Table of Contents
Advertisement
SA-PM91DEE
14.5. Self-Diagnosis Error Code Description
Code Display
F61
Abnormal output or power supply
H15
OPEN SW
H16
CLOSE SW
CD F28
The DISC loading is abnormal
CD F29
The DISC unloading is abnormal
CD F27
DOWN SW is abnormal
CD F22
Mechanism is loading motor/abnormal
14.6. DVD/CD Self-Diagnosis Error Code Description
Abnormal display
U11
H01
H02
H03
H04
H05
F010
F020
F021
F022
F023
F024
F030
F031
F040
F041
F042
F043
F050
F051
F052
F053
F060
F061
F062
F063
F064
F065
F066
F067
F070
F080
F0E0
F0E1
F0E2
F0E3
F0E4
F0E5
F0E6
F0F0
F0F1
F103
F4FF
F500
F501
F502
F503
F504
F505
Abnormal Item
Focus servo failure
Tray loading failure
Spindle servo failure
Traverse motor failure
Tracking servo error
Seek timeout failure
A specified value is larger than the Parental value of a specified country.
There is no TT_SRPT. (RLBN is 0.)
The number of TT_SRP is 0.
A specified value is larger than the number of TT_SRP.
There is no SRP corresponding to VTSN or VTS_TTN.
A specified value is larger than TT_SRP.PTT_Ns.
The number of TTU_SRP is 0.
A specified value is larger than the number of TTU_SRP.
SRP1 or more is 0.
The number of PGCI_SRP is 0.
A specified value is larger than the number of PGCI_SRP.
There is no PGCI_SRP corresponding to Menu ID.
The number of TMAP_SRP is 0.
A specified value is larger than the number of TMAP_SRP.
Specification TMAP_SA is 0.
The number of MAP_EN is 0.
There is no PGMAP in PGC though C_POSIT exists.
The number of PG in PGC is 0 though C_POSIT exists.
A specified value is larger than the number of PG in PGC.
There is no C_PBIT in PGC though C_POSIT exists.
The number of PG in PGC is 0 though C_POSIT exists.
Specification Cell number is 0.
A specified value is larger than the number of Cell in PGC.
It should be a block cell.
It is not NV_PCK data.
There is no Cell number under the retrieval.
The PGC control file for the guide of the user ..DFD.. cannot be eliminated.
There is no DFD interchangeable type with DFD main microcomputer. It is not possible to download it.
DFD starting download PGC reproduction error
DFD download completion waiting PGC reproduction error
AVDEC when DFD is downloaded
Farm file lead error when DFD is downloaded
Falsification check error of firmware that reads DFD
There is no farm file and it downloads it DFD unnecessary.
There is no firmware corresponding to the DFD download condition and it is unnecessary.
Illegal Highlight Position
There was no ACK though the compulsion initialization demand was done to Panecon.
DSC Error
DSC Not Ready Error
DSC Time Out Error
DSC Communication Failure
The DSC data slice offset adjustment is abnormal.
DSC Attention Error
When DCDET becomes L while operating, PCONT is set to L
without usual POWER OFF processing, and F61 is displayed after
GOOD-BYE
display.
memorized and displayed in the abnormal detection display mode.
It is memorized if there is abnormal SW while operation, and is fail-
save operation, and an abnormal content is displayed by the self-
diagnostic mode usually.
Abnormal SW is detected in the abnormal detection mode.
Memory when switch is not changed even if it exceeds it to time of
fail safe time when horizontally operating toward PLAY position
doesn't enter state of target.
When mechanism begins to operate next time, initialization is done.
Only when backup data is cleared clearly of this error No. when it
compels clearly or power supply start-up.
The error is detailed
58
Detection Method
Occurrence
of
abnormality
shall
be
Advertisement
Table of Contents
