Page 1
® Satellite User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 207 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 2
If you fail to do so, this product may not function properly and you may lose data or suffer other damage. TOSHIBA AMERICA INFORMATION SYSTEMS (“TOSHIBA”), ITS AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE.
Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's or expansion unit's serial port, monitor port, USB port, PS/2 ®...
Industry Canada Requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. FCC Requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems.
If trouble is experienced with this equipment, for repair or warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B), as defined and approved by the Institute of Electrical and Electronics Engineers.
Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
des fenetres afin de Fournier un ecram de blindage maximal. Si le matriel (ou son antenne d'emission) est installe a l'exterieur, il doit faire l'objet d'une licence. Europe – EU Declaration of Conformity ❖ This device complies with the essential requirements of the R&TTE Directive 1999/5/EC with essential test suites as per standards: EN 60950 Safety of Information Technology equipment ETS 300 328 Technical requirements for radio equipment...
This device must accept any interference that may cause undesired operation. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA.
Page 11
Caution: Exposure to Radio Frequency Radiation The Toshiba Wireless LAN Mini PCI Card will be installed with one of two types of antennas. The both of antenna types, when installed are located at the upper edge of the LCD screen.
Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.
It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916 Fax: 03-5444-9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and...
Page 14
❖ Consult the dealer or an experienced radio/TV technician for help. Toshiba is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this Toshiba Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by Toshiba.
Page 15
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Approved Countries/Regions for use for the Intel Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in...
LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth™ cards from TOSHIBA, always change the frequency, move your PC to the area outside of the interference range of 2.4 GHz Wireless LAN devices (40 meters/43.74 yards or more) or stop transmitting from your PC.
If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment. Regulatory statements This product complies with any mandatory product specification in any country/ region where the product is sold.
Page 19
The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 20
This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 21
Device Authorization This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan. The Name of the radio equipment: EYXF2CS TELECOM ENGINEERING CENTER Approval Number: 01NYDA1305 The following restrictions apply:...
This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 23
Dolby - Manufactured by Toshiba under license from Dolby Laboratories/Dolby and the double-D symbol are trademarks of Dolby Laboratories. Bluetooth is a trademark owned by its proprietor and used by Toshiba under license. All other brand and product names are trademarks or registered trademarks of their respective companies.
Keeping yourself comfortable ...38 Precautions...41 Setting up your computer ...43 Setting up your software...43 Registering your computer with Toshiba ...45 Adding external devices ...45 Connecting the AC adapter...46 Charging the main battery...48 Using the computer for the first time ...49...
Page 25
Turning on the power...50 Using the TouchPad™...51 Control buttons...51 Disabling or enabling the TouchPad ...52 Installing additional memory (optional) ...53 Removing a memory module...56 Connecting a mouse ...57 Connecting a printer ...57 Setting up a printer ...58 Using the Add Printer Wizard...58 Turning off the computer ...61 Caring for your computer...62 Cleaning the computer...62...
Page 26
Starting again from Hibernation mode ...90 Using Stand By ...91 Going into Stand By mode more quickly...91 Starting again from Stand By...92 Toshiba’s online resources ...92 Chapter 3: Mobile Computing... 93 Toshiba’s energy-saver design...93 Running the computer on battery power ...93 Power management ...95...
Page 27
Taking care of your battery ...103 Maximizing battery life...104 Disposing of used batteries safely ...105 Traveling tips ...105 Chapter 4: Getting to Know the Windows Operating System... 107 Lesson 1: Exploring the desktop ...108 Finding your way around the desktop ...108 Windows Lesson 2: Using the TouchPad and control buttons together ...111...
Page 28
Contents Chapter 5: Getting to Know the Windows Media Center Edition... 135 Media Center Setup...136 Connecting to a Television ...136 Connecting the TV Signal Source When You Have an Existing Setup...137 Connecting the External Remote Sensor...138 Connecting the VCR or Set Top Box to the Computer ...139 Starting the Media Center ...140 Remote Control For Media Center...143...
Page 29
Displaying Your Pictures...168 Viewing a Slide Show...170 Sorting your Pictures...170 Watching Your Digital Movies...170 Organizing Your Videos ...171 Playing Digital Videos ...172 Playing a Video in Full Screen Mode ...173 Sorting Videos ...173 Watching a DVD...173 Stopping a DVD Movie...174 Playing a DVD movie already in your drive ...175 Changing the Media Center Settings ...175 Chapter 6: Exploring Your Options...
Page 30
Contents Signing up with an Internet Service Provider ...195 Surfing the Internet...196 Internet features...196 Uploading and downloading files on the Internet... Exploring video features...197 Changing the display properties setting ...198 Display settings hot key ...199 Exploring audio features ...199 Recording sounds...199 Using a microphone...199 Adjusting recording settings ...200 Using external speakers or headphones ...201...
Page 31
Modem problems...230 Develop good computing habits ...230 If you need further assistance...232 Before you call ...232 Contacting Toshiba ...233 Other Toshiba Internet Web sites ...234 Toshiba’s worldwide offices ...234 Appendix A: Hot Keys...238 Instant password security...238 Without a password...238 With a password ...238 Maintaining security when the battery is not fully charged...239...
Page 32
Contents Appendix B: Power Cable Connectors... 245 Appendix C: Using ConfigFree™ with your Toshiba Computer... 246 Getting Started...247 ConfigFree Main Screen...247 Starting ConfigFree ...248 Configuring ConfigFree ...248 ConfigFree Utilities...249 Connectivity Doctor ...249 Device Settings ...250 Profile Settings ...252 Quick Connect...253 Using Auto Switch ...254...
Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
Toshiba's Web site at pcsupport.toshiba.com. While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice.
the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Service options Toshiba offers a full line of service options built around its SelectServ the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com.
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations.
AC power source, and let it dry out completely before turning it on again. If the computer does not operate correctly after you turn it back on, contact a Toshiba Authorized Service Provider. Keeping yourself comfortable Strain and stress injuries are becoming more common as people spend more time using their computers.
Page 39
❖ If you are using an external monitor, the top of the display should be no higher than eye level. ❖ If you use a paper holder, set it at about the same height and distance as the screen. Seating and posture When using your computer, maintain good posture with your body relaxed and your weight distributed evenly.
Page 40
Getting Started Selecting a place to work ❖ Adjust the back of your chair so that it supports the lower curve of your spine. If necessary, use a cushion to provide extra back support. Lower-back-support cushions are available at many office supply stores. ❖...
Work habits The key to avoiding discomfort or injury from strain is to vary your activities. If possible, schedule a variety of tasks into your working day. Finding ways to break up the routine can reduce stress and improve your efficiency. ❖...
