Advertisement
E
m
e
r
g
e
n
c
y
P
E
m
e
r
g
e
n
c
y
P
E
E
a
a
s
s
y
y
&
&
E
E
x
x
c
c
h
h
a
a
n
n
g
g
e
e
L
o
n
g
b
a
t
t
e
r
y
l
i
f
e
L
o
n
g
b
a
t
t
e
r
y
l
i
f
e
W
W
a
a
t
t
e
e
r
r
p
p
r
r
o
o
o
o
f
f
Halo-VRI is designed to be worn by seniors as they move on the premises. In an emergency, help is merely a
button press away.
A
c
t
i
v
e
B
u
t
A
c
t
i
v
e
B
u
t
Pressing the Active Button for more than 1 second will activate the Control Panel, causing it to
dial emergency call or alarm.
Press and hold the Active Button for 8 seconds to send a Cancel Code to the Control Panel.
(This function is not compatible with every control panel).
Press and hold the button for 15 sec (until the LED flashes 3 times) to activate the Auto Low
Battery Detection. Halo-VRI will automatically check battery voltage every 20-24 hours.
L
E
D
i
n
d
i
c
a
t
L
E
D
i
n
d
i
c
a
t
The LED will flash 6 times when the button is pressed.
Flashes 3 times: When Auto Low Battery detection function is enabled.
e
n
d
a
n
t
/
W
r
i
s
e
n
d
a
n
t
/
W
r
i
s
a
a
b
b
l
l
e
e
B
B
e
e
l
l
t
t
/
/
N
N
e
e
c
c
k
k
C
C
t
o
n
t
o
n
o
r
o
r
t
T
r
a
n
s
m
i
t
t
e
r
t
T
r
a
n
s
m
i
t
t
e
r
o
o
r
r
d
d
s
s
t
t
y
y
l
l
e
e
s
s
1
(
H
a
l
o
-
V
R
I
)
(
H
a
l
o
-
V
R
I
)
Advertisement
Table of Contents
Related Manuals for Climax Technology Halo-VRI
Summary of Contents for Climax Technology Halo-VRI
- Page 1 & & Halo-VRI is designed to be worn by seniors as they move on the premises. In an emergency, help is merely a button press away. Pressing the Active Button for more than 1 second will activate the Control Panel, causing it to dial emergency call or alarm.
- Page 2 Step 1. Put the Control Panel into the learning mode. Step 2. Press the Button on the Transmitter, a radio signal will be transmitted to the Control Panel. Step 3. Please refer to the operation manual of your Control Panel to complete the learning process.
- Page 3 Picture A. The Back of the transmitter Picture B. The front view of the transmitter and the wrist band with the wrist band The Transmitter features Auto Low Battery detection function. Press and hold the Active Button for 15 seconds to activate this function (ignoring the and 2 set of LED flashes at the first and 8th seconds).
- Page 4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the Halo-VRI and is the answer not in the manual?
Questions and answers