Interface for Arm Applications ... 5 Connecting the Display ... 5 Connecting the AC Power... 5 Connecting the Audio Cable (For AL1515 m and AL1515 bm) ... 6 Power Management System ... 6 Chapter 2 Display Controls ... 7 General Instructions ... 7 Front Panel Control...
Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. This document contains proprietary information protected by copyright.
Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean LCD Monitor screen; -- Power off LCD Monitor and unplug the AC Cord. -- Spray a non-solvent cleaning solution onto a rag. -- Gently clean the screen with dampened rag.
* User's Manual * Quick Guide * 1.8M Monitor-to-PC VGA Cable * 1.8M Stereo Jack Audio Cable (for AL1515 m and AL1515 bm) * 1.8M Power Cord * Base If you find that any of these items is missing or appears damaged, contact your dealer immediately.
Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the hinge to release. Interface for Arm Applications Before installing to mounting device, please refer to Fig.1-3. The rear of this LCD display has four integrated 4 mm, 0.7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4.
Connecting the Audio Cable (For AL1515 m and AL1515 bm) 1. Connect the audio cable to the " LINE OUT " jack on your PC's audio card or to the front panel's “AUDIO OUT” jack of your CD ROM drive. (See Fig. 1-7) 2.
Chapter 2 Display Controls General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 2-1). By changing these settings, the picture can be adjusted to your personal preferences.
Front Panel Control /Power Button: Press this button to turn the monitor ON or OFF, And display the monitor’s state. Power Indicator: Green — Power On mode. Orange — off mode MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Volume Adjust OSD status.
How To Adjust A Setting 1. Press the MENU-button to activate the OSD window. 2. Press < or > to select the desired function. 3. Press the MENU-button to select the function that you want to adjust. 4. Press < or > to change the settings of the current function. 5.
English 繁體中文 Deutsch Français Multi-language selection. Español Italiano 简体中文 日本語 Adjust the horizontal position of the OSD. H. Position V. Position Adjust the vertical position of the OSD. OSD Timeout Adjust the OSD timeout. Auto Adjust the H/V Position, Focus and Auto Config Clock of picture.
Lamp Current Viewing Angle Display Colors Video Input Signal Input Impedance Polarity Amplitude Multi-mode Supported Control Power switch Audio (AL1515 m/AL1515 bm) Input Output Brightness Contrast Horizontal Position Vertical Position Phase Clock Display Mode Setup 15" (43 cm) Active matrix color TFT LCD...
Power Management Mode Power Consumption* 35W maximum 3W maximum Soft switch off 3W maximum Disconnected 3W maximum * Meeting VESA DPMS requirements measured from AC Input end of AC power cord. Sync Input Signal Polarity Plug & Play External Connection Power Input (AC input) Video Cable Audio Cable...
Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. TIMING FH(KHZ) SYNC FV(HZ) POLARITY 640x350 31.469 VGA-350 70.087 – 640x400 24.83 – NEC PC9801 56.42 – 640x400 31.469 –...
TIMING FH(KHZ) SYNC FV(HZ) POLARITY 800x600 46.875 VESA-600-75Hz 1024x768 48.363 – 60.004 – 1024x768 53.964 COMPAQ-XGA 66.132 1024x768 56.476 – VESA-768-70Hz 70.069 – 1024x768 60.023 VESA-768-75Hz 75.029 1024x768 60.24 – APPLE MAC-768 75.02 – Note: Mode 640x350, 640x400 and 720x400 will locate on middle position but not sure be expanded to full screen on vertical direction.
Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This LCD Monitor Supports Multiple VGA Modes.