Page 1
FIFTH WHEELS 2021 Owner’s Manual A subsidiary of Thor Industries, Inc. 0311723.2021...
Page 3
Weighing Your Tow Vehicle and RV Section 4: Vehicle Operation Towing RV Brake System Electric Brakes Brake Controller (customer supplied) Travel Trailer Breakaway Switch Hydraulic Brakes (if so equipped) Disc Brakes (if so equipped) 2021 Starcraft Telluride FW RevA: Revision page 12...
Page 4
Table of Contents Towing Behind Your RV Entrance Door Step(s) Entrance Door Rear Vision Camera Prep/Camera (if so equipped) Campsite Hook-Up LCI 3.0 Leveling System (if so equipped) Auto Leveling Touch Pad OneControl Touch Panel OneControl App (for your phone or tablet) Linc Remote Control Linc Remote Troubleshooting...
Page 5
Table of Contents Section 6: Electrical System The Electrical System In Case Of An Electrical Fire Command Center Command Center Panel Command Center Panel w/Switch Modules GFCI Receptacle Testing The Campsite Power Connection Power Converter Converter w/Charge Wizard (if so equipped) 12-Volt DC System 12-Volt Fuse Panel Replacing a Fuse...
Page 6
Table of Contents Section 8: Plumbing System Plumbing System Plumbing System Maintenance Monitor Panel Monitor Panel Command Center Fresh Water System Water Pressure Regulator (customer supplied) Water Purification System (if so equipped) Water Pump Strainer Filter Housing Draining The Fresh Water System Exterior Fresh Water Drain 6 In 1 Utility Center (if so equipped) Potable Water Label...
Page 7
Table of Contents Attaching the “Quick Coupler” Connection Quick Connect Coupler Range Hood (if so equipped) Refrigerator Water Heater – See Plumbing Section Outside Kitchen (if so equipped) Quick Connect Coupler Exterior Refrigerator LP Gas Grill (if so equipped) Cleaning the Grill Section 11: Electronics Antenna HDTV Antenna (if so equipped)
Page 8
Table of Contents Section 15: Additional Information Featured Components Quick Reference Chart Vehicle Maintenance Record Ownership Notification...
Section 1: Warranty & Service WARNING: Read all instructions in this manual and component manufac- turer supplied information before using your RV. This manual has been provided by your recreational vehicle manufacturer for the sole pur- pose of providing instructions concerning the operation and maintenance of this recreational vehicle.
Page 10
Canada may differ to conform to Canadian Codes. Dealer Responsibility At the time of sale of the new RV, your Starcraft dealer is expected to: Deliver your RV in the best condition possible. Your RV must pass the dealer’s pre-delivery inspection (PDI), including all systems tests.
Page 11
(or any effect of the alterations) to any of the parts, components, systems or assemblies installed by Starcraft. Starcraft is not responsible for the safety or quality of design features, materials or workmanship of any alterations by such suppliers.
Canada. In addition, the club offers a variety of local and regional activities throughout the year. By belonging to the Starcraft Camper Club, you will find new ways to enjoy your RV and make friends all across the country.
Section 1: Warranty & Service Safety Alerts Throughout this manual, certain items are labeled NOTE, CAUTION, WARNING, and DANGER. These terms will alert you to precautions that can involve risk to your vehicle or to your personal safety. Read and follow them carefully. National Safety Associations and organizations require many of the instructions listed.
Section 1: Warranty & Service Reporting Safety Defects In the United States: If you believe that your recreation vehicle has an alleged defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA), in addition to notifying our Cus- tomer Service Department.
Section 1: Warranty & Service Customer Responsibility It is important you read and understand all instructions and precautions before operating the recreation vehicle. Even if you are an experienced RV’er we encourage you to thoroughly read this Owner’s Manual, as well as the information contained in your Warranty Packet and Chassis Guide (motorized only).
Section 1: Warranty & Service Obtaining Service For Separately Warranted Items Your selling dealer is responsible for servicing your recreational vehicle before delivery, and has an interest in your continued satisfaction. We recommend your dealer perform all inspection, warranty and maintenance services. Some dealers may be authorized service centers for those OEMs whose products are warranted separately and excluded from the Limited Warranty.
Page 17
RV is delivered to the first retail purchaser by an independent, authorized dealer of Starcraft, or, if the dealer places the vehicle in service prior to retail sale, on the date the RV is first placed in such service.
Page 18
Pay any freight or transportation costs, import duties, fees and all incidental expenses associ- ated with obtaining warranty service. If you need assistance you may contact Starcraft RV at 903 S. Main Street, P.O. Box 460, Middlebury, Indiana 46540, Attn: Customer Service, (800) 283-8267.
Page 19
10 days of your discovery of the substantial defect; AND (2) you deliver the RV to Starcraft or an authorized dealership at your cost and expense. If this primary repair remedy fails to successfully cure any substantial defect after a reasonable number of repair attempts, your sole and exclusive remedy shall be to have Starcraft pay an independent service shop of your choice to perform repairs to the substantial defect.
Page 20
Certain things completely discharge Starcraft from any obligation under this warranty and void it. By way of example, the following shall discharge Starcraft from any express or im- plied warranty obligation to repair or replace any defect that results from: any rental or other...
Page 21
In addition, this warranty is not intended to extend to future performance, and nothing in this warranty, or any action of Starcraft, or any agent of Starcraft, shall be interpreted as an extension of the warranty period or this limitation period. Some states do not allow a reduc- tion in the statute of limitations, so this reduction may not apply to you.
Page 22
STATE TO STATE OR PROVINCE TO PROVINCE. ALL ACTIONS OF ANY KIND RELATING TO THE RV SHALL BE DECIDED BY A JUDGE RATHER THAN A JURY. STARCRAFT RV 903 S. Main Street * P.O. Box 460 * Middlebury, IN 46540...
