Related Manuals for King Canada KC-15CM-2
Summary of Contents for King Canada KC-15CM-2
- Page 1 3.5 CUbIC fEET pORTAbLE CEMENT MIxER 02/2015 INSTRUCTION MANUAL MODEL: KC-15CM-2 COPYRIGHT © 2014 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
King Canada service center. Contact your retailer or visit our web site at www.kingcanada.com for an updated listing of our authorized service centers. In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period. - Page 3 GENERAL & SpECIfIC SAfETY INSTRUCTIONS VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that for the specified tool can result in SERIOUS IN- JURY to the user - as well as damage to the tool.
- Page 4 9. On/Off switch with removeable key 4. Lifting handle (1 of 2) 10. Motor housing & cover 5. Frame 11. Upper drum 6. Lower drum 12. Mixing paddle (1 of 2) MODEL KC-15CM-2 Drum capacity 3.5 cu.ft. Drum opening 15” Drum speed 36 RPM Motor...
-
Page 5: Electrical Information
ELECTRICAL INfORMATION WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SE- RIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE CEMENT MIxER DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! pOWER SUppLY 120V GROUNDED OUTLET CURRANT... - Page 6 ASSEMbLY UNpACKING Due to modern mass production techniques, it is unlikely that your King Canada cement mixer is faulty or that a part is missing. If you find anything wrong, do not operate until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
- Page 7 ASSEMbLY Assembling Tilt Lever 1. Install the tilting lever angle control plate (A) Fig.7 to the support bracket shaft (B) using 2 short hex. bolts, washers and spring washers (C). fIGURE 7 2. In order to install the tilting lever assembly, first locate the tilting lever (A) Fig.8 and insert spring (B) inside the tilting lever.
- Page 8 ASSEMbLY Assembling V-belt 1. Position the V-Belt (A) Fig.11 around the motor pulley (B) and then over the drum pulley (C). It may be neccessary to lift the motor plate in order to place V-belt around the pul- leys. Then push the motor inward until it is directly under the drum pulley. Tighten the motor hardware to secure the motor.
-
Page 9: Assembly And Operation
ASSEMbLY & OpERATION Assembling Drum Gasket & Upper Drum Cover 1. Place the rubber gasket (A) Fig.15 onto the lower drum (B) as shown. Line up the rubber gasket mounting holes with the ones on the lower drum. It is recommended to use a gasket sealer (not included) to fix the rubber gasket to the lower drum. -
Page 10: Maintenance And Troubleshooting
MAINTENANCE & TROUbLESHOOTING MAINTENANCE 1. Place the cement mixer on a solid, even and level surface. 2. Connect the power cord to an electric outlet (or properly rated grounded three prong extension cord). 3. Before each use, inspect the general condition of the cement mixer. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, damaged or cracked V-belt, and any other condition that may affect its safe operation.