Advertisement
These operating instructions apply to:
Use and storage
Before installing the vibrators read these instructions carefully. It is the basis for any action when dealing
with the vibrators, and may be used for training purposes. The instructions should be subsequently
stored at the operation site.
Copyright
This documentation is protected by copyright.
reprinting and reproduction of the instructions, as well as parts thereof.
Operating instructions for
Netter pneumatic vibrators
Series NCT, NCB and NCR
Pneumatic turbine vibrators
NCT 1
NCT 2
NCT 3
NCT 4 / 4i
NCT 5
NCT 10 / 10i
Pneumatic ball vibrators
NCB 1
NCB 2
NCB 3
NCB 5
Pneumatic roller vibrators
NCR 3
NCR 10
NCR 22
Netter
Vibration reserves all rights such as translations,
February 2021
No. 1882E
Page 1/9
Version 1
NCT 15
NCT 29 / 29i
NCT 55
NCT 108 / 108i
NCT 126
NCT 250 / 250i
NCB 10
NCB 20
NCB 50
NCB 70
NCR 57
NCR 120
Advertisement
Table of Contents
Related Manuals for NetterVibration NCT Series
Summary of Contents for NetterVibration NCT Series
- Page 1 February 2021 Operating instructions for No. 1882E Netter pneumatic vibrators Page 1/9 Series NCT, NCB and NCR Version 1 These operating instructions apply to: Pneumatic turbine vibrators NCT 1 NCT 15 NCT 2 NCT 29 / 29i NCT 3 NCT 55 NCT 4 / 4i NCT 108 / 108i NCT 5...
-
Page 2: General Information
General information The pneumatic vibrators of the series NCT, NCB and NCR are hereafter Designation referred to as "vibrators". Scope of Please refer to the delivery note for the scope of delivery. delivery Check the packaging for possible transport damage. In the event of dam- age to the packaging, check the contents for completeness and possible damage. - Page 3 Safety The vibrators are designed for installation in machines. Intended use General applications are: loosening, conveying, sorting, compacting, sepa- rating bulk materials and reducing friction. The vibrators are used for emp- tying bunkers, as drives for conveyor troughs, as sieves and vibrating ta- bles.
-
Page 4: Technical Data
NOTICE Operation of the vibrators with silencers is mandatory. Silencers reduce the noise level and protect the vibrators from contamination entering. Technical data Permissible operating conditions Drive medium NCT must be operated with clean compressed air or nitrogen according to the following specification, according ISO 8573-1: [ 5 : Filter ≤... -
Page 5: Design And Function
Design and function Housing Hose grommet Turbine with unbalances Air outlet Air inlet Steel ball Silencer Mounting slots Steel roller Function The vibrators generate circular vibrations, i.e. the vibrations act in all directions of a plane. The air inlet (5) and the air outlet (2) are indicated by arrows on the housing (1). The silencer (3) reduces the sound level and protects the interior of the housing from impurity. -
Page 6: Transport And Storage
Transport and storage Special conditions of transport are not required. Transport conditions Storage Storage in a dry and clean environment, protected from UV-exposures, conditions weather and ozone. Storage temperature: -20 °C to 60 °C. Close all openings before storage. Installation Observe the safety instructions in chap. -
Page 7: Start-Up And Operation
Fasten the compressed air supply. The air inlet has a smaller opening than the air outlet. Both are indicated by arrows on the front. Air resistance increases with hose lengh. The nominal widths given above apply to hose lengths up to 3 m. Longer lines require larger cross sections. The escaping air can be discharged via a hose. -
Page 8: Maintenance And Servicing
Maintenance and servicing Observe the safety instructions in chap. Safety, from page 3 on. Clean the surface of the vibrators regularly with a moist cloth to remove Cleaning dust deposits. To clean the vibrators with pressurised water, proceed as follows: Unscrew the silencer and close the exhaust air opening. -
Page 9: Troubleshooting
Troubleshooting Observe the safety instructions in chap. Safety, from page 3 on. Malfunction Possible cause Corrective action Vibrator has too little power Connections switched Place the air inlet on the connection with the smaller bore or does not start (see arrows). Dimensioning Check size of the vibrator.