Table of Contents
Advertisement
Quick Links
Wireless Base Stations
▫
and Client Devices
Surveillance Cameras
▫
Remote Sensors
▫
UBNT Equipment
▫
Microtik Equipment
▫
Congratulations! on your purchase of the UPSPro™ outdoor
backup power system. Please take a moment to review this Qwik
Install Guide before assembly or battery installation.
When following the instructions in this guide take extreme care to avoid
contact with overhead power lines, lights and power circuits. Contact
with power lines, lights or power circuits may be fatal. We recommend
to install no closer than 20 feet to any power lines.
Safety:
For your own protection, follow these safety rules.
▫
Perform as many functions as possible on the ground
▫
Do not attempt to install on a rainy, windy or snowy day or if
there is ice or snow accumulation at the install site or if the
site is wet.
▫
Make sure there are no people, pets, etc. below when you are
working on a roof or ladder.
Recommended Tools: Phillips Screwdriver, 13mm and 10mm
Open End Wrench, 8mm nut driver, Flat Blade Screwdriver
Please help preserve the environment and return
used batteries to an authorized depot
UPS-ST2424-UBNT
UPSPro™ Backup
DANGER! Avoid Powerlines!
You Can Be Killed!
Power System
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tycon Power Systems UPSPro
Summary of Contents for Tycon Power Systems UPSPro
- Page 1 ▫ UBNT Equipment ▫ Microtik Equipment ▫ Congratulations! on your purchase of the UPSPro™ outdoor backup power system. Please take a moment to review this Qwik Install Guide before assembly or battery installation. DANGER! Avoid Powerlines! You Can Be Killed! When following the instructions in this guide take extreme care to avoid contact with overhead power lines, lights and power circuits.
- Page 2 Qwik Install STEP 1: Add Grounding Wire Between Door and Enclosure: Remove plastic covers on cop- per studs on inside of door and inside of enclosure. Add jumper wire between 2 copper studs and use copper washers and nuts to secure.
- Page 3 STEP 6: Insert the bat- tery platform in the bot- tom of the enclosure. The battery platform has cutouts so wires can be routed under the battery as needed. STEP 7: Attach the green DIN Rail adapters to the charge controller and 5 port POE switch using the screws provided.
- Page 4 STEP 9: Install the batteries in the en- closure. If using multiple batteries, con- nect in parallel for 12V output or connect in series for 24V output. 24V two batter- ies and 24V four batteries configurations are shown here: STEP 10: If batteries are installed on their side make sure to apply an insulator to the top of the battery termi- nal to prevent the battery terminals from shorting to the metal enclosure in case the battery shifts inside the en-...
- Page 5 24V. This protects battery from overdischarge and increases battery life and performance. 2. CAPACITY: The UPSPro UPS-ST2424-UBNT is rated at up to 30W power output. If you exceed this load the system may not function to expectations.
- Page 6 Wind Turbines are good sources of power, often in times when the sun isn’t shining, like on stormy days. We like to think of a wind tur- bine as uptime insurance. Tycon Power Systems offers small wind tur- bines perfectly suited to augment the UPSPro systems. The TPW-400-...
- Page 7 Just visit tyconpower.com for more info. Compatible Solar Panel Kits Tycon Power Systems Solar Panel kits come with High Performance solar panels, side of pole mounts and out- door rated connection cabling. Solar panels have a 25 year output warranty.
- Page 8 Sealed and maintenance free Limited Warranty The UPSPro™ products are supplied with a limited 24 month warranty which covers material and workmanship defects. This warranty does not cover the following: ▫ Parts requiring replacement due to improper installation, misuse, poor site conditions, faulty power, etc.
Need help?
Do you have a question about the UPSPro and is the answer not in the manual?
Questions and answers