Section 2: Occupant Safety Secondary Means of Escape (Exit Window) Your recreation vehicle has been equipped with a window(s) that serves as a secondary means of escape. The window(s) will allow a quick exit from the vehicle during an emer- gency if access to the main entrance door is not available.
Section 2: Occupant Safety Lever style latch Remove the screen by pulling the red tab (upper rightarrow). Pull the lever out from the sash clamps. Swing the lever out so it is positioned straight out from the win- dow. Push the lever (and window) out to open and exit the ve- hicle.
Section 2: Occupant Safety Do not check the pressure, test or practice using the fire extinguisher by squeezing the trigger, even briefly. The fire extinguisher is not rechargeable or refillable. Once used, it will gradually lose pressure and will not be fully charged for use in an emergency.
Section 2: Occupant Safety cleared. The LED light will also give a visual indication of a sounding alarm. When the battery becomes weak, the alarm will “beep” about once a minute indicating a low battery. This warning should last for 30 days. You MUST replace the battery once the alarms low battery warning (beep) starts to assure continued protection.
Page 27
Section 2: Occupant Safety Do not cover or obstruct the carbon monoxide/propane alarm with any- thing that could prevent gas from entering the alarm. This alarm is not designed to detect smoke, fire or gases other than car- bon monoxide and propane. The carbon monoxide detector installed is intended for use in ordinary indoor locations of recreation vehicles.
Page 28
Section 2: Occupant Safety fumes, adhesives, lacquer, kerosene, glues, wine, liquor, most cleaning agents and the pro- pellants of aerosol cans. High temperatures can activate glue and adhesive vapors. If you close up a recreational vehicle on a hot day, the chemicals used in its construction may be detected for months after the vehicle was constructed (for more information, refer to Sec.
Page 29
Section 2: Occupant Safety recreation vehicle. If problems are identified during this inspection, have the alarm serviced immediately. Note any combustion equipment not inspected by the technician and consult the manufacturer’s instructions or contact the manufacturer directly for more information about carbon monox- ide safety and this alarm.
Section 2: Occupant Safety Repair or replace the combination carbon monoxide/propane alarm when the alarm no lon- ger functions. As with any electronic product, it has a limited life. Alarms that do not work cannot protect you. NOTE: The carbon monoxide/propane alarm manufacturer strongly recommends replacement of the detector five years after the date of purchase.
Page 31
Section 2: Occupant Safety Condensation Condensation may cause dampness, mildew, mold, staining and, if allowed to continue, it may result in damage to the recreation vehicle (damage caused by condensation is not warrantable). It can also lead to mold or mildew issues, which could be a health hazard.
Page 32
Section 2: Occupant Safety Notes: Maintenance Record Table of Contents...
Section 3: Pre-Travel Information Tow Vehicle If you plan to tow your recreation vehicle with a tow vehicle you already own, or if you plan to purchase a new one, make sure the Gross Vehicle Weight Rating (GVWR) or your recreation vehicle does not exceed your tow vehicles towing rating.
Page 34
Section 3: Pre-Travel Information OCCC Label (Occupant and Cargo Carrying Capacity The upper portion of this yellow label is federally required and includes the maximum Occupant & Cargo Carrying Capacity that may be placed in or on the trailer as it was manufactured and weighed before leaving the factory.
Section 3: Pre-Travel Information Loading Your Recreation Vehicle Never load the RV in excess of the GAWR for either axle. Overload- ing your RV may result in adverse handling characteristics and dam- age to the RV. DO NOT EXCEED YOUR GVWR! This means you should weigh your RV as loaded for your normal travel to determine the actual weight.
Section 3: Pre-Travel Information Rear Bumper Do not add items to the recreation vehicle rear bumper. Add-on items will eventually damage your bumper. Damage caused by such aftermarket equip- ment installation or improper loading voids the Towable Limited Warranty. The rear bumper of your RV is not designed to carry cargo. Items that extend beyond the bumper OR weigh over 100 lbs.
Page 37
Section 3: Pre-Travel Information Your recreation vehicle manufacturer cannot be responsible for the suspension system of any tow vehicle. There are a variety of tow vehicle suspension systems available that will affect the pin box height, stability and levelness of a hooked up RV. Make sure your dealer is aware of the tow vehicle you are using so a compatible hookup is achieved.
Section 3: Pre-Travel Information Wire Harness/Connector Plug A 7-way wire harness/connector plug is wired into your trailer to connect electrical power from the tow vehicle for travel. This supplies power to the RV brakes, taillights, clearance lights, turn signals, brake lights, etc. Wiring to operate your brakes must be the same size in both the tow vehicle and RV (the RV brake wiring is 12-gauge wire).
Page 39
Section 3: Pre-Travel Information To weigh your tow vehicle and RV Total weight of your tow vehicle and RV must not exceed the GCWR. Do not assume that you can tow a RV that happens to be within the ca- pacity of the tow vehicle hitch.
Page 40
Section 3: Pre-Travel Information Notes: Maintenance Record Table of Contents...
Section 4: Vehicle Operation Towing If your RV is equipped with the Command Control Bluetooth system, make sure you turn off your battery disconnect switch according to the following instructions. BEFORE TOWING YOUR RV ON THE ROADWAY: TURN OFF THE BATTERY DISCONNECT SWITCH! Certain components inside the RV can unexpectedly activate which could result in personal injury or property damage.
Page 42
Section 4: Vehicle Operation When descending a long hill, drop down into a lower gear or range. Avoid conditions that require excessive and prolonged use of your brakes. Apply and release brakes at short inter- vals to allow them to cool. The tow vehicle transmission and engine will help in controlling downhill speed and can lengthen brake life.
Page 43
Section 4: Vehicle Operation system working properly. Brake Controller (customer supplied) The brake controller should be installed in the tow vehicle to work in conjunction with the RV electric brakes. Consult with your dealer or the brake controller OEM to decide what is right for your towing combination.