Page 42
Getting Started Selecting a place to work ❖ Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is being used. Overheating of a PC Card can result in errors or instability in its operation.
Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” on page 43 or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards.
Page 44
A window will display asking if you wish to register with Toshiba and Microsoft. Click Yes to register or No to exit the process. If you click No, you may register with Toshiba by clicking the NOTE Register with Toshiba icon on the desktop.
If you opt not to register at that time, you can either double-click the icon on your desktop or go to the Toshiba web site at www.register.toshiba.com. Customer failure to complete Product Registration will not diminish Customer rights under this limited Warranty.
Getting Started Connecting the AC adapter Connecting the AC adapter Your computer requires power to operate. Use the power cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery. Power cable Power cable and AC adapter Hold the power cable by its plug when you connect/disconnect it.
Page 47
Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Getting Started Charging the main battery Connecting the AC adapter to the computer Connect the power cable to a live electrical outlet. The AC power and battery lights glow. Damaged power cables can cause fire or electric shock. Never modify, forcibly bend, place heavy objects on top of, or apply heat to the power cable.
Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time. Continuing to charge a fully charged battery can damage the battery. Battery life and charge time may vary depending on the NOTE applications, power management settings, and features used.
Getting Started Using the computer for the first time Small bright dots may appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
Using the TouchPad The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: ❖...
Getting Started Using the computer for the first time The function of the secondary (right-hand) button depends on the program you are using. It usually corresponds to the right mouse button. Check your program’s documentation to find whether it uses the right mouse button. Disabling or enabling the TouchPad The TouchPad is enabled by default.
Toshiba Web site at pcsupport.toshiba.com). There are two memory slots. Your system may have both slots occupied.
Page 54
Getting Started Installing additional memory (optional) The operating system turns off the computer. Unplug and remove any cables connected to the computer. Close the display panel and turn the computer upside down to locate the expansion memory slot cover. Memory slot cover Base of a Satellite P25 series computer Using a standard Phillips no.
Page 55
Installing additional memory (optional) Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer).
Getting Started Installing additional memory (optional) Replace the expansion memory slot cover. Replace the screws and tighten them. Turn the computer over and reconnect any cables you removed. Turn on the computer. To verify that the computer correctly recognizes the memory, click Start, Control Panel and click Performance and Maintenance.
Complete the procedure by following steps 10 through 12 “Installing additional memory (optional)” on page Connecting a mouse You may want to use a mouse instead of the TouchPad, the computer’s built-in pointing device. To connect a USB mouse, plug the mouse cable into one of the USB ports.
Getting Started Connecting a printer To connect a USB printer: Plug the USB connector into one of the USB ports on your computer Plug the printer’s power cable into a live AC outlet. See your printer documentation for additional configuration steps, or see “Setting up a printer,”...
Page 59
Sample Printers and Faxes window Click Add Printer. The Add Printer Wizard starts. Sample Add Printer Wizard Click Next. Getting Started Connecting a printer...
Page 60
Getting Started Connecting a printer The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual. If the printer you are setting up: ❖...
The operating system prompts you to print a test page. If your printer is connected and turned on, click Next. To complete the setup procedure without printing a test page, click No, and then click Next. Click Finish. You are now ready to print. Depending on your program, you may see various messages indicating the status of your print job.
Cleaning the computer To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. Keep liquid, including cleaning fluid, out of the computer’s keyboard, speaker grille, and other openings.
To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. Using a computer lock You may want to secure your computer to a heavy object such as your desk.
Page 64
Getting Started Caring for your computer Insert the cable’s locking end into the security lock slot, then rotate the key a quarter turn and remove it. The computer is now securely locked to deter computer theft. Locking the computer...
Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working.
Learning the Basics Using the keyboard ❖ Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable.
Learning the Basics Using the keyboard ® Windows special keys ® Windows special keys The keyboard provides two keys that have special functions in the operating system: ❖ The Windows ❖ The Application key has the same function as the secondary TouchPad control button (or secondary mouse button).
Page 69
Using the numeric keypad overlay To turn on the numeric keypad overlay, press simultaneously. The numeric mode light on the keyboard indicator panel glows when the numeric overlay is on. You can still use the overlay keys to type alphabetic characters while the numeric overlay is on.
Learning the Basics Starting a program To turn off the cursor control overlay, hold down the and press keyboard indicator panel goes out. Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer.
To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name.
Learning the Basics Backing up your files Backing up your files Backing up your files means copying individual files to media, such as CD, or copying entire sections of your hard disk to another device, such as a tape drive. For those systems with a floppy disk drive, you may back up file to a floppy disk as follows: To back up to a CD or other media, insert the media into...
Using the DVD-ROM or Multifunction drive If a DVD-ROM drive or Multifunction drive is not currently installed in the modular bay, follow the instructions in the Modular Bay” on page TECHNICAL NOTE: Your DVD-ROM or multi-function drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region.
Learning the Basics Using the DVD-ROM or Multifunction drive DVD-ROM drive components Your DVD-ROM drive may look like this: Eject button Manual eject hole Sample DVD-ROM drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive.
Learning the Basics Using the DVD-ROM or Multifunction drive CD/DVD control buttons The control buttons on the front edge of the computer allow you to play audio CDs when the computer is off. You can also use them to play CDs and DVDs when the computer is on. Stop/eject Mode Play/pause...
Learning the Basics Using the DVD-ROM or Multifunction drive CD/DVD control and digital audio modes The following chart describes CD/DVD control and digital audio mode. Power is off and you press Play/Pause While in CD/DVD mode, you press the mode button Operating system is running and you press Play/Pause...
Using the DVD-ROM or Multifunction drive Inserting a disc Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears. To turn the volume down, use the Volume Control switch or access the Volume Control program (click Start, All Programs, Accessories, Entertainment, and then Volume Control).
Page 78
Learning the Basics Using the DVD-ROM or Multifunction drive Inserting a disc Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction. Gently press the center of the disc onto the spindle until it locks into place.
Learning the Basics Using the DVD-ROM or Multifunction drive Playing an audio CD Insert an audio CD and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD, select the Play Audio CD using Windows Media Player option and click OK.
Page 80
Learning the Basics Using the DVD-ROM or Multifunction drive Rewind Play Stop Previous track Next track Mute Sample Windows Media™ Player screen The Windows Media an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel.
Using the DVD-ROM or Multifunction drive Viewing the contents of a CD or DVD CDs and DVDs contain files just like the hard disk. CDs are often used to install software or store files that require lots of space, such as photographs and large presentation files. You can use Explorer or My Computer to view the contents of any CD or DVD.
