Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Adaptec AMM-1510M
Summary of Contents for Adaptec AMM-1510M
-
Page 1: Installation Guide
Installation Guide AMM-1525M/1510M/525M SCSI Audio Host Adapters and Sound Cards... -
Page 2: Getting Started
SCSI devices, and up to two IDE devices (standard IDE hard disks and/or ATAPI CD-ROM drives); the AMM-1510M allows you to connect up to seven internal SCSI devices; and the AMM-525M allows you to connect up to two IDE devices. -
Page 3: Default Settings
Host Adapter SCSI ID For AMM-1525M/1510M only. For AMM-1525M/525M only. Host adapter termination is always enabled and cannot be changed. Configured through the aspi2dos.sys command line; see your Adaptec EZ-SCSI User’s Guide. Installing the Host Adapter Changing Jumper Settings In most cases, you will never have to change the default jumper settings;... - Page 4 IRQ Channel and I/O Port Address (AMM-1525M/1510M Only) Jumper block J10 configures the IRQ channel and I/O port address for SCSI. The default configuration is Pin Pair Description I2, I1, I0, I9 Determines the host adapter IRQ channel. IRQ 12 = jumper I2 IRQ 11* = jumper I1 IRQ 10 = jumper I0 IRQ 9 = jumper I9 (not recommended with Windows 3.x)
-
Page 5: Connecting Scsi Devices
IDE Port Enable (AMM-1525M/525M Only) Pins 1 and 2 of jumper block J4 enables or disables the IDE port address. The available settings are Enabled (Default) If you are using the IDE controller on the host adapter, leave this setting enabled. If you are not using the IDE controller on the host adapter, disable this setting. - Page 6 To connect internal SCSI devices, follow these steps: Attach the connector at one end of the 50-pin SCSI ribbon cable to the AMM-1525M/1510M SCSI connector. Make sure to align pin 1 of the cable with pin 1 of the connectors on the host adapter and internal SCSI device.
- Page 7 The aspi2dos ASPI Manager of the Adaptec EZ-SCSI User’s Guide. To change the SCSI ID on your SCSI device, refer to your SCSI device documentation. Connecting IDE Devices (AMM-1525M/525M Only) IDE devices (standard IDE hard disk drives and/or ATAPI CD-ROM drives) are connected to the host adapter by a 40-pin IDE ribbon cable with a 40-pin header connector.
- Page 8 If your computer has an ATAPI CD-ROM drive, be sure the ATAPI CD-ROM driver ( adatapi.sys ) is installed by running the Adaptec Installation Manager. Using Multiple IDE Controllers Up to four IDE devices can be installed in your com- puter by utilizing two IDE controllers.
-
Page 9: Connecting Audio Equipment
For each IDE controller, the first IDE device must be configured as the master device, and the sec- ond (if any) as the slave device. See your IDE device documentation for details. Connecting Audio Equipment You can connect a variety of audio equipment to the AMM-1525M/1510M/525M, such as a microphone, headphone, powered or nonpowered internal/exter- nal speakers, tape deck, CD player, joystick, and... -
Page 10: Installing Software
Installing Software Adaptec Installation Manager Adaptec Installation Manager is a software utility that runs and installs the following Adaptec software needed to operate your host adapter (for more infor- mation, refer to the Adaptec Installation Manager User’s Guide): DeMucker ences to sound boards currently and previously installed in your computer. -
Page 11: Troubleshooting
Adaptec Customer Support For information on software upgrades, new releases, technical advice, and other topics, call Adaptec’s Electronic Bulletin Board Service (BBS) 23 hours a day at 408-945-7727; 1200/ 2400/9600/14400 baud, 8 data bits, 1 stop bit, no parity. The BBS is out of service 1 hour each day. -
Page 12: Fcc Compliance Statement
Adaptec, Inc. 691 South Milpitas Blvd. Milpitas, CA 95035 Copyright © 1994 Adaptec, Inc. All rights reserved. Adaptec, the Adaptec logo, AMM, EZ-Audio, EZ-SCSI, and DeMucker are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. All other trademarks are owned by their respective owners.
Need help?
Do you have a question about the AMM-1510M and is the answer not in the manual?
Questions and answers