CCL ELECTRONICS C6078A User Manual
  1. Manuals
  2. Brands
  3. CCL ELECTRONICS Manuals
  4. Weather Station
  5. C6078A
  6. User manual

CCL ELECTRONICS C6078A User Manual

Wi-fi weather station with 7-in-1 professional sensor
Hide thumbs
Table of Contents

Advertisement

Quick Links

WI-FI weather station with
7-In-1 professional sensor
Model: C6078A
User Manual

Advertisement

Table of Contents
loading

Related Manuals for CCL ELECTRONICS C6078A

Summary of Contents for CCL ELECTRONICS C6078A

  • Page 1 WI-FI weather station with 7-In-1 professional sensor Model: C6078A User Manual...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INTRODUCTION .

  • Page 3: Precautions

    PRECAUTIONS - Keep and reading the “User manual” is highly recommended . The manufacturer and supplier cannot accept any responsibility for any incorrect readings, export data lost and any consequences that occur should an inaccurate reading take place . - This product is designed for use in the home only as indication of weather conditions . This product is not to be used for medical purposes or for public information - Do not subject the unit to excessive force, shock, dust, temperature or humidity .

  • Page 4: Overview

    NOTE: This instruction manual contains useful information on the proper use and care of this product . Please read this manual through to fully understand and enjoy its features, and keep it handy for future use . OVERVIEW CONSOLE 11 12 13 14 15 16 22 23 1 .

  • Page 5: Wireless 7-In-1 Sensor

    WIRELESS 7-IN-1 SENSOR 1 . Antenna 2 . Rain collector 3 . UVI / light sensor 4 . Mounting pole 5 . Mounting base 6 . Balance indicator 7 . Wind vane 8 . Radiation shield 9 . Mounting clamp 10 .
  • Page 6 Step 2 Place the nut in the hexagon hole on the sensor, then insert the screw in other side and tighten it by the screw driver . Step 3 Insert the other side of the pole to the square hole of the plastic stand .

  • Page 7: Setup The Console

    MOUNTING GUIDELINES 1 . Install the wireless 7-IN-1 sensor at least 1.5m off the ground for better and more accurate wind measurements . 2 . Choose an open area within 150 meters from the LCD console . 3 . Install the wireless 7-IN-1 sensor as level as possible to achieve accurate rain and wind measurements .

  • Page 8: Synchronizing Additional Wireless Sensor(S) (Optional)

    NOTE: If no display appears on the LCD after you plug the adaptor, press [ RESET ] key by using a pointed object . SET LCD DISPLAY VIEWING ANGLE Press [ ] or [ ] key in normal mode to adjust LCD viewing angle to fit table stand or wall mount situation .

  • Page 9: Create Weather Server Account & Setup Wi-Fi Connection

    CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION The console can upload weather data to WUnderground and / or Weathercloud through WI-FI router, you can follow the step below to setup your device . NOTE: The Weather Underground and Weathercloud website are subjected to change without notice . CREATE WEATHER UNDERGROUND ACCOUNT 1 .

  • Page 10: Create Weathercloud Account

    5 . Jot down Your "Station ID" and "Station key" for the further setup step . CREATE WEATHERCLOUD ACCOUNT 1 . In https://weathercloud.net enter your information in "Join us today" section, then follow the instructions to create your account . NOTE: Use the valid email address to register your account .
  • Page 11 3 . Enter all the information in Create new device page, for the Model* selection box select the "W100 Series" under "CCL" section . For the Link type* selection box select the "SETTINGS", Once you have completed, click Create . 4 .

  • Page 12: Setup Wi-Fi Connection

    SETUP WI-FI CONNECTION 1 . When you power up the console for the fi rst time, the console LCD will show fl ashing "AP" and " " icon to signify that it has entered AP (Access Point) mode, and is ready for WI-FI settings .

  • Page 13: Setup The Weather Server Connection

    SETUP THE WEATHER SERVER CONNECTION Enter the following information into the below web interface "SETUP" page to connect the console to weather server, If you do not want to use Wunderground.com or Weathercloud.net, please empty the station ID & key to ignore the data upload . SETUP page SETTINGS Press "ADVANCED"...

  • Page 14: Advance Setting In Web Interface

    TIME SERVER CONNECTION STATUS After the console has connected to the Internet, it will attempt to connect to the Internet time server to obtain the UTC time . Once the connection succeeds and the console time has been updated, the “ ”...

  • Page 15: View Your Weather Data In Wunderground

    NOTE: - Calibration of most parameter is not required, with the exception of Relative Pressure, which must be calibrated to sea-level to account for altitude eff ects. VIEW YOUR WEATHER DATA IN WUNDERGROUND To view your weather station live data in a web browser (PC or mobile version), please visit http://www. wunderground.com, and then enter your “Station ID”...