Learning the Basics Using the DVD-ROM or Multifunction drive Removing a disc with the computer off Insert a slender object, such as a straightened paper clip, into the manual eject button access hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.
Microsoft To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. Connecting the modem to a phone line Your computer comes with a built-in modem. To use the modem, you must connect it to a standard voice-grade RJ-11 telephone line.
Learning the Basics Powering down the computer the telephone number for the dial-up connection. To set up the network connection, use the Dial-Up Networking Wizard: Click Start and point to All Programs. Point to Accessories, then to Communications. Click Network Setup Wizard or Network Connections.
Using Shut Down For the Windows steps to shut down the computer: Click the Start button, then Shut Down. The Shut Down Windows dialog box appears. Select Shut Down from the drop-down list. Click OK. The computer shuts down completely. Holding the NOTE dialog box is open, changes the Stand By button to Hibernate.
Learning the Basics Using Shut Down ❖ Restarting from Hibernation mode uses less time and battery power than restarting from Shut Down. ❖ Restarting from Hibernation mode uses a little more time and battery power than restarting from Stand By because information is being retrieved from the hard disk instead of memory.
You can also turn off the computer by pressing the power button or closing the display panel. To use either of these methods, you first need to turn on the feature in the Toshiba Power Management Utility. Click Start, Control Panel, then Performance and Maintenance.
Learning the Basics Using Hibernation Sample Toshiba Power Management Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again after Shut down To start the computer up again, press and release the power button. The on/off light turns on.
Page 89
Click Start, Control Panel, then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Advanced tab, and select the options you want. ❖ When I press the power button...
Learning the Basics Using Hibernation Sample Toshiba Power Management Advanced tab Click Apply. Click OK, then close the Control Panel. Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using.
You can also specify an amount of time after which the computer automatically goes into Stand By mode. To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility. Learning the Basics Using Stand By...
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades.
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods while traveling.
Page 94
Toshiba Web site at pcsupport.toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged.
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s Global Support Centre. Charging the battery Battery charge time may vary depending on the applications, NOTE power management settings, and features used.
Mobile Computing Charging the battery The battery may not start charging immediately if: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature (50 degrees to 80 degrees Fahrenheit, 10 degrees to 26 degrees Celsius).
The above error message may vary by computer model. NOTE The RTC battery does not charge while the computer is turned off even when the AC adapter is charging the computer. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working.
The current power source and battery power remaining section displays the current charge state of the battery. The value displays as a percentage of remaining battery charge. Click the Battery Power Meter tab. Sample Toshiba Power Management Battery Power Meter tab...
Toshiba’s power-saving options greatly increase the length of time you can use the computer before it becomes necessary to recharge the battery. Toshiba has combined these options into preset power usage modes. What to do when the battery runs low When the battery runs low you can ❖...
To set an alarm: Click Start, Control Panel, and then Performance and Maintenance. Double-click the Toshiba Power Management icon. Click the Alarm tab and set the alarm, as desired.
Sample Toshiba Power Management Alarm tab Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short- circuit its terminals.
Page 102
Mobile Computing Changing the main battery Slide the battery lock forward to unlock the battery pack. Push and hold the battery release latch. Releasing the battery While still holding the release latch in the open position, gently slide the battery pack out of the computer. Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the...
Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through toshiba.com. ❖ Reverse Polarity should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity.
Mobile Computing Taking care of your battery Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: Turn off the computer’s power.
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the Mobile Computing Disposing of used batteries safely 37, also apply while traveling.
Page 106
They all provide plenty of extra space for manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information. TECHNICAL NOTE: When traveling by air, you may be required to pass your notebook through airport security equipment. The...
Chapter 4 Getting to Know the Windows System This chapter introduces the Windows by guiding you through a few basic tasks. If you have used a Windows will find the Windows Whether you have used a Windows the skill and confidence you will gain from this chapter will more than offset the short amount of time spent going through these lessons.
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop Lesson 1: Exploring the desktop The desktop is the launching pad for everything you can do in the Windows start programs, find documents, set up system components, and perform most other computing tasks.
Page 109
The icons initially displayed on your system desktop include: Toshiba Access—Opens a window with links to software updates, services and support, and other important benefits. Recycle Bin—Holds files you have deleted using the Windows Explorer.
Getting to Know the Windows ® XP Operating System Lesson 1: Exploring the desktop Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open.
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Computers can be connected together to form a network, so that programs, documents and other data can be quickly and easily shared between computers. You can use the My Computer feature on the Start menu to access any file in the Windows For more information, read the Microsoft documentation that...
Page 112
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Sample desktop shortcut menu Click an empty area to close the shortcut menu. Use the TouchPad to move the pointer to the Start button.
Page 113
Getting to Know the Windows ® XP Operating System Lesson 2: Using the TouchPad and control buttons together Click an empty area of the taskbar at the bottom of the screen and, while holding down the primary button, use the TouchPad to drag the pointer to the right edge of the desktop, then release the primary button.
Getting to Know the Windows ® XP Operating System Lesson 3: Learning about the Internet Lesson 3: Learning about the Internet This lesson demonstrates how to access a Web page from a window and from the taskbar. The lesson assumes you have an account with an Internet Service Provider (ISP).
Getting to Know the Windows ® XP Operating System Lesson 4: Creating a new document This lesson teaches you how to create a text file without having to first open a program. Move the pointer to an empty area of the desktop, then click the secondary button.
Getting to Know the Windows ® XP Operating System Lesson 5: Creating a new folder Lesson 5: Creating a new folder DEFINITION: A folder is an area where you can store documents and other types of files. It is analogous to a file folder stored in a file cabinet.
Getting to Know the Windows ® XP Operating System Close the window by clicking its Close button and continue with the next lesson to learn how to start programs. Lesson 6: Starting programs Usually, you will know which program you want to use for a particular task.
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows The operating system opens Windows Explorer, which provides access to all your computer’s resources. For example, it lets you see all the files in a particular folder on the computer’s hard disk.
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows You can also hide windows by removing them from the desktop without actually closing your document or program. This lesson introduces several ways to adjust the size, shape, and position of windows open on the desktop.
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Windows Explorer disappears from the desktop. However, it is still open, as you can see from the taskbar. HINT: Minimizing program windows is a good way to clean up the desktop without actually closing programs.
Page 121
Getting to Know the Windows ® XP Operating System Lesson 7: Resizing, repositioning, and hiding windows Click the title bar of the Paint window and drag it to the left side of the desktop. You can move any window by clicking its title bar and dragging it.
Getting to Know the Windows ® XP Operating System Lesson 8: Closing programs Lesson 8: Closing programs Once you are finished working with a document or program, it is a good idea to close it. While you can run several programs at the same time, having a large number of programs and documents open simultaneously can slow down your computer.
