Safety Information DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the devices that attach to the system. It is the responsibility of the customer to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged.
Page 8
Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
Handling Static-Sensitive Devices Attention: Static electricity can damage this device and your system unit. To avoid damage, keep this device in its antistatic protective bag until you are ready to install it. To reduce the possibility of electrostatic discharge, follow the precautions listed below: v Limit your movement.
Page 10
viii Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
About This Book This book provides information about the Gigabit Ethernet-SX PCI-X Adapter and Dual Port Gigabit Ethernet-SX PCI-X Adapter, how to install and configure the adapter, and how to attach the adapter to a network. Use this book together with your specific system unit and operating system documentation.
Page 12
Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
Chapter 1. Overview The Gigabit Ethernet-SX PCI-X Adapter and Dual Port Gigabit Ethernet-SX PCI-X Adapter are high-performance, highly integrated, universal, Ethernet LAN adapters for PCI-X and PCI systems. The adapters provide 1000 Mbps throughput on a standard shortwave (850 nm) 50/62.5 micron multimode optical cable and conform to the IEEE 802.3z standards and support distances of 260 meters for 62.5u...
(See Chapter 3, “Installing the Device Driver Software,” on page 5 for instructions.) Verifying Your Hardware Requirements The Gigabit Ethernet-SX PCI-X Adapter and Dual Port Gigabit Ethernet-SX PCI-X Adapter require the following hardware: v A wrap plug for the multimode fiber connector, if you are running the total diagnostics package v Shortwave (850 nm) 50/62.5 micron multimode fiber network attachment...
If an item is missing or damaged, contact the place of purchase. Note: Be sure to retain your proof of purchase as it might be required to receive warranty service. Gathering Tools and Documentation To install the adapter, you need the following items: A flat-blade screwdriver Your system unit documentation, including any service manual Your operating system documentation...
Chapter 3. Installing the Device Driver Software This chapter explains how to install the device driver for the Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters on an AIX system. The device driver is provided for the AIX operating system.
13. When RUNNING changes to OK, scroll down to the bottom of the panel and locate the Installation Summary. If the installation was successful, SUCCESS appears at the bottom of the panel in the Result column of the Installation Summary. 14.
Page 19
Fileset Level State Description ----------------------------------------------------------------------- Path: /usr/lib/objrepos devices.pci.14108802.rte 5.1.0 COMMITTED ...Ethernet... Adapter Software Path: /etc/objrepos 5.1.0 devices.pci.14108802.rte COMMITTED ...Ethernet... Adapter Software Verify that the devices.pci.14108802.rte filesets are installed at the AIX 5L for POWER version 5.1.0 with the 5100-04 Recommended Maintenance package (APAR IY36771) level or later. If this information displays but you continue to have problems, go to Chapter 4, “Installing the Gigabit Ethernet-SX PCI-X Adapter or Dual Port Gigabit Ethernet-SX PCI-X Adapter,”...
Page 20
Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
Chapter 4. Installing the Gigabit Ethernet-SX PCI-X Adapter or Dual Port Gigabit Ethernet-SX PCI-X Adapter After you install the appropriate device driver, you can install the Gigabit Ethernet-SX PCI-X Adapter or Dual Port Gigabit Ethernet-SX PCI-X Adapter. This chapter takes you through the steps of installing your adapter, which involves the following tasks: v Installing the adapter v Verifying the adapter installation...
If the message on your screen indicates your adapter is DEFINED instead of AVAILABLE, shut down your machine. Verify that the adapter was installed correctly. Go to “Installing the Adapter” on page 9 and return to this section and repeat the verification steps. Note: If the message on your screen indicates your adapter is DEFINED a second time, it may be necessary to contact your service representative.
Chapter 5. Connecting to an Ethernet Network This chapter explains how to connect the adapter to the multimode fiber network. Refer to your local procedures for information about connecting the Gigabit Ethernet-SX PCI-X Adapter or Dual Port Gigabit Ethernet-SX PCI-X Adapter to your Ethernet network. Note: Only one type of network can be attached to the adapter card at one time.
Understanding the Adapter LED The LED on the Gigabit Ethernet-SX PCI-X Adapter and Dual Port Gigabit Ethernet-SX PCI-X Adapter provides information about the card’s operation status. The LED is visible through the card’s mounting bracket and, when lit, indicates the following conditions:...
Appendix A. Communications Statements The following statement applies to this product. The statement for other products intended for use with this product appears in their accompanying documentation. Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 / European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices.
Radio Protection for Germany Dieses Gerät ist berechtigt in Übereinstimmung mit dem deutschen EMVG vom 9.Nov.92 das EG–Konformitätszeichen zu führen. Der Aussteller der Konformitätserklärung ist die IBM Germany. Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse B. Appendix A. Communications Statements...
Page 28
Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
Appendix B. Notices This information was developed for products and services offered in the U.S.A. The manufacturer may not offer the products, services, or features discussed in this document in other countries. Consult the manufacturer’s representative for information on the products and services currently available in your area.
Page 30
Gigabit Ethernet-SX PCI-X and Dual Port Gigabit Ethernet-SX PCI-X Adapters Installation and Using Guide...
Page 32
Part Number: 80P3146 Printed in USA SA23-1302-02...