Manually Setting Up The Network Address; Hm196 (E/F) Web 213:276 - Toshiba 62HM196 User Manual

HM196_EN.book Page 58 Tuesday, May 30, 2006 2:18 PM
5
The message "Obtain network address automatically?"
will display. Highlight Yes and press T.
Basic Network Setup
Obtain network address automatically?
Yes
6
The message "Please wait..." will display while the TV is
attempting to load the network address information from
the DHCP server.
Basic Network Setup
If the automatic network address setup is successful,
go to step 7.
If the automatic network address setup is not
successful, go to step 8.
7
If the automatic network address setup is successful, the
following screen will appear:
Basic Network Setup
Done! Network address information has been found!
a) Press T to close the screen and return to the Network
menu.
b) Skip to section C, "Setting up file sharing on your PC"
(- page 59).
8
If the automatic network address setup is not successful,
the following screen will appear:
a) Make sure all cables for your home network are
securely connected.
b) Make sure your home network is set up properly. See
the Installation Guide for TV connection
information. Also consult the owner's manuals for
your other components.
c) Make sure the DHCP and security settings on your
home router are correct. Consult the owner's manual
for your router.
d) Retry the automatic network address setup by following
these steps:
(1) Highlight OK and press T.
(2) Repeat steps 1–6. (If you have already repeated
this setup process, go to step 9.)
58
Chapter 7: Using the THINC
No
Please wait...
Exit
™ home network feature
9
If, after repeating steps 1–6, you receive the error
message shown in step 8:
Either...
a) Highlight "OK" and press T.
b) Go to "Manually setting up the network address".
Or...
a) Highlight "OK" and press T.
b) Continue to sections C, D, and E (- pages 59–66)
(to set up and use file sharing) and/or to sections F and
G (- pages 67–75) (to set up and use e-mail
scheduling).
If the file sharing and/or e-mail scheduling features
work correctly, then the automatic network address
setup was successful (even though the TV displayed the
error message).

Manually setting up the network address

This setup requires the data listed below. You can get this
data from either your ISP or the configuration utility for
your DSL/cable modem or router.
IP address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Subnet mask:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Gateway (Router) address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
DNS (Domain Name Server) address:
___ ___ ___ . ___ ___ ___ . ___ ___ ___ . ___ ___ ___
Press Y and open the Setup menu.
1
Highlight Installation and press T. The Installation
2
menu appears.
3
Open the Network menu.
Highlight Basic Network Setup and press T.
4
5
The message "Obtain network address automatically?"
appears.
Highlight No and press T.
Basic Network Setup
Obtain network address automatically?
Yes
6
The Basic Network Setup menu appears.
Press B or b to highlight the IP Address field, and then
use the Number buttons on the remote control to input the
IP address.
Basic Network Setup
Please enter your Network Address Information
IP Address
Subnet Mask
Gateway (Router)
DNS (Domain Name Saver)
Cancel
7
Press b to highlight the Subnet Mask field, and then use
the Number buttons to input the Subnet Mask.
No
0 0 0 0
225 225 225 0
0 0 0 0
0 0 0 0
Done

HM196 (E/F) Web 213:276