Getting to Know the Windows ® XP Operating System Move the pointer to an empty area of the desktop, then click the secondary button. The operating system displays the desktop shortcut menu. Click New, then click Shortcut. The operating system displays the Create Shortcut dialog box.
Page 124
Getting to Know the Windows ® XP Operating System Lesson 9: Creating shortcuts Sample Search options on the Start menu Click All Files and Folders. The operating system displays the Search Results dialog box. Sample Search Results dialog box HINT: Search also allows you to perform searches on the Internet.
Getting to Know the Windows ® XP Operating System Type char and then click Search. The operating system displays a list of all the files with “char” in their names. Click the Character Map file with the secondary button and drag it to the desktop. A shortcut menu appears.
Page 126
Getting to Know the Windows ® XP Operating System Lesson 10: Changing the screen saver This lesson introduces object properties by showing you how to change one of the properties of the desktop—the screen saver. This is a continuously changing pattern that appears on the screen during pauses in your work.
Getting to Know the Windows ® XP Operating System To apply a pattern to your desktop, click Apply. After you have chosen a screen saver pattern and applied it to your desktop, click OK. The operating system returns you to the desktop. You can view any object’s properties by clicking the object with the secondary button, then choosing Properties from the shortcut menu that appears.
Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop HINT: To open the Date and Time Properties dialog box more quickly, either click the time display on the taskbar with the secondary button, then click Adjust Date and Time, or double- click the time display.
Page 129
Getting to Know the Windows ® XP Operating System Lesson 12: Removing objects from the desktop Double-click the Recycle Bin icon. The operating system opens the Recycle Bin window. Notice that all the icons you dropped on the Recycle Bin are listed.
Getting to Know the Windows ® XP Operating System Lesson 13: Using System Restore To delete everything from the Recycle Bin at once, choose Empty Recycle Bin from the File menu. Click Yes to confirm that you are sure. HINT: Empty the Recycle Bin periodically. Even though an item is moved to the Recycle Bin, it still uses valuable space on the hard disk drive until it is deleted from the Recycle Bin.
Getting to Know the Windows ® XP Operating System The operating system guides you through the process of storing your system settings for future use. It also guides you through restoring your system to the selected date or time. Lesson 14: If I am lost, what do I do? This lesson teaches you how to use some of the Help and Support features in Windows ®...
Page 132
Getting to Know the Windows ® XP Operating System Lesson 14: If I am lost, what do I do? The left side of the screen contains the index. The text box above the index, where the cursor is flashing, lets you type in a topic you want to find in the index.
Getting to Know the Windows ® XP Operating System program to look at it while you read about the program in the Help topic. Using the online tours and tutorials Whether you are new to computers or you have some experience, the Windows is a good place to start.
Getting to Know the Windows ® XP Operating System Lesson 15: Turning off your computer Lesson 15: Turning off your computer It is very important that you let the Windows system shut down your computer. As it shuts down, the operating system performs a number of tasks that ensure that everything is in place the next time you turn on the computer.
Chapter 5 Getting to Know the Windows Center Edition This section introduces you to the Windows Media Center Edition, a complete multimedia center where you can play your entire library of audio, video, and picture media on your computer, using either your computer’s keyboard, mouse, or the remote control.
Getting to Know the Windows ® XP Media Center Edition Media Center Setup Media Center Setup This section shows you how to set up your computer to use the Media Center. Connecting to a Television Your computer has TV-out capability, meaning you can connect it to a television and view the computer image on the television.
Getting to Know the Windows ® XP Media Center Edition Connecting the TV Signal Source When You Have an Existing Setup This section describes how to connect the signal source from the wall to a VCR to a TV using coaxial cable. Remove the coaxial cable from the VCR input, and connect it to the input of a coaxial cable signal splitter (not shipped with your computer or system).
Getting to Know the Windows ® XP Media Center Edition Media Center Setup Existing setup Wall Cable Coaxial cable Set-top box/ satellite In Set-top box/ satellite Out Coaxial cable VCR In VCR Out Coaxial cable TV In Sample wall-to-VCR-to-TV setup Connecting the External Remote Sensor The external IR remote sensor is a small device that connects to the computer and allows the remote control to work with...
Getting to Know the Windows ® XP Media Center Edition Sample IR receiver with cables attached Position the end of the IR receiver cable over the remote IR receiver window on your cable TV set-top box or VCR. Peel off the adhesive backing on the IR remote sensor and mount the sensor within 5 inches of the set top box or VCR.
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Starting the Media Center To start the Media Center: ❖ Click Start, and then click Media Center. You can also point the remote control at the remote sensor and press the Start button.
Page 141
Getting to Know the Windows ® XP Media Center Edition Media Center Setup Wizard To complete the Media Center Setup, follow the wizard on- screen prompts. When the wizard finishes, the Media Center main window displays. You can run Media Center side by side with other Windows NOTE software programs.
Page 142
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Sample Media Center main window The Media Center main window is the central point for controlling all Media Center features. With a quick click of the mouse or using your remote control, you can: ❖...
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Use the Media Playback controls at the bottom of the screen to control your movies, music, and photo displays. Channel up and down Play Replay, Rewind (Previous) Stop Record Skip, Fast Forward (Next)
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Using the remote control, you can: ❖ Navigate and control all Media Center windows. ❖ Control the video or live TV display. ❖ Place the computer in and out of Stand By mode. The remote control can send a strong signal to the remote sensor from within a range of about 26 feet and from an angle of about 45 degrees.
Page 145
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center The remote control has the following buttons/functions: Stand By — Puts the computer into a power reduced Stand By state. Record — Records the selected television program and stores it on your hard disk.
Page 146
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center More Info — The button provides more details on a TV program that is listed in the Guide. My Videos — Opens the My Videos window. My Music —...
Page 147
Getting to Know the Windows ® XP Media Center Edition ❖ Navigation and other direct access — The navigation buttons move the cursor around Media Center windows and select desired actions, much like a mouse does. The other direct access buttons open specific windows within the Media Center, such as the Television Program Guide, a DVD main menu, and live TV in full screen mode.
Page 148
Getting to Know the Windows ® XP Media Center Edition Starting the Media Center Use Pause to pause selected media. Press Pause and then FWD repeatedly to play media frame by frame in slow motion. To continue slow motion, you must press the FWD button more than once.
Page 149
Getting to Know the Windows ® XP Media Center Edition Use Stop to stop selected media from playing. When this is pressed while you are watching TV, the Media Center pause buffer continues to record in the background. Use Skip to move forward in the selected audio or video file. ❖...
