Gardena MultiControl duo Operator's Manual page 7

Fit anti-theft device (optional) [ Fig. I8 ]:
To secure your Water Control against theft, you
can obtain the GARDENA Anti-theft device
Art. 1815-00.791.00 from GARDENA Service.
1. Screw clamp (22) with screw
of the Water Control.
4. PROGRAMMING
To set the programme, the controller can be
removed and mobile programming can
be carried out (see 3. INITIAL OPERATION
Inserting battery).
Programming can be discontinued at any time by
pressing the Man. button. All programme data
changed up to this time and confirmed with the
OK button is saved.
Set current time and day of week:
1. [ Fig. P1 ]: Press Menu-key [Level 2] (not
necessary if the battery has just been inserted).
The hours display and Time flash.
2. [ Fig. P2 ]: Set the time in hours with the
▼-▲ button (example:
with the OK-key.
Time and the minutes display flash.
3. [ Fig. P3 ]: Set the time in minutes with the
▼-▲ button (example:
with the OK-key.
Time and the day of the week display flash.
4. [ Fig. P4 ]: Set day of week with the ▼-▲ but-
tons (e. g. (Tu) and confirm with the OK button.
The display moves to the message "Entering
watering programme" of the watering mode
"Scheduled watering" [Level 3].
Start Prog and the hours will flash on the
display.
Watering modes:
The Water Control has 3 watering modes:
A) Scheduled watering:
With the "scheduled watering", watering begins
as per the set programme. There is the addi-
tional option to consider soil moisture or rain in
the watering programme. In the case of rain
or sufficiently moist soil, the programme's stop
is activated or activation of the programme is
prevented. Manual watering Man. + OK is still
possible.
B) Direct sensor control :
With "direct sensor control", watering is exclu-
sively controlled in dependency on soil moisture
between 20:00 and 06:00, if the sensor has
(23) firmly to the back
hours) and confirm
9
minutes) and confirm
30
2. Use clamp (22) e. g. for fixing a chain.
It is no longer possible to remove the screw after
it has been screwed in.
indicated dry. 1 or 2 Soil Moisture Sensors can
be connected.
C) Manual watering:
With "Manual watering", watering begins imme-
diately after Man. + OK has been pressed and
can be operated independently of the sensor
status.
Entering watering programme:
A) Scheduled watering:
1. Select programme for Valve 1 ( ï V1) or
Valve 2 (V2 ð ) with the ▼-▲ buttons (V1 / V2),
(not possible if the current time of day and week-
day have been previously entered).
2. [ Fig. P5 ]: Press Menu-key twice [Level 3]
(not necessary if the current time and day of the
week has been entered).
Start Prog and the hours section flash on the
display.
3. [ Fig. P6 ]: Set the watering start time hours with
the ▼-▲ button (e. g.
OK-key.
Start Prog and the minute display flashes on
the screen.
4. [ Fig. P7 ]: Set the minutes for starting the
watering time with the ▼-▲ button
(example: minutes) and confirm with the
20
OK-key.
Run Time and the hours for the watering time
flash on the display.
5. [ Fig. P8 ]: Set the hours for the watering time
with the ▼-▲ button (example:
confirm with the OK-key.
Run Time and minutes for the watering time
flash on the display.
6. [ Fig. P9 ]: Set watering time minutes with the
▼-▲ button (example:
with the OK-key.
Watering cycle flashes on the display.
The watering frequency can be selected by:
• the (7.) watering cycle (right hand column of
the display)
– or –
) and confirm with the
6
hours) and
0
minutes) and confirm
10
17