General Information - Novy 1801 One Power Mounting Instructions

EN

1. GENERAL INFORMATION

1.1 General
These are the mounting instructions for the Novy unit
shown on the cover. The user manual is delivered sep-
arately with this unit. Carefully read these instructions
before installing and commissioning this unit.
This manual makes use of a number of symbols. The
meaning of these symbols are given below.
Symbol Meaning

Read

Warning
Follow this instruction to avoid injury and material damage.
1.2 Safety
Observe the following mounting and safety tips for
mounting:
− The installation and electrical connection of the unit
shall be carried out by an authorised expert. The manu-
facturer does not accept any responsibility for any
damage resulting from faulty building in or connection.
− Carefully take the unit from the packaging and check
it for damage before mounting. Do not mount the unit
in case of any damage.
− Check if all mounting materials have been supplied
using the drawings in section 2.2.
− The unit is intended for household use only (preparation
of food) excluding any other domestic, commercial or
industrial use.
− Position the electrical connection such, that it is located
in the cabinet in which the cooking unit is mounted.
− Safety can only be guaranteed if the unit is connect-
ed to an earth wire in accordance with the required
regulations.
− Do not use an extension cord for connecting to the
electricity grid.
− A damaged cooking plate can endanger your safety.
Check the cooking plate for visible damage. Do not
mount a damaged cooking, but contact your supplier.
− Do not modify or change the unit.
− Do not use the cooking plate as a basis or work surface.
− For the users of pacemaker, the magnetic field could
influence its operating. We recommend getting infor-
mation to the retailer or of the doctor.
1.3 Exhaust or recirculation
Before mounting, the choice is to be made between an
exhaust duct to the outside or recirculation. The unit is
supplied by default with settings for recirculation.
Chapter 3 includes an extensive explanation of the
conditions for both systems.
Action
Carefully read the instruc-
tions
This symbol indicates a
dangerous situation.
2. INSTALLATION
Before installation read the general information and safety
regulations (see chapter 1). Mounting shall only be carried
out by authorised experts. The user has to observe the
laws and standards of the country of residence.
2.1 Installation regulations

The distance between the cooking plate
and the wall must be min. 55 mm.
− The cooking plate belongs to protection class « Y ».
When built in, there may be a high cabinet side or a
wall on one side and at the rear. On the other side
there may be no piece of furniture or unit higher than
the cooking surface.
− Min. 650 mm between work surface and top cupboard.
− The strips on the wall edges must be heat-resistant.
− Do not mount the unit above a dishwasher, oven, cooling
units or a washing machine or dryer.
− Make sure there is a distance of 20 mm below the
casing of the unit for proper ventilation.
− Do not store any flammable and not heat-resistant
objects in the drawer below the cooking plate (e.g.
sprays).
− There may be absolutely no mechanical tension on
the connection cable, such as a drawer.
2.2 Install the unit
Follow the steps below for mounting the unit.
1. Unpack the unitl
− Take the unit from the packaging at the place of the
2 cut-aways in the packaging to avoid damaging
the glass.
2. Materials
− Check if all materials have been supplied.
3. Cut-away for surface mounting and flush mounting
− The cooking plate can be mounted both through
surface mounting and flush mounting with respect
to the table top.
Conditions for the cut-away:
• Table tops are to be made from heat-resistant ma-
terials (100°C).
• The materials of the table top can expand when they
come into contact with water. Veneer the cut-away
or coat it with a special type of glue for protection.
• Observe the instructions of the table top manufacturer.
a. Surface mounting
• Make a cut-away in the table top in accordance
with the drawing 3a.
b. Flush mounting
• Make a cut-away and a milling edge in the table
top in accordance with the drawing 3b.
c. Ventilation 1811 One Pro + d. Ventilation 1801
One Power
16