Section 4: Vehicle Operation Towing Behind Your RV DO NOT tow anything behind your RV. The RV frame and bumper are not designed for towing. Towing items behind your travel trailer or fifth wheel, or overloading the rear, will void the warranty and may result in: damage to the RV or add-on items, towing difficulties, property damage and/or personal injury.
Section 4: Vehicle Operation NOTE: Locks on entrance and baggage doors need biannual lu- brication using a light coat of silicone spray. Conditions such as rain, salt, dust and pollution may increase the maintenance needs. Rear Vision Camera Prep/Camera (if so equipped) Rear Vision Camera Prep Your recreation vehicle may be pre-wired to allow for installation of a (customer supplied and customer installed) rear vision camera.
Page 46
Section 4: Vehicle Operation LCI 3.0 Leveling System (if so equipped) The LCI Ground Control 3.0 is an electric 4 or 6 point automatic leveling control. The system utilizes one main control board and a separate waterproof remote level sensor to measure and manage level point, and can be operated from several user interface devices including: Auto Leveling Control Touch Pad - Mounted outside the RV within view of the hitch.
Page 47
Section 4: Vehicle Operation NOTE: Pressing both the arrow buttons simultaneously turns on the touchpad. Touchpad will time out after 7 minutes of non-use. Auto Level Touchpad LED Indicator status: OFF - Touch pad is locked Solid Green - Touch pad is active Blinking Green - Jacks are moving Solid Red - Low battery Blinking Red - Error...
Page 48
Section 4: Vehicle Operation Select AUTO LEVEL and the auto leveling process begins. Front of the RV will seek a position near level. Rear jacks will be grounded (on 4 point system). Side to side leveling will begin. Each jack will perform a final grounding touch. NOTE: On a 6 point system the 2 middle jacks will be grounded to stabilize the trailer.
Page 49
Section 4: Vehicle Operation NOTE: The PIN is not needed or asked for if the tablet is attached to the docking station and connected to the USB cable inside the RV. The App will now display all functions. Choose Leveler. The following functions can be operated using the OneControl App.
Section 4: Vehicle Operation Troubleshooting Refer to the Lippert Ground Control 3.0 manual for troubleshooting information which in- cludes the following: OneControl Touch Panel Error Codes Special Jack Error Codes on the OneControl Touch Panel How to manually override the jack motor Setting Zero Point Calibration Zero point is the programmed point that the RVwill return to each time the Auto Level feature is used.
Section 4: Vehicle Operation NOTE: The gears can be stripped out if the stab jack is manually retracted/extended to its fullest extent and the operator continues to rotate the manual override. Emergency Stopping Always carry road flares or reflective warning signs. Pull off the roadway as far as possible for emergency stopping.
Section 4: Vehicle Operation Wheel Lugs After your first trip, check the wheel lug torque periodically for safety. Check the wheel lugs after winter storage, after a wheel removal, before starting a trip or following extensive braking: Use the correct star pattern sequence to attach the recreation vehicle wheels. Start all nuts by hand to prevent cross threading.
Page 53
Section 4: Vehicle Operation Wheel Lug Nut Torque Values Prior to travel and after excessive braking, wheel lug nuts should be checked for torque. Torque readings must fall within the Final Torque Values in chart above. Torque specifications should be checked using a proper torque wrench. If the torque falls below the Final Torque Values, additional torque is required.
Page 54
Section 4: Vehicle Operation Lug Nut Pattern and Warning Label The following labels showing the proper lug nut tightening pattern and a warning label are located on the driver side of the A frame hitch on travel trailers, and on the driver side of the pinbox on fifth wheel units.
Page 55
Section 4: Vehicle Operation Tire wear should be checked frequently. Once a wear pattern becomes firmly established in a tire it is difficult to stop, even if the underlying cause is cor- rected. Tire pressure Failure to follow proper inflation guidelines may result in tire failure, which, under certain circumstances can cause loss of vehicle control or accidents that may result in property damage, bodily injury and/or death.
Section 4: Vehicle Operation When you are using your Recreational Vehicle, check inflation pressure weekly. Pressure should be checked when the tires are cold. During travel, tires heat up and pressure in- creases. Do not bleed air from hot tires or your tires may then be under-inflated. NOTE: Cold tire inflation pressure is defined as a tire that has not been used for three or more hours, or has been driven less than one mile.
Section 4: Vehicle Operation If you experience a flat tire on your recreational vehicle while driving, gradually decrease your speed and move the recreational vehicle to a safe place on the side of the road. Keep the recreational vehicle attached to the tow vehicle. Block the tire on the opposite side of the recreational vehicle from the tire you are changing.
Page 58
Section 4: Vehicle Operation NOTE:If the manual crank access port is located in a slideout, the slideout room must be in the travel position to allow the crank to reach the mechanism used to raise or lower the tire. Raising and lowering the hoist Crank Access Port The crank handle to raise and lower the tire will be located (fas- tened to the sidewall) in a basement compartment of the recreation-...
Section 4: Vehicle Operation To install the tire on the tire carrier Place the tire on the carrier with the top lug bolt insert- ed into one of the holes in the tire rim and the bottom lug bolt in the center of the rim. Install the top lug nut.
Section 4: Vehicle Operation Awnings (if so equipped) Awnings must be closed (and locked if applicable) while the RV is in transit. The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. Retract the aw- ning if: If wind or extended periods of rain are expected If you leave the RV unattended for a length of time, to avoid unexpected...
Section 4: Vehicle Operation Power Awnings (if so equipped) Awnings must be closed (and locked if applicable) while the RV is in transit. The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the recreation vehicle. If wind or extended periods of rain are expected, retract the awning.
Page 62
Section 4: Vehicle Operation Hold on to the awning arm to keep it steady while adjusting the pitch. Press in the pitch adjustment pins located on the scissor arm. Applying LIGHT pres- sure on the arm will decrease the force required to press the pitch adjustment pins. Slide the scissor arm to the desired set hole –...
Page 63
Section 4: Vehicle Operation Press the power switch to ON. The Direct Response system is activated and man- ual controls are active. All functions are disabled if the switch is off. Press and hold the EXTEND switch to open the awning. Press and release the RETRACT switch.
