Before Connecting; Connecting To The Steering Wheel Remote Controller; Connecting An External Navigation Unit; Connecting The External Components - JVC KW-AVX746 Installation & Connection Manual

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1
Connect the colored leads of the power cord in the order specified in the illustration below.
2
Connect the antenna cord.
3
Finally connect the wiring harness to the unit.
Rear ground
terminal
Antenna
terminal
White with black stripe
A

Connecting to the steering wheel remote controller

If your car is equipped with the steering wheel remote controller, you can operate this unit using the
controller. For connection, an exclusive remote adapter (not supplied) which matches your car is
required. For details, consult the same car audio dealer as where the unit is purchased.
STEERING
WHEEL
REMOTE
B
Connecting the external amplifiers and subwoofer
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it
can be controlled through this unit.
• Disconnect the speakers from this unit, and connect them to the amplifier. Leave the
speaker leads of this unit unused.
• You can switch off the built-in amplifier and send the audio signals only to the external amplifier(s) to
get clear sounds and to prevent internal heat built-up inside the unit.
See page 38 of the INSTRUCTIONS.
To the remote lead of other equipment
* 1 Y-connector
Remote lead
Remote lead (blue
Rear
with white stripe)
speakers
JVC *
5
Amplifier
*
6
E
Connecting the microphone
1
2
Microphone
Adhesive tape
Light green
PARKING BRAKE
(See page 1)
REVERSE
GEAR
SIGNAL
CAMERA IN
SUBWOOFER
OUT
Fan
10 A fuse
8
White Gray with black stripe
Left speaker
(front)
OE remote adapter * 1 * 4
Steering wheel remote controller (equipped in the car)
* 5
* 1
*
5
3
3
Black 1
To metallic body or chassis of the car
(GND)
Yellow * 2
2
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Red 3
Blue
(POWER ANTENNA)
Blue with white stripe
Orange with white stripe
Brown
Gray Green with black stripe
Right speaker
(front)
C

Connecting an external navigation unit

Connect an external navigation unit to the RGB input
terminal. The positional information detected on the
touch panel and picture signals from the navigation
unit are transferred through the terminal.
Refer to the manual of the external navigation unit for
details.
• Please contact your dealer to inquire about compatible navigation units.
• JVC cannot guarantee proper operation of the external devices connected to the RGB input terminal.
D

Connecting the external components

Camcorder
etc.
USB devices
JVC Amplifier
* 6
USB cable (approx. 1 m)
Subwoofer
Front
speakers
JVC
Amplifier
* 6
– To watch the video: USB Audio and Video cable for iPod/iPhone—KS-U30 (not supplied) *
– To listen to the music: USB 2.0 cable (accessory of the iPod/iPhone)
Secure the microphone
cord using cord cramps
(not supplied) if
necessary.
2
Crimp connector
1
* 1
To an accessory terminal in the fuse block
4
To automatic antenna
if any (250 mA max.)
5
To the remote lead of other equipment (200 mA max.)
6
To car light control switch
7
To mobile phone system
3
To the OE remote adapter *
Green Purple with black stripe
Left speaker
(rear)
External
navigation
1
unit *
*
7
*
5
Connecting the iPod or the iPhone
USB 2.0 cable (accessory of the
USB device
* 1 Not supplied for this unit.
* 2 Before checking the operation of this unit prior to installation, this lead must be connected,
otherwise power cannot be turned on. Do not connect the lead directly to the battery.
* 3 Do not connect the lead to any device other than the OE remote adapter. Doing so may cause
malfunction.
* 4 Alter the wire of the OE remote adapter to connect to the steering wheel remote lead.
* 5 Audio cord (not supplied for this unit).
* 6 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated
with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may
cause damage to the unit.
* 7 Video cord (not supplied for this unit).
* 8 When using the cable, you need to change the setting on the unit (see page 28 of the
INSTRUCTIONS).
• iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
• iPhone is a trademark of Apple Inc.
See each diagram below.
To parking brake (see page 1)
Ignition switch
*
1
Fuse block
Purple
Right speaker
(rear)
RGB input terminal
1
KV-CM10 *
Rear view camera
CAMERA IN
*
7
External
monitor
iPod/iPhone)
KS-U30
(not supplied)
8