Advertisement
JA-160PC Wireless PIR motion detector combined with a camera
Side view
PIR
Camera
Saving and browsing the pictures
Every picture is taken as a double exposure: the first with low
resolution (LQ = 320 x 240 pixels), second with high resolution (HQ =
640 x 480 pixels).
All of the exposures are saved in the internal memory (micro SD on
the detector PCB) into the independent folders Foto_LQ and Foto_HQ.
When the card is fully loaded, the oldest pictures are replaced by new
ones. Pictures saved on the micro SD card can be browsed by a usual
PC browser. Note: Some antivirus software writes checking data on the
micro SD card. After reinserting the SD card into the detectors, due to
the unknown file (the checking data) card formatting will be performed.
The SD card formatting erases all data which has been saved. For
more information about formatting see
Photos are sent to the control panel in LQ. You can browse through
the images by F-Link and J-Link software (In the event memory, click
on the event New image). Pictures are displayed in LQ, if you click on
Detail you can get second-exposure pictures (HQ). Images can be
searched and browsed by a file manager or picture browser. For
another option to show the pictures it is necessary to start F-Link (J-link)
software and be logged into the control panel as a service technician or
Administrator and then under Disc: Flexi_log /Foto photos which have
been sent to the control panel (LQ) and photos which have been
requested in Detail (HQ) are available.
Picture transmission from the control
panel
Choose one of these options to send pictures to the user:
Transfer photos to the Jablotron Web Self Service
When the customer uses WSS services, then access to the
photos is automatically allowed. Settings of the control panel for the
transfer of pictures are done when the panel is registered. All the
photos are saved and visible in the WSS. Every single photo can
be requested in HQ resolution. The WSS has an option to fill in
telephone numbers for sending the links of the pictures via SMS or
e-mails to get the photos when they are taken. Using the WSS it is
possible to request a new picture without PG output activation (see
Installation recommendations, cautions).
Transferring pictures to external mass storage
If the WSS is not available, photos can be transferred to external
mass storage for example: http://img.jablotron.com. Communication
parameters are preset on the factory and they are activated when the
first PIR detector with a camera is enrolled to the system. First create
an account at http//:img.jablotron.com. Enter your login and password,
then fill in the registration code of the control panel and the photos will
be immediately accessible for browsing. The registration code is on the
control panel PCB or you can read it via F-Link software,
Communication tab, Registration code field. From this mass storage
area a report of new pictures can be sent as an e-mail.
When the picture is saved on the WSS or http://img.jablotron.com,
the control panel sends an SMS report to all selected users according
to the F-link software, User reports tab, Alarm photo settings. Sent
SMSes include an http link for displaying the photo, which on cell
phones with an internet connection, can be displayed directly.
CAUTION: Because this detector allows you to take photos when the
system is unset by a PG state or from the WSS, the producer strictly
warns the user that the detector has to be used within the limits given
by particular laws or norms, especially norms about the protection of
personal privacy.
JA-160PC Wireless PIR motion detector combined with a camera
Top view
Formatting the micro SDcard
(WSS)
The use of the detector is also subject to regulations on the protection
of personal data and the manufacturer recommends that users should
be aware of the obligations applicable to the operation of CCTV.
According to these regulations users have an obligation to ensure the
approval of persons in range of the detector during the acquisition of
photos or the obligation to indicate the image capture area by the
information tables.
Formatting the micro SDcard
The detector is supplied with a formatted Micro SD card (12). The
indication LED (11) is turned off in normal detector mode. Slow LED
flashing indicates that some recording has been done on the SD card,
or the SD card has been changed. The detector works normally with a
new SD card only if the detector performs a card format. Formating the
SD card is done after pressing the tamper contact (14). The formatting
procedure is indicated by quick flashing of the LED (11). During this
process all photos on the SD card are erased.
Installation recommendations, cautions
Several JA-160PCs can be installed in the system. When several
−
detectors are triggered at the same time, the transmission time to
the control panel and outward is extended. A whole transmission
can take a few minutes.
For taking photos by PG status set PG outputs / Function Impulse to a
−
time of 1 min. minimum via F-Link software. The PIR has an internal
algorithm which limits taking a photo by PG status to 1 photo per
minute.
The number of pre-alarm photos taken by a PG output is limited to 40
−
photos per day. The photo counter is reset at 00:00 hrs. Alarm photos
and photos via the WSS have no limitation.
In the WSS Photo gallery / Sending notifications and
−
in
http://img.jablotron.com
maintenance mode by J-Link software all users have access to the
.
photos from all the system sections.
Before you start using the WSS or external mass storage area
−
check the cost for GPRS transfers with your GSM provider.
1.
Remove the batteries from the detector
2. Connect the mini USB cable to the connector (13) and then put
back the batteries.
3. Bootloader mode is indicated by the red LED lighting and by short
flashing of the yellow LED.
4. Then continue the same way as if you want to upgrade the control
panel: Control panel → upgrade Firmware → choose the FW pack
file → in the window where you are offered a device for upgrading
select the USB option and type of device.
Technical specifications
Power
Typical lifetime
about 2 years (1 activation takes 1 series of photos a day)
Recommended installation height
Detection angle / detection coverage:
Horizontal camera capture angle
Range of the flash
Resolution of the camera
Photo size LQ/HQ (typically)
Typical (LQ) photo transmission time to the control panel (ideally)
Typical (HQ) photo transmission time from the control panel (ideally)
Typical photo transfer time from the system to the server
Operational environment according to EN 50131-1
Operational temperature range
Dimensions, weight
Classification
According to
Also complies with
Can be operated according to ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the
in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. The original of the conformity
assessment can be found at
Support section
Note: Although this product does not contain any harmful materials
we suggest you return the product to the dealer or directly to the
producer
www.jablotron.com
2 / 2
Premises / Share and during
FW upgrade
.
2 AA (LR6) 1.5V 2400 mAh alkaline batteries
2.5 m above the floor
55° / 12 m (basic lens)
LQ 320 x 240; HQ 640 x 480 pixels
2-10 kB / 2-64 kB (6 kB / 35 kB)
up to 20 sec. (10 sec.)
up to 130 sec. (60 sec.)
15 s/GPRS; 2 s /LAN
110 x 60 x 55 mm, 102 g
EN 50131-1, EN 50131-2-2
ETSI EN 300 220, EN 50130-4,
EN 55022, EN 60950-1
www.jablotron.com
after
use.
For
more
detailed
43°
max. 3 meters
II. Indoor general
-10 to +40 ° C
Grade 2
JA-160PC
is
- Technical
information
visit
MMQ51100
Advertisement