Page 64
Section 4: Vehicle Operation Lippert Solara® Power Awnings (if so equipped) Awnings must be closed (and locked if applicable) while the RV is in transit. The effects of wind and rain on an awning are unpredictable and can cause severe damage to the awning and/or the RV. If wind or extended periods of rain are expected, retract the awning.
Page 65
Section 4: Vehicle Operation Adjusting the Pitch Extend the awning to the desired location. NOTE: If the pitch is not manually set, the awning will pitch itself to purge excessive water pooling in one location and may dump a significant amount of water to either end of the awning without notice. Pitch can be set manually by adjusting the articulating arm to tip one side of the awning to allow water runoff.
Page 66
Section 4: Vehicle Operation NOTE: Caution should be used when retracting the awning manu- ally. The use of a stepstool or ladder may be required to completely retract the awning. Using a 7/16” nut driver and power drill, spin the manual override nut counter- clockwise to retract the awning (Fig 8).
Section 5: Slideout Systems Electric Slide Room(s) (if so equipped) The mechanical components of the slide out are gear driven. Electric powered slideout room systems have a manual override to allow you to extend or retract the slideout room(s) in case of a power loss.
Page 68
Section 5: Slideout Systems To retract the slideout, press the in section of the slideout control switch and hold it until the slideout is fully retracted. Operating the switch after the room is fully extended or retracted may damage the switch and motor.
Page 69
Section 5: Slideout Systems NOTE: For long-term storage it is recommend the room be closed (retracted). Trouble shooting the flush floor slideout Refer to the general troubleshooting check list before proceeding. Electric Operation NOTE: Install transit bars (if so equipped) on the slideout room during storage and transportation.
Page 70
Section 5: Slideout Systems DO NOT attempt to disengage the motor as the actuator is “manual ready”. Schwintek In-Wall Slideout System The in-wall slideout system requires no maintenance or adjustments. This system has two vertical columns with a drive motor located at the top of each column. The right and left motors are synchronized by a circuit board.Schwintek slideouts are typically used on both towables and motorhomes.
Page 71
Section 5: Slideout Systems Trouble shooting the in-wall slideout system Checking Fuses: The in-wall slide requires a minimum 30-amp fuse. Check the load center for blown fuses and replace any if necessary. If the fuse blows immediately upon replace- ment, there is a problem with the wiring to the in-wall slide control box. A qualified service person should be called to check and repair.
Page 72
Section 5: Slideout Systems Using either a wall or command center panel switch, press and hold the switch toward the word IN or RETRACT until the unit comes in completely. This will allow you to get the recreation vehicle to a service center to have the slideout malfunction diag- nosed.
Page 73
Section 5: Slideout Systems Repeat this process for both sides of the slide room. Physically push/ pull the room back into the opening; keep both sides relatively even. The room must be travel locked to keep the room in place for road travel. DO NOT MOVE THE RV UNLESS THE MOTORS ARE PLUGGED IN TO THE CONTROLLER AND THERE IS BATTERY POWER TO THE RV.
Page 74
Section 5: Slideout Systems Norco Slideout Manual Operation Locate the included flexible shaft in your own- er’s packet. Attach flexible shaft to the 1/4” hex fitting on the end of the motor. Attach 1/4” socket & ratchet, or drill to the other end, and turn in the proper direction to move the room.
Page 75
Section 5: Slideout Systems If the room does not move when the switch is pressed, check the following: Make sure the slideout system is turned on. Battery is fully charged and connected. Transit bars have been removed (if so equipped). When the motor brake is disengaged the slideout room WILL NOT lock into place and will not be sealed.
Page 76
Section 5: Slideout Systems The room is now free to move. Using either a 5/8” or 3/4” wrench or socket, crank the room either in or out completely. If the slideout system is supplied with a gearbox override (optional), use the crank handle to move the room.
Page 77
Section 5: Slideout Systems Turn ON the on/off switch or key. Press and hold the OUT button (Fig 4). To retract, press and hold the IN button. There will be a slight delay be- fore the room begins moving. The GREEN LED should be solid ON when room is in motion.
Page 78
Section 5: Slideout Systems -Check all connections at control box and motor. -Bad or loose connec- Excessive -Check the harness for bro- tion Major Battery Volt- ken wires. -Defective harness -Put 12.0 VDC direct to -Open or shorted motor the motor. If it does not run replace the motor.
Page 79
Section 5: Slideout Systems NOTE: After overriding the system, the room control will need to be re-programmed by an OEM authorized dealer. Emergency Retract Mode Use this procedure when there is NO loss of power or electrical problem with the system. Remove the touchpad (Fig 4) from the wall.
Page 80
Section 5: Slideout Systems Unplug the motor from the harness and remove the motor by lifting it up and out. Repeat steps 1-4 for the other side. Place a socket wrench with a 3-inch extension and a 5/8” deep well socket (Fig 12) through the motor access opening and seat the socket onto the coupler (Fig 13).
Page 81
Section 5: Slideout Systems Power Gear Ram Slideout System Typically used for Class C motorhomes. Manual Override Procedure The system has been equipped with 3/4” hex override couplers located on the drive compo- nent of the system. Due to the size and weight of some rooms, assistance may be needed to push the room in.
Page 82
Section 5: Slideout Systems 11. When the slideout is retracted, check to make sure you have a good seal, and re- place the skirting on the slideout. 12. Return the brake release lever back to the “engaged” position (parallel to the spring lock lever).
Section 6: Electrical System The Electrical System The RV electrical system is comprised of two independent electrical systems. One operates off of 12-volt DC power and the other off of 120-volt 60hz AC power. All installations have been made in compliance with industry standards applicable on the date of manufacture. Because the electrical equipment and associated circuitry are engineered into a dedicated system specific to your RV, do not make unauthorized changes or add fixed appliances to it.