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs Watching Television Programs Before you can watch TV using Media Center, make sure your NOTE computer is set up correctly for your TV signal source and that you have completed the Media Center setup wizard.
Page 151
Getting to Know the Windows ® XP Media Center Edition Sample MY TV screen To watch a television program: Press the TV button on the remote control. The last channel selected or the first channel available begins playing next to the My TV menu. Select a channel by using the Channel/Page (+ or -) buttons or by using the numeric buttons on the remote control.
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs Selecting a Program from the TV Guide In the TV Guide, you can scroll through a list of the current television programs and channels available from your television service provider.
Getting to Know the Windows ® XP Media Center Edition Sample TV Guide screen ❖ Use the arrows at the top of the screen to display programs for later or earlier in the day. ❖ Use the arrows at the bottom of the screen to display additional channels available for viewing.
Getting to Know the Windows ® XP Media Center Edition Watching Television Programs click Start, and then My TV, and then select Recorded ❖ All of your recorded TV programs display on the Recorded TV screen. You can sort your programs by Date, Category, or Name by clicking the desired sort option.
Getting to Know the Windows ® XP Media Center Edition Select Play in the window, and then press OK on the remote control to begin watching the program in full screen mode. If the show is not currently playing, select Record Show or Record Series, and then press OK.
Getting to Know the Windows ® XP Media Center Edition Recording TV your show is being recorded, you can select TV Guide. The Record icon should appear next to the show in the TV Guide while you are recording. The Record icon disappears when the recording is complete.
Getting to Know the Windows ® XP Media Center Edition Recording from the Guide To record a current or future show or series from the Guide: Press the Start button on the remote control, select My TV, and then select Guide. Use the arrow buttons on the remote control to find the show you want to record, select the show, and then press You can also press the numeric buttons on the remote...
Getting to Know the Windows ® XP Media Center Edition Recording TV Use the arrow buttons to scroll through the search results to select the show you want to record, select the show, and then press OK. Select Record or Record Series in the window, and then press OK.
Getting to Know the Windows ® XP Media Center Edition Select Record to schedule the manual TV recording and return to the Recorded TV menu. Changing Your Settings The Media Center Settings option allows you to: ❖ Change settings for your television service provider. ❖...
Getting to Know the Windows ® XP Media Center Edition Listening to Music ❖ Adjust display settings ❖ Audio settings To make a change, click on the desired setting. Changing recording priorities If Media Center encounters a recording conflict between two series, then Media Center uses the series priorities list to decide which show to record.
Getting to Know the Windows ® XP Media Center Edition those files to the Windows Media Player Library for Media Center to be able to find and play them. In My Music, you can: ❖ Play music CDs. You can skip, shuffle, or repeat songs or albums.
Page 162
Getting to Know the Windows ® XP Media Center Edition Listening to Music To add music files: Click Start on the taskbar, and then click Windows Media Player. Click the Media Library tab on the side of the window. The first time you select Media Library, a message tells you that Windows Media Player needs to search your computer for your music files.
Getting to Know the Windows ® XP Media Center Edition Adding Music from Your Hard Drive to Windows Media Player Library You can place all your music files into the My Music folder or into other folders on your hard drive, however, you need to add those files to the Windows Media Player Library for Media Center to be able to find and play them.
Getting to Know the Windows ® XP Media Center Edition Listening to Music Playing Digital Music Files When you first open the Media Center and open the My Music window, you may not find any music files listed unless there is a music CD in your CD drive or unless you have already added audio files to your Windows Media Player Library.
Getting to Know the Windows ® XP Media Center Edition Finding Music Files in My Music After you have added and organized files in Windows Media Player Library, you can browse through your music files in the My Music window. You can search for music files by album title, artist, song title, or music genre.
Getting to Know the Windows ® XP Media Center Edition Listening to Music You can also play a single song from a playlist as follows: In the My Music window, select View Songs. The list displays all the songs in your media library. Use the arrow buttons to select a song, and then press OK or Play on the remote control to play it.
Getting to Know the Windows ® XP Media Center Edition ❖ Play to play the album selected. The Now Playing window opens, and the album starts playing. In the Play window, select a song and press OK on the remote control. You can also select: ❖...
Getting to Know the Windows ® XP Media Center Edition Displaying Your Pictures In the Media Library, select the music file that you want to add to your playlist. Click Add to playlist in the toolbar, and then select your playlist from the drop-down menu.
Page 169
Getting to Know the Windows ® XP Media Center Edition Sample My Pictures screen After you organize your pictures in the My Pictures folder in Windows Explorer, open Media Center to view your pictures: Press the Start button on the remote control to open the Media Center Start menu.
Getting to Know the Windows ® XP Media Center Edition Watching Your Digital Movies Viewing a Slide Show To view pictures as a slide show Press the Start button on the remote control to open the Media Center Start menu. Select My Pictures.
Getting to Know the Windows ® XP Media Center Edition ❖ View your videos in full screen mode or from an inset window in Media Center. Sample My Videos screen Organizing Your Videos When you attach a digital video camera to your PC, Windows asks you how you want to capture your video.
Getting to Know the Windows ® XP Media Center Edition Watching Your Digital Movies If you want to share your videos with others, place them in the Shared Video folder. To do this, click Start on the taskbar, click My Documents, click the Shared Documents folder under Other Places, and then double-click the Shared Video folder.
Getting to Know the Windows ® XP Media Center Edition Playing a Video in Full Screen Mode On the Media Center Start menu, select My Videos. On the My Videos menu, select My Videos or Shared Video. Use the arrow buttons to select the folder you want, and then press OK.
Getting to Know the Windows ® XP Media Center Edition Watching a DVD If a DVD menu appears, use the remote control or the mouse to select the DVD menu items and control the DVD movie playback. Press Stop on the remote control to stop playing the DVD.
Getting to Know the Windows ® XP Media Center Edition ❖ Select DVD Languages to change the language for the DVD soundtrack, subtitles, and menu. ❖ Select Eject to open the disc tray. Playing a DVD movie already in your drive If you already have a DVD movie in your drive, but you have been doing other things in Media Center or in other programs from your desktop, you can play the DVD by:...
Page 176
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Administrator Controlled Settings Some settings apply to all Media Center windows for all users and must be set up by the administrator. These settings are: ❖...
Page 177
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings In the General window, do one of the following: ❖ Select Appearance to turn transition animations or notifications on or off. Use the arrow buttons to select the item to change, and then press OK on the remote control.
Page 178
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Changing TV Recorder Settings The TV Recorder settings allow you to control your recording priorities and options in Media Center. In the Media Center Start menu, select Settings. Select TV.
