YATO YT-8250 Quick Start Manual

RESISTANCE SOLDERING TOOL
2
5
2
1. casing
2. soldering tip
3. heating element
4. cable and plug
5. soldering tip fi xture
6. protecting sleeve
PROPERTIES OF THE TOOL
The soldering tool has been designed for the purpose of soldering metals with tin and
lead binders for soft soldering. The tool has been designed exclusively for household
applications and must not be used professionally, i.e. in plants and for profi t-making
purposes. A correct, reliable and safe functioning of the tool depends upon appropriate
operation, and therefore: Before work with the tool, read the complete instruction
and keep it. The supplier will not be held responsible for any damage and injuries
which occur as a result of inappropriate applications of the tool, failure to observe safety
regulations and the recommendations specifi ed in these instructions. Improper applica-
tion of the tool will also cause cancellation of any guarantee rights due to incompliance
with the sales contract.
EQUIPMENT
The soldering tool is provided complete and has no additional accessories.
TECHNICAL DATA
Parameter
Catalogue number
Power supply mains
voltage
Power supply mains
frequency
Rated power
Heating time
Working temperature
of the soldering tip
Maximum temperature
of the soldering tip
Dimensions
of the soldering tip
Durability
of the soldering tip
Mass
Electric insulation class
Parameter
Catalogue number
Power supply mains
voltage
Power supply mains
frequency
Rated power
Heating time
Working temperature
of the soldering tip
Maximum temperature
of the soldering tip
Dimensions
of the soldering tip
Durability
of the soldering tip
Mass
Electric insulation class
GENERAL SAFETY CONDITIONS
NOTE! Get acquainted with all the instructions below. Failure to observe them may
lead to an electric shock, fi re or injuries. The notion of electric tool used in the instruc-
tions applies to all the tools which are powered with electric current, both wire tools
and wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean. Disorder and poor il-
lumination may be a cause of accidents. Do not work with electric tools in explosive
environments, or those which contain infl ammable liquids, gases or vapours.
Electric tools generate sparks, which may cause a fi re in case of contact with infl am-
mable gases or vapours. Do not allow children and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must fi t the mains socket. Do not modify
the plug. Do not use any adapters whatsoever in order to adapt the plug to the
socket. Unmodifi ed plug which fi ts the socket reduces the risk of an electric shock.
Avoid contact with grounded surfaces, such as pipes, heaters and refrigerators.
Grounding of the body increases the risk of an electric shock. Do not expose electric
tools to precipitation or humidity. Water and humidity which gets into the electric
tool increases the risk of an electric shock. Do not overload the power supply cable.
Do not use the power supply cable in order to carry the tool or to connect and
disconnect the plug from the mains socket. Avoid contact of the power supply
cable with heat, oils, sharp tools and moving elements. Damage to the power sup-
ply cable increases the risk of an electric shock. In case work is realised outside
closed areas, it is necessary to use extension cords designed for applications
outside closed areas. Using a correct extension cord permits to reduce the risk of
an electric shock.
Personal safety
Commence work in good physical and psychological conditions. Pay attention
3
6
YT-8250
5
6
Unit of
measurement
[V]
[Hz]
[W]
[min]
[ C]
O
[ C]
O
[mm]
[soldering
points]
[kg]
Unit of
measurement
[V]
[Hz]
[W]
[min]
[ C]
O
[ C]
O
[mm]
[soldering
points]
[kg]
1
YT-8251 YT-8252
1
YT-8254 YT-8255
YT-8250 YT-8251 YT-8252 YT-8253
30 40
5 5
300 320
400 420
Ø3,8 x Ø4,9 x
70,8 75,5
0,04 0,06
YT-8254 YT-8255
15
3
300
400
Ø6,4 x 42,7 Ø6,4 x 42,7
0,04
YT-8253
YT-8256
Value
~230
50
50
5
340
440
Ø5,9 x
76,5
60 000
0,07
I
Value
YT-8256
~230
50
25
3
320 350
420 450
Ø8,0 x 57
60 000
0,05 0,07
I
4
4
60
5
350
450
Ø5,9 x
76,5
0,07
35
3