Section 6: Electrical System Command Center The command center is typically located inside the entrance door or in the living area of the RV, and contains switches and controls for various electrical functions. Command center applications, configurations and components will vary by model. Command Center Panel or Command Center Panel with Switch Modules Items found on these panels may include:...
Section 6: Electrical System GFCI Receptacle There is a ground fault current interrupter (GFCI) engineered into the electrical system. It is designed to reduce the possible injury caused by electric shock. The GFCI will not protect against short circuits or circuit overloads. Test all GFCI receptacles monthly: Push in the GFCI “TEST”...
Page 86
Section 6: Electrical System Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. DO NOT plug the shore power cord into a campsite receptacle(s): That has reverse polarity With non-functioning ground circuits That shows outward signs of heat damage.
Section 6: Electrical System The shore power cord should be unplugged when the recreation vehicle is left unattended When you are ready to leave, reverse the power cord connection process. Use care to pre- vent damaging the power cord electrical connection pins when connecting or disconnecting the shore power cord.
Page 88
Section 6: Electrical System An open wire between the converter and the RV battery Loose ground connection Improper torques If the converter fuses and AC voltage are good, but the converter output still reads zero volts, the converter is not functioning properly. Modes of Operation: Absorption (Normal) Mode: 13.6VDC range.
Section 6: Electrical System 12-Volt DC System The majority of your recreation vehicle lighting is powered by 12-volt electricity. The 12- volt DC system is composed of components that will operate when the following conditions are met: Power is supplied by the tow vehicle alternator when the engine is running and the 7-way trailer plug is connected.
Section 6: Electrical System Auxiliary Battery (customer supplied) Do not store anything inside the battery compartment(s) or near the batteries that could touch the battery or battery cable terminals. Contact with the battery or battery cable terminals could cause an electrical short circuit, discharge the batteries, or start an electrical fire.
Page 91
Section 6: Electrical System Replacement and Maintenance Some equipment in your RV will draw small amounts of current even when turned OFF. To prevent the auxiliary battery from being discharged when your RV is not connected to shore line power, disconnect the auxiliary battery negative cable at the battery. During storage, it is important to check the voltage monthly and recharge the auxiliary battery as needed.
Section 6: Electrical System Load Center The Load Center contains 12VDC fuses and 120VAC circuit breakers for almost all of the electrical appliances and circuits in the RV. The 120V main breaker may be located in this panel and will turn off all 120-volt power to the RV.
Section 6: Electrical System and must be replaced as needed as part of your RV maintenance. If you have any questions, contact your dealer. A label is provided to explain the function of every 120-volt circuit breaker. This label is located on or near the appropriate load center or sub-panel and must remain permanently affixed to the recreation vehicle.
Page 94
Section 6: Electrical System 120 VOLT SYSTEM Air Conditioner 18 AMPS Coffee Maker 6-12 AMPS Converter (each) 8 AMPS DVD System 3 AMPS Fireplace 15 AMPS Hair Dryer or Curling Iron 10-14 AMPS Microwave 15 AMPS Refrigerator 6 AMPS Satellite Receiver 2 AMPS 2-4 AMPS Vacuum Cleaner...
Page 95
Section 6: Electrical System 50 amp Power Cord Do not hook up the power cord to any receptacle until you have verified proper polarity and grounding. Polarity indicators can be purchased in most electrical and hardware stores. Do not use any cheater plug, adapter or extension cord to reconfigure incoming AC power or break the continuity of the circuit connected to the grounding pin.
Page 96
Section 6: Electrical System Generator The factory-installed generator will produce 120-volt AC power for use when camping in areas where shore power is unavailable. 120-volt power from the generator is output to the AC distribution center by way of a factory-installed automatic transfer switch. In the default mode, the automatic transfer switch connects the generator to the AC distribution center when the generator is operating and shore power is disconnected.
Section 6: Electrical System Excessive cranking can overheat and damage the generator starter motor. Do not crank for more than 20 seconds at a time. Wait at least two minutes before trying again. If the generator does not start after the third try, refer to the gen- erator manufacturer’s user manual for more information.
Section 6: Electrical System LED Decorative Light Strips (if so equipped) Some models may include decorative LED light strips which may be installed on the awning or on the front cap. When the awning light switch is turned on, these LED light strips il- luminate.
Section 7: Fuel & Propane System Exhaust Gas Fumes Avoid inhaling exhaust gases as they contain carbon monoxide, which is a potentially toxic gas that is colorless and odorless. If you are in a recreation vehicle with either a nearby tow vehicle engine running or the generator (if so equipped) running there is a potential for exhaust fumes to filter back into the recreation vehicle.
Page 100
Section 7: Fuel & Propane System Continued periodic checks of the propane system at 5,000 miles of travel (or at least once a year), by a qualified propane service representative as part of your normal maintenance is recommended. Hand tighten the LP gas system valves only, do not use a wrench or pliers as over tightening may damage the valve seals and cause them to leak.
Page 101
Section 7: Fuel & Propane System Be sure to securely re-install DOT cylinder(s) after they have been removed for filling or replacement. Always close the service valve and install a dust cap or plug when transporting or storing disconnected containers whether full or empty. ASME tanks are permanently mounted to the RV and are commonly used on RV mo- torhomes.
Page 102
Section 7: Fuel & Propane System The position of the propane container(s) and the hoses are critical to proper operation and propane flow. Follow these instructions to make sure your propane container(s) are connected properly. LP Gas Container Overfill Never allow your propane tank to be filled above the maximum safe level as indicated by the fixed liquid level gauge.
Page 103
Section 7: Fuel & Propane System Fittings are used to connect the various system components to each other. The P.O.L. fitting at the end of the propane supply hose is made of brass so that pipe sealants are not necessary to prevent leaking.
Section 7: Fuel & Propane System Propane Use and Safety Propane is a colorless and odorless gas that, in the lique- fied state, resembles water. An odorant (usually a sulfur compound) is added as a warning agent. If you smell propane within the vehicle, quickly and carefully per- form the procedure listed on the propane system label.
