Download Print this page

Pivot CYBER GAUGE COW User Manual page 3

Obd or sensor system

Advertisement

Notes about using the OBD2 Connector
M a k e s u r e t o g r i p t h e
distended portions when
pulling it out or inserting it.
If connect the power cable to IGN (Not normally required)
For some models, please connect the power cable to IGN as shown on the right.
Symptom
After stopping the engine, it
Part of SUBARU
takes about a minute until
(Including 86)
the meter turns off.
Sometimes the meter is not
Part of SUZUKI
working.
How to use the Cut Connectors
1
2
10
10
mm
mm
Peel off of the vinyl
Peel off of the vinyl
cover at the end of
cover at connection.
the product' s wire.
Installing The Product
Installing The Meter
A Installation with the Meter Holder
Fa s t e n u s i n g t h e
After deciding the
double-sided tape.
p o s i t i o n a n d
angle of the meter
fac e, fa s te n t h e
Hexagonal bolt on
b o t h s i d e s t o
Double-sided
secure.
tape
Clean
to remove
oil and dust
Note : Please be sure about
where you wish to install the
meter, as it is not advisable to
reuse double-sided tape.
B Installation to panel or something
Cut the Cushion Tape in half, affix to base of the Meter to be
on press fit condition with adjusting number. And connect the
Gauge Cable to the Meter and insert into the panel.
Cushion Tape
Cut the
Cushion Tape
in half
Cushion Tape
Features of the meter
1.0
2.0
BOOST
x100kPa
CYBER GAUGE
-1.0
0
A Must-Have
BOOST
for Turbo Cars
From checking boost to estimating gas
usage (vacuum side) make this a vital
item for your turbo engine car.
CAUTION
D o n o t p u ll o n t h e w i r e s
when trying to remove the
connector; the wires may
become disconnected.
Cause
It's a communication matter with
the car side, but it has no trouble to
the car without changing the wiring.
It's a communication matter with
the car side
3
W r a p a r o u n d
both wire coils.
Affix the Cushion Tape on the base of the meter,
connect the Gauge Cable to the Meter, and install
the Meter into the Meter Holder.
Cushion Tape if the Meter not fixed.
Cushion Tape
Cushion Tape
Hexagonal bolt
Panel
Gauge 
Cable
100
120
80
WATER
TEMP
°C
60
CYBER GAUGE
20
40
For Preventing
WATER
Overheating and
TEMP
Checking Warm-up
This gauge allows you to not only check
warm-up operation but help prevent
overheating due to lack of coolant or
trouble in the coolant line.
If you unable to get a grip
on the distended portions.
W i t h s o m e c ar m o d e l s i t
m ay b e d i f f i c u l t t o g e t a
good grip on the connector.
Yellow
=Cut Connector
Unplug the connector of Yellow and Red cable of OBD Cable
and connect Yellow cable of IGN Cable into the connector on
yellow cable, then connect to IGN cable to IGN of car. (Do not
connect to Acc)
4
5
Insulate with vinyl
Cl ose t i g ht ly wit h
tape.
cut connector.
Please add the
Cushion
Meter Holder
Tape
Back side
of Meter
Gauge Cable
Connector
Installing The Unit
Fastening to
When Fastening
Flat Space
to a Cable or Pipe
Zip tie
(Large)
Unit
Double-sided
tape
Clean to
Thick cable
remove
or pipe
oil and dust.
16
14
17
12
VOLTS
CYBER GAUGE
7
10
8
Battery Checking
VOLTAGE
for New-Era Systems
Use to calculate battery life by checking
voltage drop during idling and minimum
voltage at start up, as well as, check on
your bat ter y rec harging status from
regenerative braking.
In such case, pull
out the connector
by p u l l i n g o n t h e
end of the zip tie.
OBD Cable
Red
Yellow
IGN Cable
(12V with Key ON)
When crimping, please
u s e c r i m p e r s o r u s e
pliers to bend and then
solder together.
● W h e n u s i n g L i n k C a b l e , p u t t h e
connector to the back of Meter Holder
as shown in the below diagram. Push
the remained cable between the meters
to inside of Meter Holder.
Connector
Meter
Meter
Holder
Cable
(Example of Installation)
Through
holes
As shown in the above diagram , fasten
t h e u n i t i n to p o s i t i o n s n o t u s u a l l y
affected by water.
6
5
4
V
3
CYBER GAUGE
2
TACHOMETER
to Eco Driving
A b a s i c t a c h o m e t e r d e s i g n e d f o r
checking shifting performance in both
AT a n d M T c a r s , a s w e l l a s , h e l p
optimize your eco-driving.
Diagnostic
Monitoring
Connector
IGN
Connector
7
8
9
x1000rpm
0
1
From Sports
3

Advertisement

loading

This manual is also suitable for:

Cyber gauge cobCyber gauge covCyber gauge cotCyber gauge cou