to run Quick
Setup (page 20).
3
Press ENTER without inserting a
disc.
The Language Setup Display appears.
The available languages differ depending
upon the player model.
LANGUAGE SETUP
OSD: ENGLISH
MENU:
ENGLISH
AUDIO:
FRANÇAIS
SUBTITLE:
DEUTSCH
ITALIANO
ESPAÑOL
NEDERLANDS
DANSK
SVENSKA
4
Press X/x to select a language.
The player displays the menu and
subtitles in the selected language.
5
Press ENTER.
The Screen Setup Display appears.
1-3
Step 3: Connecting the
Mains Lead
Plug the player and TV mains lead (power
cord) into a mains.
Step 4: Preparing the
Remote
Insert two R6 (size AA) batteries by matching
the 3 and # ends on the batteries to the
markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
b
• Do not leave the remote in an extremely hot or
humid place.
• Do not drop any foreign object into the remote
casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light
from the sun or a lighting apparatus. Doing so
may cause a malfunction.
• If you do not use the remote for an extended
period of time, remove the batteries to avoid
possible damage from battery leakage and
corrosion.
,continued
13
SCREEN SETUP
TV TYPE: 16:9
COLOR SYSTEM (VIDEO CD): 16:9
4:3 LETTER BOX
SCREEN SAVER:
BACKGROUND: 4:3 PAN SCAN
PROGRESSIVE : OFF
(COMPONENT OUT ONLY)
MODE : AUTO
(PROGRESSIVE)
4:3 OUTPUT: FULL
6
Press X/x to select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 33)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 33)
7
Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component appears.
Is this player connected to an amplifier
(receiver) ? Select the type of jack you
are using.
YES
LINE OUTPUT L/R (AUDIO)
DIGITAL OUTPUT
NO
8
Press X/x to select the type of jack
(if any) you are using to connect to
an audio component, then press
ENTER.
Select "NO," if you do not connect an
audio component, then go to step 12.
Select "YES: LINE OUTPUT L/R
(AUDIO)," if you connect an audio
component using an audio cable, then go
to step 12.
Select "YES: DIGITAL OUTPUT," if
you connect an audio component using a
digital coaxial cable/HDMI cord.
,continued
15