Page 105
Section 7: Fuel & Propane System tally exhausted. Using one cylinder until it is empty and then using the second cylinder will allow you to fill the empty cylinder at your convenience without running out of propane. Cooking With Propane Gas Do not turn gas range burner controls to ON and allow gas to escape before lighting.
Section 7: Fuel & Propane System Traveling With Propane NOTE: Some states prohibit propane appliances to be oper- ated during travel, especially in underground tunnels. Know the laws for the areas where you travel. Use care when fueling your motor fuel tanks and/or propane containers.
Page 107
Section 7: Fuel & Propane System Attach the 1/4” inverted flare x 24” Type 1 pigtail hose to the regulator inlet and the right hand swivel nut to the cylinder valve. Secure the cylinder to the A-frame bracket using the bolts, nuts and washers provided. Double Cylinder Mounted On A-Frame (if so equipped) When a second cylinder is installed, a tee check valve is used to replace the 90°...
Page 108
Section 7: Fuel & Propane System Notes: Maintenance Record Table of Contents...
Section 8: Plumbing System Plumbing System There are two different water systems in your recreation vehicle: The fresh water system consists of the fresh water holding tank, faucets and con- nections, water pump, outside shower assembly (if so equipped), water heater, tub/ shower, and water purification system (if so equipped).
Page 110
Section 8: Plumbing System Operation Press only one tact switch at a time. As you push either the FRESH, BLK GREY1 or GREY2 switch, one or more LED lights will illuminate (from left to right) indicating the content level for that tank. When pushing the “BATT” switch, the LED lights illuminate from left (lowest) to right (highest) to indicate the estimated auxiliary battery condi- tion.
Section 8: Plumbing System NOTE: This light will not appear on touchscreens, RV remote con- trols or on a Wi-Fi app, only on the Command Center switch panel. Fresh Water System All water contains contaminant and mineral particles that can cause fresh water system odors.
Section 8: Plumbing System 12-volt Water Pump and Switch There must be sufficient 12-volt DC power to run the water pump when your recreation vehicle is not hooked up to city water. Once activated, the water pump (also known as the demand pump) will self-prime, and provide water.
Section 8: Plumbing System old filter properly). Clean the inside of the filter housing with mild detergent. Thoroughly rinse and wipe clean. Remove the O-ring from the groove in the housing and wipe clean. Coat with petro- leum jelly. Replace the O-ring in the groove, making sure it is properly seated. Install the new filter cartridge.
Page 114
Section 8: Plumbing System Open the “fresh tank drain” valve. All fresh water tanks can be drained by one of two types of drain valves. A white plastic drain is attached to the exterior wall or a valve located inside the RV adjacent to the water tank (turn 45°...
Page 115
Section 8: Plumbing System NOTE: There are also 2 water valves which are typically located near the water pump. One is a fresh water tank shutoff, and the other one is a siphon valve used for winterizing the plumbing system. Siphon valve will have a clear plastic hose attached to it.
Page 116
Section 8: Plumbing System NOTE: In the 3-valve bypass diagram, valve D is the fresh water tank shutoff. Valve E is used to introduce RV antifreeze into the lines when winterizing the system and has a clear hose attached to it. See Winterizing the Plumbing System.
Page 117
Section 8: Plumbing System There are two valves at the water pump location. The water tank shutoff valve (D) should be in the OFF position (Fig 2). Siphon valve (E)) should be in the OFF posi- tion (points away from clear hose). Fig 2 shows the siphon valve in the ON position. (Siphon valve is connected to the clear plastic hose).
Page 118
Section 8: Plumbing System / tank fill valve at the utility center is not used for this operation. It can remain in the CITY position. Refer to Winterizing the Plumbing System. Sanitizing (with 6 in 1 Utility Center) When to sanitize: When your RV is new.
Page 119
Section 8: Plumbing System NOTE: To thoroughly sanitize the fresh water tank, the unit should be driven around for a short while allowing the solution to splash the sides and top of the fresh water tank. 13. After sanitizing, drain the chlorine solution from the fresh water system. Refer to Draining the Fresh Water System section.
Page 120
Section 8: Plumbing System Close low point drains and fresh water tank drain. Refill the fresh water tank with clean potable water. Use either the power fill tank method or gravity fill inlet on the trailer as explained previously. Turn water tank shutoff valve (at the pump) ON. Turn the pump ON. Open faucets and check that the chlorine taste is gone.
Page 121
Section 8: Plumbing System Automotive antifreeze (ethylene glycol) and windshield washer anti- freeze (methanol) are poisonous. Never use these products in your fresh water system. These products are harmful and may be fatal if swallowed Never apply air pressure to the water system with any of the valves in the closed position.
Page 122
Section 8: Plumbing System 12. Finish blowing air into the water lines to evacuate all water from the lines. This can take 5 to 10 minutes. 13. Winterize appliances (if applicable). 14. Pour one cup of RV antifreeze in all the drain P-traps (sinks and bathtub). 15.
Section 8: Plumbing System 12. To prevent staining, wipe the RV antifreeze out of the sinks, shower (or tub) and toilet using a soft, dry cloth. In the spring when flushing antifreeze out of the lines: Set the city water valve at the utility center to the CITY position. Attach a pressurized water source to the fresh water inlet on the utility center.
Page 124
Section 8: Plumbing System Make sure the water heater is filled with water before use as even momentary operation of the water heater without water in it may result in damage to the tank heating element and/or controls. Double check the bypass valves, make sure they are set properly. Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water heater.
Section 8: Plumbing System Turn off the water heater. Turn off the cold water supply line. Open a faucet in the recreation vehicle. Pull out the handle of the pressure relief (P&T) valve and allow water to flow from the valve until it stops.
Section 8: Plumbing System Faucets The bathroom, kitchen and outside shower faucets operate much the same way as the faucets in your home. Make sure there is sufficient water available and the 12-volt water pump is turned ON before operating. NOTE: There may be air in the water plumbing lines which needs to be bled out before a steady stream of water comes from the faucet.
