Advertisement

OUTDOOR FIREPLACE MANUAL
MODELS: OFP42N, OFP42NE, OFP42NE2, OFP42LP, OFP42LPE, OFP42LPE2,
OFP42NS, OFP42NSE, OFP42NSE2, OFP42LPS, OFP42LPSE, OFP42LPSE2
CERTIFIED FOR USA & CANADA- ANSI Z21.97-2017 • CSA 2.41-2017 -
OUTDOOR DECORATIVE GAS APPLIANCES
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
DANGER
This appliance is designed as an "attended appliance". Adults
must be present when the unit is operating. DO NOT leave this
unit burning when unattended. If this product is left burning
unattended it may cause damage or serious injury.
Kingsman Fireplaces 2340 Logan Ave., Winnipeg, Mb Canada Ph: 204-632-1962
CARBON MONOXIDE HAZARD
This appliance can produce carbon
monoxide which has no odor.
Using it in an enclosed space can
kill you.
Never use this appliance in an
enclosed space such as a camper,
tent, car or home.
FIRE OR EXPLOSION HAZARD
If you smell gas:
 Shut off gas to the appliance.
 Extinguish any open flame.
 If odor continues, leave the
area immediately.
 After leaving the area, call your
gas supplier or fire
department.
Failure to follow these
instructions could result in fire
or explosion, which could
cause property damage,
personal injury, or death.
Do not store or use gasoline or
other flammable vapors and
OFP42
OUTDOOR FIREPLACE
liquids in the vicinity of this or
any other appliance.
An LP-cylinder not connected
for use shall not be stored in
the vicinity of this or any other
appliance.
installer, service agency, or the
Printed in Canada P/N 42OFP-MAN17 May 13, 2020
DANGER
WARNING
WARNING
For Outdoor Use Only.
Installation and service must
be performed by a qualified
gas supplier.
WARNING
If the information in this
manual is not followed exactly,
a fire or explosion may result
causing property damage,
personal injury, or loss of life.

Advertisement

Table of Contents
loading

Summary of Contents for Kingsman OFP42N

  • Page 1: Cover

    Kingsman Fireplaces 2340 Logan Ave., Winnipeg, Mb Canada Ph: 204-632-1962 Printed in Canada P/N 42OFP-MAN17 May 13, 2020...
  • Page 2: Warnings, Installations And Operations

    Warnings, Installations and Operations WARNING FOR SAFE INSTALLATION AND OPERATION OF YOUR GAS FIREPLACE PLEASE NOTE THE FOLLOWING: when an appliance is for connection to a fixed piping system, the installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 • NFPA 54; National Fuel Gas Code;...
  • Page 3: Table Of Contents

    OFP42 Table of Contents Cover..................................Warnings, Installations and Operations........................LP Cylinder Requirements............................Table of Contents..............................Locating Your Appliance............................Clearance Specifications............................INSTALLATION Pre-installation Questions and Answers......................... Important Information About Outdoor Fireplaces....................Framing Specifications............................Installation Clearances............................Gas Line Installation............................... Gas Specifications..............................Enclosures for LP (Propane) Gas Supply Systems....................ACCESSORIES Installing Brick Panels.............................
  • Page 4: Locating Your Appliance

    Locating Your Appliance Note: Ventilation and air flow comes from openings in the walls and ceiling. Open floor space around the appliance must not be considered ventilation and air flow space. This unit requires combustion air and will produce exhaust gases. Install in an open-air situation with natural ...
  • Page 5: Clearance Specifications

    * A fireplace shall not open directly above a sidewalk or paved driveway which is located between two single family The OFP42N and OFP42LP can be installed safely in a screened dwellings and services both swellings. porch area within the following guidelines:...
  • Page 6: Pre-Installation Questions And Answers

    Pre-installation Questions and Answers About curing of the paint -Operating Instructions- Your stove or fireplace has been painted with the highest quality silicone 1. Be sure to read and understand all the stove paint. This paint dries quickly in 15-20 minutes when first applied instructions in this manual before at the factory.
  • Page 7: Framing Specifications

    OFP42 - Framing Specifications -Fireplace and Framing Dimensions- *Attention: Top & Rear Standoffs must be folded into position & fastened with Screws before installation. (Dimensions allow for ½” in front of framing tabs for finishing materials.) Framing Clearances to Fireplace and Standoffs(Unless otherwise noted): Bottom: 0”/ Sides: 0”...
  • Page 8: Installation Clearances

    OFP42 - Installation Clearances Carefully follow the instructions below. This will ensure safe installation. Clearances: Warning Clearances from the firebox to adjacent wall   Improper installation, adjustment, alteration, service, or should not be less than 3-1/2 inches. maintenance can cause injury or property damage. Read Clearance from the top of the fireplace front to ...
  • Page 9: Gas Line Installation

