Technische Daten
Maximale Belastbarkeit
des gesamten Decoders
Motorausgang
Funktionsausgang A und B
Funktionsausgang C
Funktionsausgang D
Lokadressen
Fahrstufen
Abmessungen
Eigenschaften:
•
Regelung der Motordrehzahl (Lastausgleich)
•
getrennt einstellbare Anfahr- und Bremsverzögerung
•
einstellbare Maximalgeschwindigkeit
•
Programmieren während des Betriebes
•
Mehrfachtraktion
•
4 Funktionsausgänge, vielseitig einsetzbar:
Funktionsausgänge A und B:
richtungsabhängige Funktion (F0), Ausgang A
vorwärts aktiv, Ausgang B rückwärts aktiv
einzeln schaltbar: Ausgang A reagiert auf F0,
Ausgang B reagiert auf F1
einzeln dimmbar
Marslight
Gyrolight
Strobe
Double Strobe
Funktionsausgänge C und D:
Reaktion auf F1 bis F8 frei einstellbar (Mapping)
Blinkbetrieb
Ditchlight (abwechselndes Blinken)
•
Betrieb auf Gleichstromanlage (Analogbetrieb) möglich.
Diese Eigenschaft ist abschaltbar.
LE130XF mit Kabelanschluß zum Anlöten
LE131XF mit Schnittstelle nach NEM652 / NMRA
Wichtige Sicherheitshinweise
Digital plus Lokdecoder dürfen ausschließlich verwendet
werden mit Lenz DIGITAL plus oder einer anderen
handelsüblichen Digitalsteuerungen mit NMRA-Konformitäts-
Siegel. Fragen Sie im Zweifelsfall beim Lieferanten des
Systems nach.
Beachten Sie die maximale Belastbarkeit des Motorausgangs
und der Lichtausgänge. Sie müssen sicherstellen, daß diese
maximale Belastbarkeit nicht überschritten wird. Bei einer
Überlastung wird der Empfänger zerstört! Die Bauteile des
Lokempfängers dürfen auf keinen Fall Metallteile des Chassis
oder des Lokgehäuses berühren. Es entsteht ein Kurzschluß
innerhalb des Lokempfängers, und er wird zerstört.
Wickeln Sie aber den Lokempfänger nie in Isolierband ein,
Seite 1 von 6 / Page 1 of 6
Technical data
current carrying capacity
of the decoder in sum
motor output
function output A and B
function output C
function output C
Addresses
speed steps
Dimensions
1 A
1 A
150 mA
500 mA
150 mA
1 - 9999
14, 27, 28, 128
22,5x16,2x5,3 mm
Features:
•
back emf-feature (constant speed)
•
acceleration and deceleration seperately adjustable
•
adjustable maximum speed
•
Programming on Main
•
multi unit capability (advanced consisting)
•
4 function outputs may be configured in many ways:
Function outputs A and B:
depending on direction (F0), output A forward active,
output B reverse active or
individually, output A reacts on F0, output B reacts on
F1
outputs can be dimmed
Marslight
Gyrolight
Strobe
Double Strobe
Function outputs D and C:
mapping to F1 through F8
blinking
Ditchlight
•
Operation on standard DC systems (analogue operation)
possible. This feature can be disabled.
LE130XF with cable connection
LE131XF with NEM652 plug
Important safety instructions:
The Digital plus locomotive decoders are to be used only with
Lenz Digital plus or other standard digital control with an
NMRA-conformance seal. If in doubt, ask the system suppliers.
Note the maximum current-carrying capacity of the motor
output and the light outputs. Make sure that the maximum
current-load is not exceeded. Exceeding this will destroy the
decoder! The parts of the locomotive decoder must not on any
account touch the metal components of the chassis or the
body of the locomotive. This could cause a short-circuit within
the locomotive decoder which might destroy it.
Never wrap the locomotive decoder in insulating tape, as this
prevents the necessary air circulation around the decoder.
Instead, put insulating tape or something similar around the
Information
LE130XF
Art. Nr. 10132
LE131XF
Art. Nr. 10133
st
1. Auflage / 1
Edition 0701