Icom AP-95M Connection Manual

6. Connecting with wireless LAN
NOTE: For the first time to access or after an initialization, you must configure the Time Zone and Country. See the "Setting the Time Zone
and Country" leaflet for details.
The following procedures describe how to connect to the AP-95M through a wireless LAN, based on Microsoft
L The procedure differs, depending on the connected devices, so follow their instructions when using the other devices.
q Start the AP-95M, and then turn ON the PC.
w Click the Wireless Network Connection icon.
Click
7. About installation
This product radiates or receives radio wave from its top surface, so we recommend mounting on a wall or ceiling.
You can mount on the wall or ceiling using the supplied bracket, by following procedure q to t below.
L To use the security wire, refer to the instruction manual on our website.
R DANGER!
Mount the unit securely to a thick surface that can support more than 600 g (1.3 lb).
Ceiling or wall
Mark the screw positions using the
bracket as the template.
80 mm (3.1 in)
Use the supplied anchor if mounting on drywall.
q
13 × 43 mm (0.5 × 1.7 in)
To remove the unit from the braket:
While holding down this notch to release
the lock, twist the unit counter-clockwise
until it is detached from the bracket.
Mount the unit to the bracket by hooking the
screws (e) to the hook slots (r) and twisting
Screw hole the unit until it makes a click sound (t).
Tapping screw (Supplied)
3.5 × 32 mm (0.1 × 1.3 in)
w Hook slots
t
r
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the
United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
Adobe, Acrobat and Reader are registered trademarks of Adobe Systems Incorporated in the United States and/or other countries.
All other products or brands are registered trademarks or trademarks of their respective holders.
Windows
®
e Select the SSID set to the AP-95M and click [Connect].
Then follow the instructions.
q Select
w Click
• The SSID is set to "WIRELESSLAN-0" by default.
52 mm (2 in)
Dimensions
42 mm (1.7 in)
Wall or
ceiling
Hooking screws
e
(Supplied)
2.6 × 12 mm
(0.1 × 0.5 in)
– 4 –
WIRELESS ACCESS POINT
AP-95M
10.
®
IEEE802.11ac Wave 2 standard
1. System Requirements
D Supplied Accessories
• Mounting bracket set
• Precautions Guide
• Connection Guide (This guide)
• Power adapter
( The adapter may not be supplied or differs, depending on the
access point version.)
About this Connection Guide:
This Connection Guide explains the basic operation of the
AP-95M. Access our website to download the instruction
manual.
Icom website http://www.icom.co.jp/world/support/
2. Panel description
D About the indicators
Indicator 5 GHz
Lights 1 or mode connection/WPS succeeded
Green
Blinks —
Lights —
Orange
Blinks —
* 1 When there is no wireless device to communicate with the AP-95M, or no wireless communication is performed while the Wireless Unit is
enabled, the indicator turns OFF. The time when the indicator turns OFF differs, depending on the communication status.
* 2 While booting up, the [POWER] indicator lights green → blinks green → lights green.
L All indicators light while booting.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
Dec. 2018
Read the "PRECAUTIONS" leaflet first, if you have not done so.
CONNECTION GUIDE
Thank you for purchasing this Icom product. The AP-
95M wireless access point is designed and built
with Icom's IP network technology. It complies with the
"IEEE802.11ac Wave 2" standard, and is designed for
dual band communications in the 5 GHz and 2.4 GHz
bands.
D Other requirements
• PC
• LAN cable
NOTE:
• Adobe ® Acrobat ® Reader
display the downloaded PDF instruction manual.
• If your PC does not have Adobe
download it from the Adobe
[MODE]
Refer to "RESETTING THE AP-95M" in the
Precautions Guide, for details.
2.4 GHz LAN
LAN connected
*1 Operating [MODE]
(1000BASE-T)
LAN is communicating
— WPS is running
(1000BASE-T)
LAN connected A firmware update is
—
(10BASE-T/100BASE-TX) ready (Online update)
LAN is communicating
—
(10BASE-T/100BASE-TX) (Blinks for 30 seconds)
– 1 –
® is required on your PC in order to
® Acrobat ® Reader ® , please
® website.
*2
MODE
POWER
ON
Booting
—
WPS failed
—
A7493W-2EX Printed in Japan
© 2018 Icom Inc.