Acer 1100 User Manual
Acer altos 1100 server: users guide
Hide thumbs
Also See for 1100:
- User manual (30 pages) ,
- User manual (114 pages) ,
- Service manual (180 pages)
Related Manuals for Acer 1100
Summary of Contents for Acer 1100
- Page 1 User’s Guide...
- Page 2 Copyright 1998 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.
- Page 3 All brand and product names mentioned in this manual are trademarks and/or registered trademarks of their respective companies.
- Page 4 1. Read these instructions carefully. future reference. 2. Follow all warnings and instructions marked on the product. 3. Do not use this product near water. 4. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 5.
- Page 5 9. If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed 15 amperes.
- Page 6 13. Replace the battery with the same type as the product's battery we recommend. Use of another battery may present a risk of fire or explosion. Refer battery replacement to a qualified serviceman. 14. Warning! The battery could explode if not handled properly. Do not recharge, disassemble or dispose of it in fire.
- Page 7 DANGER INVISIBLE RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN GEÖFFNET. NICHT IN DEN STRAHL SEHEN. ATTENTION RADIATION DU FAISCEAU LASER INVISIBLE. EN CAS D’OUVERTURE. EVITER TOUTE EXPOSITION AUX RAYONS. VARO AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄ KATSO SÄTEESEEN. VARNING! OSYNLING LASERSTRÄLNING NÄR DENNA DEL ÄR ÖPPNAD.
- Page 8 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Léver det brugte batteri tilbage til leverandøren.
- Page 9 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 10: Manual Structure
Purpose This user’s guide aims to give you the information you need to operate the system properly and tells you how to install internal components. Manual Structure This user’s guide consists of two chapters. Chapter 1 System Board This chapter describes the system board and all its major components. - Page 11 Conventions The following conventions are used in this manual: Text entered by user , etc. Represents text input by the user. Represent the actual keys that you have to press on the keyboard. NOTE Gives bits and pieces of additional information related to the current topic.
- Page 12 Chapter 1 System Board Features... 1-1 Major Components... 1-3 Layout ... 1-4 Jumpers and Connectors... 1-5 1.4.1 Jumper and Connector Locations... 1-5 1.4.2 Jumper Settings... 1-6 1.4.3 Connector Functions... 1-7 ESD Precautions... 1-9 Installing the Pentium II processor... 1-10 1.6.1 Attaching the Processor Heat Sink and Fan...
- Page 13 1.11 Remote Diagnostic Management ...1-25 1.11.1 Installing the RDM Module ...1-25 1.12 Error Messages ...1-26 1.12.1 Software Error Messages ...1-26 1.12.2 System Error Messages ...1-26 1.12.3 Correcting Error Conditions ...1-29 Chapter 2 BIOS Utility Entering Setup ...2 System Information...3 2.2.1 Processor ...4 2.2.2 Processor Speed ...5...
- Page 14 2.2.18 Onboard USB...7 Product Information...8 2.3.1 Product Name...8 2.3.2 System S/N ...8 2.3.3 Main Board ID ...9 2.3.4 Main Board S/N...9 2.3.5 System BIOS Version ...9 2.3.6 System BIOS ID...9 2.3.7 BIOS Release Date...9 Disk Drives...10 2.4.1 Floppy Drives ...12 2.4.2 IDE Drives...12 Power Management...16...
- Page 15 2.7.2 PnP/PCI System Configuration ...30 2.7.3 Memory/Cache Configuration...35 2.7.4 CPU Speed Configuration ...37 2.7.5 System Event Configuration ...38 System Security Setup ...43 2.8.1 Disk Drive Control...43 2.8.2 Setup Password ...44 2.8.3 Power-on Password ...48 Date and Time ...49 2.9.1 Date ...50 2.9.2 Time...50 2.10...
- Page 16 Matching the Fan-Heat Sink Clips with the Holes on the Processor... 1-10 Inserting the Clip Ends into the Processor Holes... 1-11 Locking a Wide Clip End ... 1-12 Locking a Narrow Clip End... 1-12 Installing the processor’s Retention Mechanism... 1-13 Installing a Pentium II Processor...
- Page 17 List of Tables System Board Jumper Settings ...1-6 Connector Functions...1-7 Memory Configurations...1-17 System Error Messages...1-27 Parallel Port Operation Mode Settings...2-28 Drive Control Settings ...2-46 SCSI/VGA Combo Card Jumper Settings ...3-3 SCSI/VGA Combo Card Connector Functions ...3-3 Supported Video Resolutions ...3-6 xvii...