Page 127
Section 8: Plumbing System tents faster and will keep the drain lines and tanks clean and free flowing. These chemicals are avail- able at an RV supply store or your dealer. Drain Pipes with Dry Sealing Valve (if so equipped) Your RV may be equipped with a dry sealing valve that prevents the escape of odors from your waste system and eliminates the need for P-traps.
Page 128
Section 8: Plumbing System Never travel with full black or grey water holding tanks. This not only wastes your fuel but depending on the location of the tank(s), it can affect your tow vehicle handling characteristics. Never leave the black tank drain in the open position continuously when connected to the campground sewer system.
Section 8: Plumbing System Sewage (black) tank preparation It is important to add enough water to prevent solid waste buildup. Follow the directions listed below and in the manufacturer’s operator manual. Release one to two quarts (1 or 2 liters) of water into the toilet bowl. Follow the directions on your RV-approved toilet chemical bottle (customer supplied) and put the recommended quantity of holding tank chemical into the toilet bowl.
Section 8: Plumbing System The tank heater switch should be turned ON: When liquid is present in the holding tanks and the outside temperature approach- es and maintains freezing conditions 35°F (2°C) or colder. The tank heater switch should be turned OFF: When there is NO liquid present (tanks are empty).
Page 131
Section 8: Plumbing System Sewage (black) tank preparation Release one to two quarts (1 or 2 liters) of water into the toilet bowl. Follow the directions on your (approved RV) toilet chemical bottle (customer sup- plied), by placing the recommended quantity of holding tank chemical into the toilet bowl.
Page 132
Section 8: Plumbing System Notes: Maintenance Record Table of Contents...
Section 9: Heating and Cooling Air Conditioner The air conditioning system is controlled by a thermostat. Cooled air enters the RV through the grill. Make sure you have sufficient power available before operating the air conditioner. Do not operate the air conditioner without the return air filter. Operating the system without the filter allows the lint and dirt that is normally stopped by the filter to accumulate on the cooling coil of the air conditioner.
Section 9: Heating and Cooling NOTE: For RV models with touch screens, the powered roof vent(s) may be controlled on one of the selectable screens on the touch screen. Furnace The furnace installed in your recreation vehicle is controlled by a 12-volt DC thermostat. Depending on your model, there may be up to two thermostats enabling you to control the temperature to your comfort level.
Section 10: Appliances Microwave To prevent damage, remove the turntable from the microwave when trav- eling. Make sure you are connected to a 120-volt power source. Never use the microwave cavity for storage. The microwave cavity should always be empty when not in use. For details on operation, cleaning and safety information, refer to the manufacturer’s user guide.
Page 136
Section 10: Appliances Cooking With Propane (if so equipped) See the Propane System Section for important safety instructions. Refer to the manufactur- er’s owner’s manual for detailed operating and safety instructions for all propane appliances. Cooktops, Range and Oven (if so equipped) For detailed operating and safety information, refer to the manufacturer’s user guide.
Page 137
Section 10: Appliances Do not use aluminum foil on the electric range cooktop, as this material will damage the cooktop surface if it melts. Do not use aluminum foil under any circumstances on the electric range cooktop. Gas Drop-In Cooktops (if so equipped) Depending on your model, it may be equipped with either a 2 burner or 3 burner cooktop.
Page 138
Section 10: Appliances LP Gas Grill Hookup (if so equipped) Gas BBQ Grill Prep (if so equipped) Your recreation vehicle may be equipped with a propane “quick-coupler” connection and support bracket for easy installation of the BBQ grill. Typically this connection is located at the LP tank bracket.
Section 10: Appliances Range Hood (if so equipped) If your recreational vehicle is equipped with a range hood, it will be connected to an exterior vent. The vent has an inner flap with two snaps. This flap can be snapped shut when the vehicle is in motion, or during storage to keep insects, debris, snow, rain, etc.
Page 140
Section 10: Appliances The ice maker (if so equipped) should be turned off and the ice tray emptied when power to your recreation vehicle has been shut off. With no power, the ice will melt and water may “pool” in the refrigerator door. When power is restored, the vibration may cause this water to run out of the door and on to the vehicle floor.
Page 141
Section 10: Appliances If you need to clean the condenser: Remove the base grille. Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area of the condenser. Replace the base grille when finished.
Page 142
Section 10: Appliances Attaching the “quick coupler” connection The “quick coupler” is directly connected to the RV propane system. The “quick-coupler” con- nection has a positive shut-off valve as required by code and standards. Place the “quick coupler handle in the OFF Quick Connect Coupler position and push back the sleeve.
Page 143
Section 10: Appliances The grill requires proper ventilation. It is designed for RV outdoor use only. NEVER put lava rocks or charcoal or anything else on or under the grate. Grill is designed so it does not require those items. Serious injury or property damage can occur by placing foreign objects on the grate.
Page 144
Section 10: Appliances Notes: Maintenance Record Table of Contents...
Page 145
Section 11: Electronics Antenna HDTV Antenna (if so equipped) Your recreation vehicle may be equipped with an exterior fixed position High Definition TV antenna (HDTV). The an- tenna is capable of receiving any Over-The-Air (OTA) high definition television signals being broadcast in your receiv- ing area.
Page 146
Section 11: Electronics Notes: Maintenance Record Table of Contents...
Section 12: Interior Cleaning The Interior To keep the value of your recreation vehicle, perform regular maintenance using the proper materials and procedures. Using the wrong cleaner may result in damage to the surfaces in your vehicle. Check with the manufacturer’s information for the recommended cleaning agent.
Page 148
Section 12: Interior Fill a spray bottle with water and a tiny amount of soap. Then spray a lint-free towel with the mixture and use the towel to wipe down each slat. While cleaning, try not to bend the slats. They can also be soaked in a bathtub to loosen up any debris so the slats can be wiped down easily.