  • Page 16: Other Setting & Functions Of The Console

    FIRMWARE UPDATE STEP 1 . Download the latest version firmware to your PC. 2 . Set the Console into AP (access point) mode then connect the PC to the console (ref to "SETUP WI-FI CONNECTION" section in previous page) . 3 .

  • Page 17: Activating Alarm And Temperature Pre-Alarm Function

    3 . Press [ ALARM ] key again to step the setting value to Minute with the Minute digit flashing. 4 . Press [ ] or [ ] key to adjust the value of the flashing digit. 5 . Press [ ALARM ] key to save and exit the setting . NOTE: - In alarm mode, the “...

  • Page 18: Temperature / Humidity Function

    TEMPERATURE / HUMIDITY FUNCTION - The temperature and humidity reading are display on the out and in / CH section . - Use the [ °C / °F ] slide switch to select the temperature display unit . - If temperature / humidity is below the measurement range, the reading will show “Lo” . If temperature / humidity is above the measurement range, the reading will show “HI”...
  • Page 19 TO SET THE WIND SPEED UNIT AND DIRECTION DISPLAY FORMAT 1 . In normal mode, press and hold [ WIND ] key for 2 seconds to enter into wind speed unit mode and the unit will flash. Press [ ] or [ ] key to change the wind speed unit in this sequence: m/s km/h...

  • Page 20: Weather Index

    75 ~ 88 km/h Some branches break off trees, and some 47 ~ 54 mph Strong gale small trees blow over . Construction / 41 ~ 47 knots temporary signs and barricades blow over . 20 .8 ~ 24 .4 m/s 89 ~ 102 km/h 55 ~ 63 mph Trees are broken off or uprooted,...

  • Page 21: Weather Forecast

    WEATHER FORECAST The built-in barometer continually monitor atmosphere pressure . Based on the data collected, it can predict the weather conditions in the forthcoming 12~24 hours within a 30~50km (19~31 miles) radius . Sunny Partly cloudy Cloudy Rainy Rainy / Stormy Snowy NOTE: - The accuracy of a general pressure-based weather forecast is about 70% to 75% .

  • Page 22: Light Intensity, Uv Index & Sunburn Time

    TO RESET THE TOTAL RAINFALL RECORD In normal mode, press and hold [ HISTORY ] key for 2 seconds to reset all the rainfall record . NOTE: To ensure to have correct data, please reset all the rainfall record when you reinstall your wireless 7-IN-1 sensor to other location .

  • Page 23: Past 24 Hours History Data

    TO CLEAR THE MAX/MIN RECORDS Press and hold [ MAX / MIN ] key for 2 seconds to reset the current on display MAX or MIN records . NOTE: The LCD will also display the " " / " ", " "...

  • Page 24: Back Light

    6 . Press [ ALERT ] key to shift to next alert reading . High / Low Alert off Alert on Alert on Alert off 7 . Press any key on the front side to save alert on /off status and back to normal mode, or it will automatically back to normal mode after 30 seconds without pressing any key .

  • Page 25: Wireless 7-In-1 Sensor Maintenance

    WIRELESS 7-IN-1 SENSOR MAINTENANCE REPLACE THE WIND CUP 1 . Remove rubber cap and Unscrew CLEANING THE RAIN 2 . Remove the wind cup for COLLECTOR replacement 1 . Rotate the rain collector by turning it 30°anti-clockwise . CLEANING THE UV SENSOR 2 .

  • Page 26: Specification

    Temperature reading too 1 . Place the sensor in open area and at least 1.5m off the ground. high in the day time 2 . Make certain that the sensor array is not too close to heat generating sources or strictures, such as buildings, pavement, walls or air conditioning units .
  • Page 27 Indoor Temperature (Note: Data detect by console) Temperature unit °C and °F <0°C or >40°C ± 2°C (<32°F or >104°F ± 3 .6°F) Accuracy 0~40°C ±1°C (32~104°F ± 1 .8°F) Resolution °C / °F (1 decimal place) Memory modes Historical data of past 24 hours, daily Max / Min Indoor Humidity (Note: Data detect by console) Humidity unit...

  • Page 28: Wireless 7-In-1 Sensor

    LIGHT INTENSITY (Note: Data detect by 7-in-1 sensor) Light intensity unit Klux, Kfc and W/m² Display range 0 ~ 200Klux Resolution Klux, Kfc and W/m² (2 decimal place) Memory modes Historical Data of past 24 hours, Max Weather Index (Note: Data detect by 7-in-1 sensor) Weather index mode Feels like, Wind Chill, Heat Index and Dew point Feels like display range...

Table of Contents