    Massachusetts. This is in reference to the state of Massachusetts state code CMR238. IMPORTANT: Always check for gas leaks with a soap and water solution. DO NOT USE OPEN FLAME FOR LEAK TESTING. -Gas Specifications- OFP42N / OFP42NE / OFP42NE2 / OFP42LP / OFP42LPE / OFP42LPE2 / Models...
  • Page 10: Enclosures For Lp (Propane) Gas Supply Systems

    Enclosures for LP (Propane) Gas Supply Systems Combustible OFP42 WARNING TIPPING HAZARD Tank must be secured If you build an enclosure for an LP gas cylinder you must HOSE ROUTING: Hose must be follow these specifications. You must also follow local reasonable straight and free of codes.
  • Page 11: Installing Brick Panels

    OFP42 Installing Brick Panels Installing Brick Panels 1. Remove Brick Clips and Screws from inside Firebox Top. Remove Log Support. Do not discard these items. 2. Place Rear Brick Panel up against the back of the Firebox. 3. Tilt and slide Side Brick Panels into position in the sides of the Firebox.
  • Page 12: Stainless Steel Surround

    OFP42SS - Optional Stainless Steel Surround A Stainless Steel Surround is available as an option for the OFP42N/OFP42LP. (Install before finishing with decorative material on facing of enclosure.) Part 1: Preparing the Fireplace 1. Remove the 2 DT Screws inside the Firebox Top and remove the Deflector Hood from the top of the unit.
  • Page 13: Log F37

    Log F37 Installation for OFP42 #1: 1 Bag of Small 1/4” Lava Rock - Supplied with Unit #2: 1 Bag of Large 3/4" Lava Rock – Supplied #3: LOGF37 – Outdoor 7 Piece Burnt Oak Step #2 – Place Log 1 onto Rear Log Holder and up to Step #1 –...
  • Page 14: Mqrock

    MQROCK Setup for OFP42 Marquis (MQ) products are available through Marquis Dealers. Parts List #1: 1 Bag of Small 1/4” Lava Rock – Supplied with Unit #2: MQROCK 2 or 3 – Box of 30 Rocks MQROCK 3 shown below) #3: MQG10W or MQG10B –...
  • Page 15: Mqg10 (W-B) And Mqrock Setup

    MQG10 (W-B) and MQROCK Setup for OFP42 Marquis (MQ) products are available through Marquis Dealers. Parts List #1: 1 Bag of Small 1/4” Lava Rock – Supplied with Unit (Not Used for this Set-up) #2: MQROCK 2 or 3 – Box of 30 Rocks MQROCK3 shown below) #3: MQG10W or MQG10B –...
  • Page 16: Weather Cover

    OFP42WC -Weather Cover- An optional Weather Cover is available to protect the inside of the unit when not in use. Assembly Instructions 1. Insert Carriage Bolts through handles and into front of Fireplace Cover. 2. Place [2] washers and nut onto bolts on the back side of the Fireplace Cover.
  • Page 17: Electronic Spark Assist

    OFP42 Electronic Spark Assist – Option for Millivolt System Part Number #OFP42SA A Battery powered module is available to assist in lighting the pilot burner. See below for installation. Requires 1 AA Battery...
  • Page 18: Component Locations

    Component Locations – OFP42 Millivolt System – Top View REAR LOG HOLDER VALVE PILOT MAIN BURNER Gas line REMOTE RECEIVER (OPTION) IPI Proflame 1 System – Top View REAR LOG HOLDER PROFLAME 1 MODULE PILOT VALVE MAIN BURNER Gas line BATTERY BACKUP OR OPTIONAL REMOTE RECEIVER...
  • Page 19: Lighting Instructions - Millivolt

    OFP42 Millivolt Lighting Instructions 1. Remove Front Panel in order to access Igniter and valve controls. (To remove Access Panel, simply lift upward, and then pull forward.) 2. Refer to Millivolt Lighting Instructions below. Recommended Maximum Lead Length (Double Wire) When Using Wall Switch Wire Size Max.
  • Page 20: Burner System Maintenance

    Burner System Maintenance It is recommended to annually inspect and clean the Burner System to prevent malfunction and / or sooting. This operation should be performed by your dealer or a qualified technician. -CAUTION- Before servicing the burner system ensure that the gas supply is turned OFF and disconnect all electrical connections to the appliance.
  • Page 21: Gas Conversion - Pilot - Part B - Millivolt

    OFP42 Gas Conversion – Burner - Part A Warning! This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion, or production of carbon monoxide may result in causing property damage, personal injury or loss of life.
  • Page 22: Gas Conversion For Top Convertible Pilot - Part B - Ipi

    Gas Conversion for Top Convertible Pilot – Part B (series 0190XYZ) Instructions for converting SIT 190 series pilot burner injector from NG to PROPANE and from PROPANE to NG only. This information should be considered as supplemental to the Appliance Manufacturer's Instructions.
  • Page 23: Gas Conversion For Modulator - Part C

