Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for IBA ibaDeskline SAS
Summary of Contents for IBA ibaDeskline SAS
- Page 1 SAS iba Industrial Computer Manual Issue 1.4...
- Page 2 Required corrections are contained in the following regulations or can be down- loaded on the Internet. The current version is available for download on our web site http://www.iba-ag.com. Windows® is a label and registered trademark of the Microsoft Corporation. Other prod- uct and company names mentioned in this manual can be labels or registered trade- marks of the corresponding owners.
-
Page 3: Table Of Contents
Maintenance work ..................26 Basic procedure ..................26 Power supply slide-in module for replacement of redundant power supply unit ................ 26 Restoring of a RAID system during operation ..........27 Installing operating system and iba software ..........32 Installation ....................32 Issue 1.4... - Page 4 Enter the product key .................. 33 9.2.4 Partitioning ....................34 9.2.5 Completing installation ................36 Windows Updates ..................36 Antivirus Software ..................36 Installing iba software .................. 36 Technical data ....................37 10.1 Main data ....................37 10.2 Electronic components and interfaces ............38 10.3 Products ......................
-
Page 5: About This Manual
SAS Manual About this manual This manual describes the construction, the use and the operation of the industrial PC ibaDeskline SAS. Target group This manual addresses in particular the qualified professionals who are familiar with han- dling electrical and electronic modules as well as communication and measurement tech- nology. -
Page 6: Used Symbols
Manual ibaDeskline SAS Used symbols If safety instructions or other notes are used in this manual, they mean: The non-observance of this safety information may result in an imminent risk of death or severe injury: By an electric shock! ... -
Page 7: Scope Of Delivery
Recovery DVD (for the respective Windows version with all associated operating system settings) iba software, optional order Hardware driver (motherboard, graphics card) 1 iba software license key (dongle), optional with iba software product Serial number (iba-S/N) Issue 1.4... -
Page 8: Versions
Manual ibaDeskline SAS Versions ibaDeskline SAS (Xeon E3, Windows 10 IoT Enterprise Long-Term-Servicing ver- sion, PCIe) with one hard disk, can be upgraded with up to 7 further hard disks Upgrade options: RAID 1 system with 2 hard disks, 1 redundant power supply unit Data are mirrored. -
Page 9: Safety Instructions
SAS Manual Safety instructions Designated use The device may be used only for the following applications: Machine test and commissioning of industrial systems Measurement data logging and analysis Applications of ibaSoftware products (ibaPDA, ibaLogic etc.) Proper installation site According to manufacturer's specifications the device can only be installed on an even non-slip installation surface, for example table or rack. -
Page 10: Description
Manual ibaDeskline SAS Description Front view ibaDeskline Optical drive with integrated writing function Plug-in slots for hard disks Issue 1.4... -
Page 11: Top View
SAS Manual Top view ibaDeskline USB 2.0 interfaces USB 3.0 interfaces Headset interface Microphone interface Power button Reset button Issue 1.4... -
Page 12: Rear View
5.3.1 Standard system version Connections for external devices (keyboard, mouse, network etc.) Slots X20 to X26 (for low-profile iba cards) Slot X2 for hard disk controller Slots X3 to X7 (PCIe, in the example with 2 ibaFOB-D cards Slot X8 DVI connection... -
Page 13: Version With Redundant Power Supply
RAID systems are equipped with a redundant power supply unit. Connections for external devices (keyboard, mouse, network etc.) Slots X20 to X26 (for low-profile iba cards, e. g. output connections of FOB-4i cards) Slot X2 for hard disk controller Slots X3 to X7 (PCIe, in the example with 2 ibaFOB-D cards... -
Page 14: Internal View
Manual ibaDeskline SAS Internal view Power supply unit (redundant for RAID systems) PCIe slots Hard disk controller Slots for low-profile iba cards Drive bracket Fan ( Ø 12 cm) Internal USB port (dongle) Issue 1.4... -
Page 15: Error Monitoring
SAS Manual Error monitoring Example: Built-in ibaOut-Temp card The temperature and the status of the power supply unit can be monitored with the slot cards ibaOut-Temp and ibaOut-State. The cards can be ordered separately as acces- sory. If the card is ordered with ibaDeskline, it is installed by default in slot X20. If the plug-in card is installed at a later time, please refer to chapter 7.4. -
Page 16: Ibaout-Temp
Manual ibaDeskline SAS 5.5.1 ibaOut-Temp ibaOut-Temp provides two relay outputs for temperature and power supply (2-pin con- nector), which can be used to indicate errors. Both error types are indicated separately. The switch position of the outputs is as follows:... -
Page 17: Ibaout-State
The behavior of ibaOut-State is identical with the previous models with a relay output, if pin 5 and 6 are used. The relay contact of the previous iba-PC models is closed when an error occurs, without differentiating between overtemperature or a power supply error. -
Page 18: Installation, Connection And First Switching On
Manual ibaDeskline SAS Installation, connection and first switching on Safety instructions Electric Shock! Never use the device with a damaged mains cable! Connect the device to one supply voltage only according to specifications on the built- in power supply unit! -
Page 19: Connection And First Switching On
1. Connect the device to a mains socket using the mains cable. 2. Connect all cables. 3. Switch on the device using the mains switch. 4. Boot the device. Press the Power button. The computer is booted automatically with Windows. 5. Finally, start all iba-software applications. Issue 1.4... -
Page 20: Installation Of Measuring Or Additional Boards
Manual ibaDeskline SAS Installation of measuring or additional boards Safety instructions and notes Electric Shock! Before opening shut down the device! After that disconnect it from the mains and pull out the mains plug from the socket equipped with earthing contact! -
Page 21: Opening The Device
SAS Manual Opening the device 1. At the rear side, loosen the two screws fixing the side panel. 2. Push the side panel slightly backwards. 3. Tilt the side panel and pull it upwards. Issue 1.4... -
Page 22: Installing Ibaout-Temp/Ibaout-State
Manual ibaDeskline SAS Installing ibaOut-Temp/ibaOut-State The temperature and the status of the power supply unit can be monitored with the slot cards ibaOut-Temp and ibaOut-State, see also chapter 5.5. The installation procedure is identical for both cards. The installation is described below using the example of ibaOut-Temp in an ibaRackline system. - Page 23 SAS Manual Electrostatic discharge! Touch the components only in electrostatically discharged state! Hold the card cautiously at the edges and at the slot bracket. 7. Insert the card in the respective slot. The bar at the bottom is used to fix the card.