Page 179
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings To increase disk space, you can: ❖ Delete recorded shows from the Recorded TV window. For more information, refer to the My TV chapter. ❖ Increase the percentage of hard disk space available for recorded TV shows in Default Settings.
Page 180
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings ❖ Select Customize to show or hide channels that appear in the Guide. To show a channel, select the channel check box. To hide a channel, clear the check box. ❖...
Page 181
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Use the arrow buttons to select Block unrated movies, and then press OK. Use the arrow buttons to select the + or - area. Press the OK button on the remote control to scroll through the movie rating levels.
Page 182
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings To select closed captioning: In the Media Center Start menu, select My TV. Select Settings. Select Audio. Use the arrow buttons to select the + or - buttons. Press OK on the remote control to scroll through the choices available.
Getting to Know the Windows ® XP Media Center Edition Changing the Media Center Settings Changing Picture Settings Each user can set his or her own picture settings. In the Media Center Start menu, select Settings. You may need to select the scroll arrows on the Start menu to view Settings.
Chapter 6 Exploring Your Options In this chapter, you will explore other features of your notebook computer. ® Windows XP special features The Windows features and enhancements, including: ❖ New system file protection ❖ A system restore function, allowing you to rollback the system to its previous mode ❖...
Personalizing your desktop Your desktop is your virtual workspace. This section explains how to customize its features for the way you like to work. You can customize the following aspects of the desktop: ❖ Taskbar—which resources to display for quick access ❖...
Exploring Your Options Personalizing your desktop Bringing the world to your desktop With the Windows your desktop with complete World Wide Web integration at a single click. Turning on the Web content interface The first step to bring active content to your desktop is to turn on the Web content interface: Point to an empty space on the desktop and click the secondary button.
To browse the Gallery for more components to add, click Visit Gallery. In order to browse, an active Internet connection must be established. To select some other Web site, type the address of the Web site you want or click Browse to locate it. You can configure the Web content interface in several other ways.
Page 188
Exploring Your Options Personalizing your desktop Choosing a style To select desktop and browsing style options: Click Start, then click My Computer. The My Computer window appears. Select the Tools menu, then click Folder Options. The Folder Options dialog box appears. Sample Folder Options dialog box Click the preferred options.
Personalizing individual windows Just as you can display a Web page on your desktop, you can also display a Web page in an individual window. If you subscribe to the Web page, it can be automatically updated on a regular basis. For example, using this Web integration feature you can monitor weather, game scores, stock prices, or headlines—all in the window of your choice.
Exploring Your Options Personalizing your desktop The elements you can add to the top of the window are: Toolbar element Address Bar Standard buttons Displays buttons for commonly used Displaying a toolbar in a window Click Start, then click My Computer. The My Computer window appears.
Open the folder you want to view as a Web page. In the Tools menu, select Folder Options. In the Tasks section, click the button for Show common tasks in folders. Click Apply, then OK. Sample Control Panel window as a Web page The addition of the name of the folder and instructions for how to use the folder on the left give the window the appearance of a Web page.
Exploring Your Options Using your computer at the office Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A modem (one comes with your computer) ❖...
Exchanging data with another computer To transfer a large amount of information between computers, you need a physical connection and a synchronization program such as Windows Getting started Connect your computer to another computer. Load the synchronization program on both computers. Set any specific options.
Exploring Your Options An overview of using the Internet Connect to the Internet by using a telephone and modem or through other higher-speed communication methods, such as Digital Subscriber Lines (DSL), cable or a satellite link. After your Internet connection has been made, start your Web browser.
The World Wide Web The World Wide Web (or ‘Web’) is a subset of the Internet — a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP). The World Wide Web offers information as text, images, audio, or video to be referenced from anywhere in the world.
Exploring Your Options An overview of using the Internet Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address.
clearinghouse where all the messages are placed, like a gigantic bulletin board. ❖ Online shopping Many Web sites offer products and services for sale. Uploading and downloading files on the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer).
Exploring Your Options Changing the display properties setting Changing the display properties setting Right-click anywhere on your desktop and select Properties. The Display Properties dialog box appears. Sample Display Properties dialog box Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply.
Display settings hot key Using the view DVD movies or presentations on an external device. For more information, see Exploring audio features You can use your computer to record sounds using an external microphone. You can play .wav sound files or audio CDs using the built-in speakers, headphones or external speakers.
Exploring Your Options Exploring audio features Positioning Sample Sound Recorder screen Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. NOTE When you have finished recording, click the Stop button. To hear what you just recorded, click the Play button.
Connecting a monitor, keyboard and mouse Click OK. Your new settings take effect the next time you record. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers.
Exploring Your Options Using the Modular Bay Using the Modular Bay The Modular Bay gives you additional flexibility. By inserting and removing optical drive modules, you can configure your computer for the task at hand without having to carry unnecessary components with you when you travel. HINT: Items from this list that did not come with your computer can be purchased separately.
Unlatching the Modular Bay Slide the module out of the computer. Sliding the module out Inserting a module into the Modular Bay To install a module into the Modular Bay, simply slide the module all the way into the Modular Bay. Using PC Cards PC Cards expand your computer’s capabilities and usefulness.
Exploring Your Options Using PC Cards ❖ Two Type I and Type II cards. ❖ One Type III card. Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later. Other cards may work with your computer, but are likely to be much more difficult to set up and use.
Align the card connectors with an available PC Card slot and carefully slide the card into the slot until it locks into place. Inserting a PC Card If you have a Type III card, insert the connector into the lower NOTE slot.
Exploring Your Options Using PC Cards Removing a PC Card Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use.
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter. Your program stops responding.
Page 208
If Something Goes Wrong If a program has stopped responding, the words “not responding” appear beside its name in the list. Windows Task Manager Applications tab Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working.
The computer shuts down. Your program performs an illegal operation. If you receive the message, “ ,” you should record the details of the message and operation consult the software manufacturer. To record the details: Click the Details button and select the text the operating system displays.
If Something Goes Wrong The Windows The computer starts but, when you press a key, nothing happens. You are probably in Stand By mode and have a software or resource conflict. When this happens, turning the power on returns you to the problem instead of restarting the system. To clear the condition, press the power button until it turns off the computer.
The Windows ❖ The operating system responds differently from the normal routine. ❖ The screen does not look right. Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device.
If Something Goes Wrong The Windows ❖ Reboot For detailed information, refer to your operating system’s documentation. Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet. They include: modem speed, time of day (when everyone else is surfing, your access can be slow) and popularity of the site.
❖ In the search field, type in the topic of the problem with which you need help and follow the on-screen instructions. ❖ Click a problem you would like help with from the listings and follow the on-screen instructions. Resolving a hardware conflict If you receive an error message telling you there is a device driver conflict or a general hardware problem, try using ®...
