Sony STR-DA2800ES Service Manual page 156

STR-DA2800ES
Pin No. Pin Name
F16 AVSS12_HDMI_TX
F17 AVSS33_HDMI_TX
F18 AVDD33_VDAC_R
F19 AVSS33_VDAC_X
F21 VDIN34
F22 VDIN23
F24 ETTXER/DDC_SCL
F25 ETRXD0
F26 ETCRS/HPG_RX
F27 VDINVSYNC
F28 VDINCLK
G1 INB
G2 INA
G3 TRINA
G4 AUX1
G5 VWDC3O
G6 AGND12_1A
G7 AVSS12_REC
G9 GPIO2
G11 BCK
G14 AVSS12_APLL
G15 AVDD12_APLL
G16 AVSS12_HDMI_TX
G17 AVSS33_VDAC_R
G20 VDIN35/LIN
G23 ETTXD0
G24 ETTXCLK
G25 ETRXD3
G26 ETRXCLK
G27,
ETRXD1, ETRXD2
G28
H1 IND
H2 INC
H3 TRINC
H4 TRINB
H5 TRIND
H6 FVREF
H21 DVCC33_IO_STB
H22 AVSS33_LDO
H23 ETTXD1
H24 GPIO8/5V_RX
H25 ETTXEN
H26 ETTXD3
J3 INH
J4 ING
J5 AVDD33_1A
J6 AGND33_1A
J13, J14 DVCC33_IO_5
J18, J19 DVCC33_IO_3
J21 DVCC33_IO_STB
J23 ETTXD2
J24 AVDD33_LDO
J25 UARXD
J26 ETMDIO
J27 ETCOL
J28 ETMDC
K1 RFIP
K2 RFIN
156
I/O
- Ground terminal
- Ground terminal
- Power supply terminal (+3.3V)
- Ground terminal
Update signal output to the sub system controller, main system controller, video system con-
O
troller and video controller
O VBUS power supply on/off control signal output terminal
O I2C serial data transfer clock signal output terminal
I Digital audio/video signal input from the ethernet interface
O Hot plug detection signal output terminal
O Vertical sync signal output terminal
O Video clock signal output terminal
I Main beam (B) input terminal
I Main beam (A) input terminal
I Tracking signal (A) input terminal
I Monitoring signal input terminal
O Laser diode control voltage output terminal
- Ground terminal
- Ground terminal
O Relay drive signal (for main power) output terminal
O Bit clock signal output to the A/D converter (for network audio section)
- Ground terminal
- Power supply terminal (+1.2V)
- Ground terminal
- Ground terminal
Update signal input from the sub system controller, main system controller, video system
I
controller and video controller
O Digital data output to the ethernet interface
O Serial data transfer clock signal output to the ethernet interface
I Digital audio/video signal input from the ethernet interface
I Serial data transfer clock signal input from the ethernet interface
I Digital audio/video signal input from the ethernet interface
I Main beam (D) input terminal
I Main beam (C) input terminal
I Tracking signal (C) input terminal
I Tracking signal (B) input terminal
I Tracking signal (D) input terminal
O Reference voltage output terminal
- Power supply terminal (+3.3V)
- Ground terminal
O Digital data output to the ethernet interface
I Power supply voltage (+5V) input terminal
O Enable signal output to the ethernet interface
O Digital data output to the ethernet interface
O Sub beam (H) input terminal
O Sub beam (G) input terminal
- Power supply terminal (+3.3V)
- Ground terminal
- Power supply terminal (+3.3V)
- Power supply terminal (+3.3V)
- Power supply terminal (+3.3V)
O Digital data output to the ethernet interface
- Power supply terminal (+3.3V)
I Receive data input terminal
I/O Two-way management data bus with the ethernet interface
I Collision detection signal input from the ethernet interface
O Management data clock signal output to the ethernet interface
I BD RF signal (positive) input terminal
I BD RF signal (negative) input terminal
Description
"H": power on
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
"H": relay on
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used
Not used