- Page 24 Manual ibaDeskline SAS (1): Connection of redundant power supply unit: If a redundant power supply unit is to be monitored, connect the twisted cable (black/red) of the power supply unit (1 – picture above) to the 2-pin connector (1 – picture below) of the card. This connec- tion is not necessary, when a standard power supply unit is used.
- Page 25 SAS Manual 10. Properly installed card: 11. Fix the cable with a cable tie and close the housing cover. Issue 1.4...
-
Page 26: Maintenance Work
Manual ibaDeskline SAS Maintenance work Basic procedure If you carry out any maintenance work at the device, always proceed in the following way: 1. Remove all mobile data carriers (DVD, memory cards and so on). 2. Shut down the device. -
Page 27: Restoring Of A Raid System During Operation
SAS Manual 1. Loosen the fastening screw which is used to secure the power supply slide-in module at the rack. 2. Pull out the power supply slide-in module. 3. Replace the power supply slide-in module with the module of the same type (availa- ble at iba). - Page 28 Manual ibaDeskline SAS 3. A click on <Login> opens the program window of the manager. The defective hard disk is not indicated. 4. Mark the hard disk, which is available (“Device 1” in the example above) and click on the „Locate“ icon in the “Physical device”...
- Page 29 SAS Manual 6. The new hard disk is indicated in the „maxView Storage Manager“. But the hard disk has not been registered in the system. 7. Mark the new hard disk („Device 2“ in the example above) and click on the „Initialize“...
- Page 30 Manual ibaDeskline SAS 10. Confirm the following overview with <Finish>. 11. The following message appears when the operation was successful. Otherwise an error message appears. Issue 1.4...
- Page 31 SAS Manual 12. The progress of the rebuild process is displayed under “Tasks”. 13. As soon as the hard disk has been successfully registered in the system, the pro- gram can be closed. Issue 1.4...
-
Page 32: Installing Operating System And Iba Software
If you modify the device components, it may not be possible to install it with the Recov- ery DVD. Installing Windows from the recovery medium Important note The Windows license is bound to the computer where iba software is installed. The li- cense must not be used on another computer. 9.2.1 General ... -
Page 33: Select The Language
SAS Manual Note No liability is assumed for the loss of data due to incorrect handling. Always make sure, that you select the correct drives and partitions. Note The recovery process takes approx. 50 minutes. It is possible that only a black or green screen is visible during the process. -
Page 34: Partitioning
Manual ibaDeskline SAS 9.2.4 Partitioning There are several possibilities to set up partitions: Set up a new drive completey as system drive Set up partitions on a new drive Install an operating system on a drive already used (Windows 10 Enterprise or Win- dows Server) ... - Page 35 SAS Manual 2. Click <New> 3. Enter the partition size 4. Confirm with <Apply> 5. Mark the partition, where the operating system should be installed 6. Click <Next> and continue with chapter 9.2.5 „Completing installation“. Possibility 3: Restoring or replacing the operating system The drive is already in use and you want to install the operating system.
-
Page 36: Completing Installation
The procedure takes 30-40 min. depending on the hardware. Windows Updates The automatic search for updates is deactivated by default on iba systems, as iba does not know which Windows update policies apply in your company. Please adjust the settings according to the update policies in your company. Consult your IT department if necessary. -
Page 37: Technical Data
90 V to 264 V AC 110 V to 374 V DC 8 A/4 A 47 Hz to 63 Hz Power output ibaDeskline SAS standard Max. 400 W ibaDeskline SAS RAID 100 V to 240 V AC; 8 A/4 A... -
Page 38: Electronic Components And Interfaces
7.1 channel HD Working memory 16 GB DDR3-RAM Slots PCI Express x16 for SAS-RAID controller 5x PCI Express for iba measuring cards USB 2.0 2 x backside, 2 x topside, 1 x inside (dongle) USB 3.0 4 x backside, 2 x topside... -
Page 39: Products
Manual 10.3 Products PC systems Order number ibaDeskline SAS, XEON E3, Windows 10 IoT Enterprise 2016 LTSB , PCIe 40.002005 (1 hard disk, can be upgraded with up to 7 hard disks) ibaDeskline SAS, XEON E3, Win10, PCIe, SSD 40.002015... -
Page 40: Device Dimensions
Manual ibaDeskline SAS 10.4 Device dimensions (dimensions in mm) Issue 1.4... -
Page 41: Support And Contact
Mailing address iba AG Postbox 1828 D-90708 Fuerth Germany Delivery address iba AG Gebhardtstrasse 10 DE-90762 Fuerth Germany Regional and Worldwide For contact data of your regional iba office or representative please refer to our web site www.iba-ag.com. Issue 1.4...