If Something Goes Wrong Resolving a hardware conflict Resolving hardware conflicts on your own Computer components need resources to accomplish a task. A device, such as a disk drive or a modem, needs a channel to the computer’s Central Processing Unit (CPU). It also needs a direct channel to the computer’s memory to store information as it works.
Resolving conflicts There are three things you can do to resolve hardware conflicts: ❖ Disable the device. For an older device, remove it from the computer. For a Plug and Play device. ❖ Disable another system component and use its resources for the new device.
Page 216
If Something Goes Wrong Resolving a hardware conflict To enable a device, look at the far right of the toolbar. Look for an icon of a monitor with a strike mark through a circle on the front. When you mouse over the small icon, the status of Disabled displays.
❖ The General tab, which provides basic information about the device. ❖ The Resource tab, which lists resources assigned to the monitor, DVD-ROM, and other power-using functions. ❖ The Drivers tab, which displays the drivers being used by the device. A Troubleshooting button is also present.
If Something Goes Wrong Resolving a hardware conflict the memory module installed, the error is not caused by the memory module. Toshiba recommends using only memory approved by NOTE Toshiba. Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and optional secondary battery).
Let the battery discharge completely, then try charging it again. Check the power options using the Toshiba Power Management Utility. Have you added a device, such as a PC Card or memory module, that takes its power from the...
If Something Goes Wrong Resolving a hardware conflict that the program does not assign different meanings to any of the keys. You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer.
Page 221
❖ Press priority is not set for the built-in screen. The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties. This opens the Display Properties dialog box.
If Something Goes Wrong Resolving a hardware conflict The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode.
Click on Properties. Click the Tools tab. Click the Check now button. The Check Disk box appears (for example, Check Disk You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors ❖...
Page 224
If Something Goes Wrong Resolving a hardware conflict Open the drive tray and remove the disc. Make sure the drive tray is clean. Any dirt or foreign object can interfere with the laser beam. Examine the disc to see whether it is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
Sound system problems You do not hear any sound from the computer. Adjust the volume control. If you are using external headphones or speakers, check that they are securely connected to your computer. The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers.
Page 226
If Something Goes Wrong Resolving a hardware conflict Other cards must be set up before you can use them. Use the ® Windows XP PC Card (PCMCIA) Wizard to set up the card. Refer to your Microsoft information, or refer to the documentation that came with the PC Card.
Page 227
Click My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. Click the Hardware tab. Click the Device Manager button. Double-click the category listed as PCMCIA adapter. The operating system displays your PC Card’s Properties dialog box, which contains information about your PC Card configuration and status.
Page 228
If Something Goes Wrong Resolving a hardware conflict Remove the card from the slot. Never swap modules when the computer is in Hibernation or Stand By mode. This is known as “warm swapping” and is not supported with this computer. For more information on Hibernation and Stand By modes, see on page 85 The system does not recognize your PC Card or...
Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray.
If Something Goes Wrong Develop good computing habits Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack.
Page 231
❖ Copy files to a CD or other media, following the steps in “Saving your work” on page ❖ Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape. Some people use a combination of these methods, backing up all files to tape weekly and copying critical files to media, such as a CD, on a daily basis.
GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. ®...
Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. You can access Toshiba on the Internet using any Internet browser by typing Toshiba voice contact Before calling Toshiba, make sure you have: ❖...
If Something Goes Wrong Other Toshiba Internet Web sites Other Toshiba Internet Web sites toshiba.com computers.toshiba.com www.toshiba.ca www.toshiba-Europe.com www.toshiba.co.jp/ index.htm http://servicio.toshiba.com Toshiba’s worldwide offices Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road North Ryde NSW 2113 Sydney Australia Belgium Toshiba Information Systems Benelux (Belgium) B.V.
Page 235
Italy If Something Goes Wrong Toshiba’s worldwide offices Denmark Scribona Danmark A/S Naverland 27 DK2600 Glostrup Denmark France Toshiba Systèmes (France) S.A. 7, Rue Ampère 92804 Puteaux Cédex France Greece Ideal Electronics S.A. 109 Syngrou Avenue 176 71 Kalithea Athens...
Page 236
800-457-7777 (within the US) 949-859-4276 (outside the US - this call may incur long distance charges) Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. Tel: 5249-6500 The Netherlands Toshiba Information Systems Benelux B.V.
Page 237
Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States If Something Goes Wrong Toshiba’s worldwide offices Singapore Toshiba Singapore Pte. Ltd. 438B Alexandra Rd. # 06-01 Alexandra Technopark Singapore 119968 Slovenia Inea d.o.o. Ljubljanska 80 61230 Domzale...
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Instant password security Without a password key combination turns off the display and...
the display’s content reappear. The Windows system log-on screen will appear, prompting you for a password. After typing in the password for the current user, press Enter To activate the password feature: Click Start, and then click Control Panel. Click Appearances and Themes. Click one of the following: ❖...
Sample power usage modes The power usage mode in the Windows under AC power is Full Power only. The properties of each mode are set in the Toshiba Power Management utility. This hot key cycles through the different alarm ®...
Stand By mode This hot key puts the computer into Stand By mode. Sample Stand By confirmation box Stand By mode ❖ A message box is displayed by default to confirm that the computer is going into Stand By mode. This message box can be set so it does not display.
Hibernation mode Hibernation mode This hot key puts the computer into Hibernation mode. Sample Hibernation confirmation box ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display.
Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window In o resolution of the internal display panel to match the resolution of the external display device. Display modes display mode options. The display mode options are: Built-in display panel only, Built-in display panel and external monitor simultaneously, External monitor only.
Enabling a wireless device Enabling a wireless device This hot key enables/disables the optional wireless devices in your computer (for systems with Wi-Fi The wireless modes are: Wi-Fi enabled—This enables the Wi-Fi module. Wi-Fi disabled—This disables the Wi-Fi module. Disabling or enabling the TouchPad This hot key enables/disables the TouchPad.
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved...
Appendix C Using ConfigFree ™ with your Toshiba Computer ConfigFree™ is a set of utilities used for configuring networks that use both wired and wireless network devices. These utilities include the following: ❖ Connectivity Doctor—The Connectivity Doctor utility is used to help fix networking problems with your notebook computer.
Quick Connect—The Quick Connect utility is used to configure a wireless LAN connection (ad hoc connection) between a personal computer and a Toshiba Wireless Projector. The Toshiba Wireless Projector utility must be installed in order to enable Quick Connect. For...
