Advertisement
Table of Contents
MR16out PROCESSOR
Installation and Specifications:
1. General:
The MR16out processor provides a solution to the OEM system integrator for output control.
controller has 16 form-C contact relays for load switching. Additionally, 2 digital inputs are provided for
tamper and power fault status monitoring. The processor requires 12 to 24Vdc for power.
OUTPUTS
TAMPER AND POWER
MONIOTR INPUTS
SIO COMMUNICATION
PORT, RS-485
POWER IN
12-24Vdc
2. Supplying Power to the MR16out:
The MR16out requires 12 to 24Vdc for power on TB11.
source as close to the unit as possible. Connect power with minimum of
18AWG wires.
Observe POLARITY on VIN!
Mercury Security Corporation © 2009
2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562)986-9105 FAX (562) 986-9205
.25 [6.35]
1
2
NO
C
NC
OUT 1
NO
C
NC
K2
OUT 2
NO
K4
C
NC
OUT 3
NO
OUT 4
C
NC
K6
NO
C
NC
OUT 5
NO
C
NC
OUT 6
NO
C
NC
OUT 7
NO
C
NC
OUT 8
CT
BA
GND
TR+
TR-
R+
R-
J1, J2
GND
RS-485
TERM
VIN
GND
.50 [12.70]
MR16out
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
RELAY STATUS LEDs
6.00 [152.40]
5.50 [139.70]
3
4
5
6
7
8
9
10 11
12
13 14
15
16
K9
K1
K10
K11
K3
K12
K5
K13
K14
J6
J5
J7
U1
2W
4W
J3
J8
J4
Locate power
DOC 10107-0012
REV 2.01
www.mercury-security.com
The
NC
C
NO
OUT 9
NC
OUTPUTS
C
NO
OUT 10
NC
C
NO
OUT 11
NC
OUT 12
C
NO
NC
C
NO
OUT 13
NC
C
NO
OUT 14
NC
C
NO
OUT 115
NC
C
STATUS LEDs
NO
OUT 16
A
B
CT
BA
DIP SWITCHES
S1
1
2
3
4
Ø.156 [Ø4.0]
5
6
7
8 PLACES
8
+
VIN
12 TO 24Vdc
-
GND
Page 1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Mercury Security MR16out
Summary of Contents for Mercury Security MR16out
- Page 1 Installation and Specifications: 1. General: The MR16out processor provides a solution to the OEM system integrator for output control. controller has 16 form-C contact relays for load switching. Additionally, 2 digital inputs are provided for tamper and power fault status monitoring. The processor requires 12 to 24Vdc for power.
-
Page 2: Communication Wiring
3. Communication Wiring: The MR16out communicates to a controller via a 2-wire RS-485 interface. The interface allows multi-drop communication on a single bus of up to 4,000 feet (1,200 m). Use twisted pair (minimum 24 AWG) with shield for the communication line. - Page 3 See note 2 below. Note 1: Firmware revisions prior to 1.30.1, this setting is 2,400 BPS. Note 2: Firmware revisions prior to 1.30.1, SW8 is not defined. Set to the OFF position. Mercury Security Corporation © 2009 MR16out DOC 10107-0010 REV 2.01...
-
Page 4: Status Leds
Indicates communication activity on the SIO communication port CT: Cabinet Tamper BA: Power Fault LED 1 through 16: Illuminates when output relay OUT 1 (K1), OUT 2 (K2) is energized and so on. Mercury Security Corporation © 2009 MR16out DOC 10107-0010 REV 2.01... -
Page 5: Specifications
There are no expressed warranties other than set forth herein. Mercury Security Corporation does not make, nor intends, nor does it authorize any agent or representative to make any other warranties, or implied warranties, and expressly excludes and disclaims all implied warranties of merchantability or fitness for a particular purpose.
Need help?
Do you have a question about the MR16out and is the answer not in the manual?
Questions and answers