Page 149
Section 12: Interior NOTE: Oil based soaps and cleaners are not recommended. No abrasive cleaners or alcohol cleansers should be used. If other cleaner solutions are used, first try on a spot in an inconspicuous area. Sofa and Dinette Your recreation vehicle may be equipped with one of the following sofa styles. Hide-A-Bed Sofa or Sofa Sleeper The hide-a-bed sofa functions much the same as a regular residential hide-a-bed sofa.
Page 150
Section 12: Interior Cube Sofa The Cube Sofa functions similar to a residential futon. The slanted back pillows offer nu- merous options as a sofa, along with the ability to extend the cushions for additional sleeping space. Booth Dinette (if so equipped) The dinette is designed to seat up to four adults.
Section 12: Interior Pantry or Hutch (if so equipped) Your recreation vehicle may have a pantry or hutch that you can use for storage. Make sure all items stored in the pantry or hutch are secured to prevent shifting during travel. This cabinetry has been designed to accommodate the normal camping items which may be bulky but not necessarily heavy.
Section 12: Interior Run cold water when pouring hot/boiling water into the sink. Solid surface sink maintenance Occasionally, clean the solid surface sink by filling one-quarter full with a 50/50 water/ bleach solution. Let soak for 15 minutes, and then wash sides and bottom of sink as solu- tion drains.
Page 153
Section 12: Interior Before lifting, be sure there is nothing on the bed that will restrict its movement or add extra weight. Use caution when opening or closing the bed to keep hands and fin- gers at the end ledge provided (not on the side or farther back than necessary).
Page 154
Section 12: Interior NOTE: Some types of bunk beds will not have a ladder. Exercise extreme care when entering or exiting the bunk beds and using the ladder (if so equipped). Do not allow more than one person on the top bunk. Do not allow children under 6 years of age to use the upper bunk.
Section 13: Exterior Cleaning The Exterior To protect your recreation vehicle’s exterior finish, wash it often and thoroughly. For recreation vehicles with painted exterior graphics, if desired you may wash and wax your vehicle 60 days after purchase. The exterior paint needs time to cure before any wax is applied to the exterior surface.
Page 156
Section 13: Exterior Drying the recreation vehicle is just as important as washing your vehicle. Tap and well water contain many chemicals that could water stain your vehicle’s finish. We suggest using a damp natural or synthetic chamois. Other drying products such as lint-free micro-fiber towels work as well.
Section 13: Exterior in one direction. After polishing, flush the compound from the surface and apply a coat of wax to regain a beautiful luster. Damaged paint To prevent corrosion, touch up small cracks and scratches in the paint coat as soon as pos- sible with touch-up film or paint.
Section 13: Exterior Exterior Roof and Sidewall Vents Inspect the roof vents, including sealants for cracks and keep them clean. Inspect the refrig- erator and holding tank vents for blockages from bird nests, spider webs, leaves, etc. All exterior access doors and vents need to be kept clean and free of obstructions (i.e., insect nests, mud daubers, etc.) while the appliances are in use.
Page 159
Section 13: Exterior LADDER CAPACITY MAXIMUM 300 lbs (136 kg) DO NOT exceed the ladder maximum weight rating. The maximum rating includes the person’s weight PLUS weight of items carried. When climbing: • Always face the ladder. • Climb slowly with weight centered between side rails. •...
Page 160
Section 13: Exterior The sealants may become damaged due to road vibration, ultraviolet exposure, air pollution, freezing temperatures and exposure to other elements. If deteriorated, repair immediately to prevent damage. If you notice water inside the recreation vehicle, immediately have the dealer check for the source of the leak.
Section 14: Travel/Camping/Storage Checklists Travel Checklist Following is a preliminary list of items that need to be checked before leaving your home or campsite. This is a general list, which you may want to customize as you determine your own needs. Safety Make sure you follow all safety precautions noted in this owner’s manual and in any manufacturer’s operators manual when preparing to travel.
Page 162
Section 14: Travel/Camping/Storage Checklists Before leaving the campsite Check the area under the RV after overnight parking and look for water or other fluid leaks. If leaks are detected, find the cause and correct it immediately. Turn off propane tanks. Empty black and gray holding tanks, rinse as needed (if so equipped).
Page 163
Section 14: Travel/Camping/Storage Checklists Close the propane cylinder valve(s). We recommend using a propane cylinder cover, and to make sure the propane regulator is covered. If is equipped with a gas/ electric DSI range, light a range gas burner to consume any gas remaining in the lines.
Page 164
Section 14: Travel/Camping/Storage Checklists Notes: Maintenance Record Table of Contents...
Your recreation vehicle may be equipped with some of the items listed below. This is a partial listing and it is not intended to cover all components. All information is the latest available at the time of publication. Starcraft reserves the right to change any of the follow- ing information without notice.
Page 166
Section 15: Additional Information Tank Sprayer/BLK B & B Molders www.bandbmolders.com Thermostat Coleman Mach www.airxcel.com/coleman-mach Toilet Thetford Corp. www.thetford.com See manufacturers’ user guide TV Antenna Winegard Company www.winegard.com Water Heater, Tank DSI Atwood Greenbrier www.atwoodmobile.com Water Heater, Tankless Girard Systems www.greenrvproducts.com Water Pump, 12V Shurflo East...
Section 15: Additional Information Vehicle Maintenance Record Make: Model: Model Year: Vehicle Serial#: Service Performed Mileage Work Performed Notes Date Maintenance Record Table of Contents...
Page 168
Section 15: Additional Information Service Performed Mileage Work Performed Notes Date Maintenance Record Table of Contents...
Page 169
Section 15: Additional Information Starcraft Ownership Notification Fax Form To: (574) 825-6092 ATTENTION! Federal record keeping laws require that we maintain a file of owners of our product. Your cooperation in filling out this from will be appreciated. □ □...
Need help?
Do you have a question about the Telluride 2021 and is the answer not in the manual?
Questions and answers