Sharp XE-A102 Quick Start Manual page 2

XE-A102 Quick Start Guide
2 Reset the Cash 3 Install Batteries
Register
To ensure that your cash Prepare three new R6 or LR6 batteries
register operates properly, ("AA" size), and install them according to
initialize it using the the procedure shown below with the AC
following procedure. cord connected and set the mode switch
to REG position. These batteries are
1. Insert the mode key into necessary for memory backup.
the mode switch and turn
1 Pull the printer cover forward and
the key to the REG
detach it.
position.
2. Insert the plug into the AC
2. Open the battery cover next to the
outlet. A buzzer will
paper roll cradle.
sound three times.
IMPORTANT
This operation must be
performed without
batteries loaded.
3. The register display
should now show "
0.00".
3. Install three new R6 or LR6 batteries
("AA" size). Make sure that the
batteries are installed as per the
diagram below.
x to confirm the
4. Press
clock starts from " 0-
00".
5. Press c to cancel the
time display.
4. Confirm the no battery symbol
" " lights off.
5. Close the battery cover.
4 Install the Paper Roll
1. Set the paper roll in the paper roll cradle as
shown in the diagram.
2. Insert the paper straight into the paper inlet,
and press o. The paper then feeds through
and appears in the print area.
3. (For journal printing only) Insert the top end of
the paper into the slit in the spool shaft and
wind the paper two or three turns.
4. (For journal printing only) Place the take-up
spool on the bearing.
5. Replace the printer cover.
5 Basic Programming
Set the mode key to the Z/PGM position.
Set Time and Date
1. Enter the time in 4 digits ("hhmm" format) using
the 24 hour system.
In case of 2:30 p.m.; 1430
2. Press S once.
3. Enter the date in 6 digits using the day-month-year format.
In case of 26 August, 2005: 260805
4. Press S twice. A programming report will be printed.
VAT(Tax) rate programming
Your cash register comes with the ability to program six kinds of tax system, and is
preprogrammed so that VAT1 through VAT4 are calculated manually. If you have to
change the tax system, please refer to the part of "Quick Start Operations" in the
insruction manual.
➜ ➜ ➜ ➜ ➜
9 S x x
A B
When lower tax limit is not specified
Parameters
A: VAT (Tax) 1: 1 VAT (Tax) 2: 2 VAT (Tax) 3: 3
B: Tax rate (00.0000% to 99.9999%)x10000 (Default: 00.0000%)
C: Lower tax limit (0 to 9999) only for TAX system. (Default: 0)
Department tax status
As the default settings, VAT(tax) 1 is applied for all departments. If you must change
the status, use the following procedure.
00 7 ➜ x ➜ ( s ➜ ) Department key (➜
CDEF
(Press s to program departments 5 to 8.)
Parameters
C thru F: 0 for not applying tax or 1 for applying tax
C for VAT4 or TAX4 D for VAT3 or TAX3
E for VAT2 or TAX 2 F for VAT1 or TAX1
For example, when you apply VAT2 for department 5, enter:
0000 1 07s!
Tax 2(E)
With regard to other parameters (the place of 00 and 7), please refer to the
part of "Quick Start Operations" in the insruction manual.
For additional basic information of programming and operation, please
refer to the part of "Quick Start Operations" in the instruction manual.
English
➜ ➜ ➜
S ( S
C
: To
)
finish programming
VAT (Tax) 4: 4
S
: To
)
finish programming