Help—Displays the online help file. Starting ConfigFree To start ConfigFree, do any of the following: ❖ (Microsoft and then point to All Programs. Point to the TOSHIBA folder, the Networking, and then click ConfigFree. ❖ Double-click the ConfigFree icon ❖...
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Connectivity Doctor The Connectivity Doctor displays the connection configuration and the status of all wired and wireless LAN devices that are connected to the network. For wireless network devices, the signal strength and WEP (Wired Equivalent Privacy) key settings (if applicable) also display.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Connectivity Doctor screen The Connectivity Doctor screen automatically refreshes. However, you can also use the Refresh button to refresh the screen. Device Settings The Device Settings screen displays a list of all wired, wireless, and infrared (for systems with infrared) devices that are connected to the network.
Page 251
Using ConfigFree™ with your Toshiba Computer Viewing the sample Device Settings screen ❖ Network Connections—Displays the Network Connection window, which contains detailed information about the network connection. ❖ Enable/Disable—You can easily enable or disable any of the listed devices simply by selecting the desired device, and then clicking the Enable/Disable button.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Profile Settings The Profile Settings utility displays a list of all the registered profiles in ConfigFree. You can also add, modify, and delete profiles; switch the profile being used; and view specific details about each profile.
Toshiba Wireless Projector. As a result, you will not be able to use the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection will be broken and later re- established.
❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this will disconnect the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device.
Using ConfigFree™ with your Toshiba Computer ❖ From the Profile Settings screen, you can click the Auto Switch button. Auto Switch (Cable Disconnect) If a wired network cable is disconnected from the network, the Auto Switch (Cable Disconnect) option will automatically switch to another network device.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory complementary metal-oxide semiconductor...
Page 257
Glossary DIMM DVD-ROM digital versatile (or video) disc read-only memory EPROM HTML IEEE PCMCIA SCSI dual inline memory module disk operating system dots per inch digital versatile (or video) disc enhanced capabilities port erasable programmable read-only memory file allocation table Federal Communications Commission fast infrared gigabyte...
Page 258
SDRAM SRAM SVGA Terms The following terms may appear in this user’s guide. active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 259
Glossary basic input/output system (BIOS) — See BIOS. baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second).
Page 260
CD — An individual compact disc. See also CD-ROM. CD-ROM (compact disc read-only memory) — A form of high- capacity storage that uses laser optics instead of magnetic means for reading data. See also CD. Compare DVD-ROM. central processing unit (CPU) — The chip that functions as the “brain” of the computer.
Page 261
Glossary CPU cache — A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs. See also cache, L1 cache, L2 cache. cursor —...
Page 262
diskette — A thin, flexible disk in a protective jacket that stores magnetically encoded data. Diskettes can be removed from the computer and come in two sizes: 5.25-inch and 3.5-inch. Your computer uses 3.5-inch diskettes. See also double-density diskette, high-density diskette. document —...
Page 263
Glossary file — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document. file allocation table (FAT) — The section of a disk that keeps track of the location of files stored on the disk.
Page 264
— The physical components of a computer system. Compare software. Hibernate — A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 265
Glossary LAN (local area network) — A group of computers or other devices dispersed over a relatively limited area and connected by a communications link that enables any device to interact with any other on the network. liquid crystal display (LCD) — A type of display that uses a liquid substance between two transparent electrode panels.
Page 266
multimedia — A combination of two or more media, such as sound, animation, and video in a computer program or presentation. Musical Instrument Digital Interface — See MIDI. network — A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail.
Page 267
Glossary Plug and Play — Generally, refers to the computer’s ability to automatically configure itself to work with peripheral devices. When capitalized, refers to a standard that, when followed by a device manufacturer, allows a PC to configure itself automatically to work with the device.
Page 268
RJ-11 — A modular connector used on most U.S. telephone systems and direct-connect modems. The RJ-11 connector is a 6-wire connector. RJ-45 — A connector used to attach computers to LANS (local area networks) and to link ISDN (Integrated Services Digital Network) devices to NT-1 (Network Terminator devices).
Page 269
Glossary TFT display — See active-matrix display. universal serial bus (USB) — A serial bus that supports a data transfer rate of up to 12 Mbps (12 million bits per second). USB can connect up to 127 peripheral devices through a single all-purpose USB port. USB allows hot swapping of peripherals.
Index AC power light 50 Accessories programs 117 audio features 199 avoiding injury 38 battery caring for 103 changing 101 charge not lasting 219 charging 61 conserving power 99 disposal 105 installing 101 light 50 monitoring power 97 not charging 218 power usage mode 240 removing 101 RTC (real-time clock) 96...
Page 271
computer 62 click 51 closing programs 122 comfort chair 39 lighting 40 work habits 41 commands Hibernate 85 powering down 84 Stand By 86 communications programs 83 setting up 83 system resources 214 via modem 83 compact discs inserting 77 problem solving 224 removing 81 computer...
Page 272
Index corrupted/damaged data files 223 missing files/trouble accessing a disk 222 running slow 223 diskettes copying files to 72 display doesn’t look normal/flickers 221 external monitor not working 222 latch 49 properties 126 screen is blank 220 display modes changing 243 display panel opening 49 Display settings...
Page 273
hot key display modes 243 display settings 199 power usage mode 240 Stand By mode 241 wireless mode 244 hot keys display modes 243 instant password 238 keyboard functions 244 sound 240 hot swapping 204 precautions 206 Hypertext Transfer Protocol (HTTP) i.LINK FCC 3 icon 109...
Page 274
221 checking device properties 216 compact discs not running computer hangs when PC Card computer will not power up 209 contacting Toshiba 232 corrupted/damaged data files 223 Device Manager 215 disabling a device 215 disk drive is slow 223...
Page 275
drive drive tray doesn’t eject 224 external display not working 222 external keyboard not working external monitor 220 faulty memory 217 hardware conflict 213 hardware conflict caused by legacy device 214 Help 212 high-pitched noise 225 illegal operation 209 Internet bookmarked site not found 212 Internet connection is slow 212 keyboard...
Page 276
System Restore 130 System Tools 130 system tray 110 taskbar 110 telephone line text file 115 toolbars Toshiba Toshiba Accessories TouchPad transferring information between traveling tips 105 Turn Off turning computer on/off 50 turning off the computer 84 tutorials 114...
Page 277
240 warranty SelectServ 36 Web address 196 Web browsers 195 Web content interface 186 Web sites 233 Web sites,Toshiba 234 windows hiding 118 repositioning 118 resizing 118 Windows Explorer 117 Windows Help 109 Windows Media Player 79...
Need help?
Do you have a question about the P25-S670 and is the answer not in the manual?
Questions and answers