Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stark U-AURA Series
Summary of Contents for Stark U-AURA Series
- Page 1 Original Operating and maintenance manual Bucket spreader...
-
Page 2: General
For us, the long lifecycle and efficiency of your new equipment is a priority. To keep the bucket spreader in top working condition, read this manual carefully before using the equipment. STARK products are engineered and manufactured in Finland, and each of them is equipped according to the needs of the customer. -
Page 3: Table Of Contents
Table of contents General ..............................2 Read before use ........................... 2 1. DECLARATION OF CONFORMITY ...................... 4 2. PURPOSE OF USE ..........................5 3. SAFETY PRECAUTIONS ........................5 4. IDENTIFICATION INFORMATION AND SPAREPARTS ................ 6 4.1. Identification plate ..........................6 4.2. -
Page 4: Declaration Of Conformity
1. DECLARATION OF CONFORMITY The original manufacturer’s EC declaration of conformity: Generic product name: Bucket spreader Models: HK 310, HK 360, HK 400, HK460, HK 560, HK 710, HK 1010, HK 1400, HK 1800, HK 2200, HK 2600, HK 3010 Manufacturer: Lametal Oy Kaskenviertäjäntie 2 73100 LAPINLAHTI, Finland... -
Page 5: Purpose Of Use
2. PURPOSE OF USE The Bucket spreader is used for sanding streets and small / large areas. 3. SAFETY PRECAUTIONS Make sure you know your equipment before you start using it. Equipment may be operated only by an individual who is thoroughly familiar with its use. Before connecting hydraulics to the base machine, make sure that: there is no-one between the attachment and the base machine the base machine is turned off and the parking brake is on. -
Page 6: Identification Information And Spareparts
(marked in the identification plate) when you order spare parts. For more information on maintenance and spare parts, please contact the STARK maintenance and spare part services or your retailer. -
Page 7: Main Parts Of The Bucket Spreader
5. MAIN PARTS OF THE BUCKET SPREADER Picture 2. Main parts of the bucket spreader 1) Frame of the bucket spreader 2) Spreader roll 3) Mixing shaft 4) Engine’s case 5) Hydraulic engine 6) Flow control valve Sivu 7 / 17... -
Page 8: Attaching The Bucket Spreader
6.1. Attaching the bucket spreader to a base machine The bucket spreader is attached to the base machine by welded or bolted STARK FIT quick hitches. The machine is connected to a hydraulic system. Hydraulic circuit diagrams can be found in a later section in this manual. Ask your retailer for available STARK FIT quick hitches. -
Page 9: Operating The Bucket Spreader
7. OPERATING THE BUCKET SPREADER Before using the bucket spreader, make sure: the bucket spreader is installed correctly all locking pins are in place hydraulic hoses are connected properly hoses are intact there are no oil leaks all functions are working properly 7.1. -
Page 10: Adjusting The Sanding Roller Rubber
7.2. Adjusting the sanding roller rubber The sanding roller rubber is a wear part. Make sure to check its condition and tightness before the winter season. Adjusting of the sanding roller rubber: loosen the fixing bolts of the protective plates, push the rubber out of the opening (e.g. -
Page 11: Adjusting The Chain
7.3. Adjusting the chain The spreader roll and the mixing shaft are operated by a hydraulic engine chain. The chain needs to be checked for tightness every 50 hours of operation to make sure that the bucket spreader works properly. Remove the protective cap and press the chain e.g. -
Page 12: Detaching The Bucket Spreader
7.4. Detaching the bucket spreader 1. Lower the bucket spreader to an even ground. 2. Turn off the base machine, put on the parking brake and release pressure from the system 3. Detach the hydraulic hoses and protect the couplings with plugs 4. -
Page 13: Maintaining The Bucket Spreader
8. MAINTAINING THE BUCKET SPREADER 8.1. General safety precautions for use and maintenance Comply with the applicable laws and regulations and the instructions in this manual. Never go under the bucket spreader if it is not supported. Always put on the base machine’s parking brake before any servicing on the attachment. Use only tools which are in good condition. -
Page 14: Lubrication Points
8.6. Lubrication points 1) Grease nipples of the bearings 2) Grease nipples of the bearings and of the chain Picture 5. Grease nipples of the bearings Picture 6. Grease nipples of the bearings and of the chain Sivu 14 / 17... -
Page 15: Hydraulics
Max. allowed oil flow is 120l / min. A larger flow controller is required for higher oil flow from the base machine. Please contact STARK spare parts sales! Due to counter pressure in the return line, some oil may leak in the Bucket spreader motor housing (this may damage the engine sealing). - Page 16 Picture 3. Drain line greasing nipple at the end of the motor housing Chart 2. The counter pressure of the returning oil Sivu 16 / 17...
-
Page 17: Warranty Policy
3. Warranty period STARK warranty covers a period of one (1) year. If need be, the client and the manufacturer make separate agreements on warranty concerning repairs and spare parts used in repairs. 4. Repairs during the warranty period Repairs during the warranty period are carried out free of charge within the normal working hours by the manufacturer repair and maintenance services or by a repair service provider accredited by the manufacturer.
Need help?
Do you have a question about the U-AURA Series and is the answer not in the manual?
Questions and answers