    Gas Conversion for Modulator – PART C...
  • Page 24: Lighting Instructions - Intermittent Pilot Ignition System (Ipi)

    - Lighting Instructions - Intermittent Pilot Ignition System (IPI) FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Always light the pilot whether for the first time or if the gas supply has run out with the glass door opened or removed.
  • Page 25: Ipi Electronic Ignition System

    Proflame 1 - IPI Electronic Ignition System - Overview IPI PF1 Box Cover The IPI system is an advanced burner controller that provides you with the option of having either a Standing-Pilot, or an intermittent igniting system. This alternating mode is controlled by the CPI/IPI Switch (Continuous Pilot Ignition/Intermittent Pilot Ignition) located on the IPI System Box.
  • Page 26: Ipi Proflame 1 Parts List

    Proflame 1 -IPI System Parts List- OFP42NE, OFP42NSE, OFP42LPE, OFP42LPSE 10. 1001-P168SI TC - Orifice Pilot LP 977.168 #35 (IPI) PART NO. DESCRIPTION 11. 1002-P012SI IPI Stepper Kit - LP 907.012 1006-P002SI Valve IPI Hi/Lo NG 1006-P003SI Valve IPI Hi/Lo LP 12.
  • Page 27: Operating The Receiver Without Batteries For Gt / Egt / Gtm / Egtm Remote Controls

    Operating the Receiver Without Batteries For GT / EGT / GTM / EGTM Remote Controls -Wiring Harness P/N 1002-P906si required for both IPI & Millivolt systems. -Millivolt Systems will also require Power Adapter P/N 1002-P850si. The Remote Receiver & IPI or Millivolt system can be powered by the AC Adapter. This is advantageous if you do not want to use batteries.
  • Page 28: Remote Control Operation - Ipi Proflame 1

    IPI Proflame 1 -Remote Control Operation- The Proflame GTM is configured to control the on/off main burner operation, its flame levels, and provides on/off and Smart *thermostatic control of the appliance. Transmitter Remote Receiver Transmitter Room *thermostat ( Transmitter Operation) The Transmitter is powered by 3 AAA type batteries.
  • Page 29: Ipi Proflame 2 Ifc Module And Remote Control

    IPI Proflame 2 IFC Module and Remote Control LCD Display ON / OFF Key Thermostat Key Batteries UP / DOWN Arrow Key Mode Key IFC Module Button Within 10 seconds press the button again until  Pairing Remote Control: you hear it beep. Install the 3 AAA type batteries in the battery bay, ...
  • Page 30: Ipi Proflame 2 Parts List

    Proflame 2 –NE2 / LPE2 -IPI System Parts List- OFP42NE2, OFP42NSE2, OFP42LPE2, OFP42LPSE2 IPI PROFLAME 2 - COMPONENT PARTS IPI - PF1 and PF2 Common Components PART NO. DESCRIPTION PART NO. DESCRIPTION 1005-P001SI Valve IPI Proflame PF2 885.001 NG - Stepper 13.
  • Page 32: Troubleshooting The Gas Control System

    OFP42 Troubleshooting the Gas Control System NOTE: Before troubleshooting the gas control system, be sure external gas shut off is in the “ON” position. Problem Possible Causes Corrective Action Spark igniter will not Defective or misaligned electrode at Check for spark at electrode and pilot: if no spark and light pilot.
  • Page 33: Parts List

    System (OFP42LP, OFP42LPS) Proflame IPI Valve, Wall Switch, Stainless 42OFP -BNGSI Burner Assembly- Natural Gas c/w Valve Steel Screens, Natural Gas, 55,000 BTU System (OFP42N, OFP42NS) OFP42NSE2 Outdoor Fireplace, Stainless Steel, SIT 42OFP -BLPSIE Burner Assembly- Propane c/w Valve Proflame 2 IPI Valve, Remote Control,...
  • Page 34 Valve IPI (NG; Hi/Lo) 1006-P002si Valve IPI (LP; Hi/Lo) 1006-P003si Pilot Assembly (LP) 1002-P047si Pilot Assembly (NG) 1002-P033si Pilot Burner Convertible NG – 24” 1002-PSEC7524 (Assembled) Spark Electrode (Long) 1002-P089si Electrode Flame Sensor (Long) 1002-P113si IPI Ignition Board 1002-P302si AC Wall Adapter 1002-P850si Battery Pack 1002-P12BH...
  • Page 35: Limited Warranty

    LIMITED WARRANTY Save this certificate. It gives you specific legal rights, and you may also have other rights which may vary from one province or state to another. In the event your unit needs servicing contact your dealer or contractor who installed or services your unit. When requesting service, please have the model and serial number from each unit readily available.

Table of Contents