Page 1: Table Of Contents
Yamatake Corporation Digital Controller SIO Driver System Configuration....................... 3 Selection of External Device .................... 9 Example of Communication Setting ................10 Setup Items ........................74 Cable Diagram ....................... 79 Supported Devices....................... 138 Device Code and Address Code.................. 152 Error Messages......................156...
Page 2 Digital Controller SIO Driver Introduction This manual describes how to connect the Display and the External Device (target controller). In this manual, the connection procedure will be described by following the sections below: System Configuration "1 System Configuration" (page 3) This section shows the types of External Devices that can be connected and SIO type.
Page 3: System Configuration
Digital Controller SIO Driver System Configuration The following shows the system configuration where the External Device from Yamatake Corporation and the Display are connected. Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable Terminal block on RS422/485 SDC10...
Page 4 Digital Controller SIO Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable Terminal block on C40B RS232C Example 13 Diagram 1 the controller (page 34) (page 79) Setting Cable RS422/485 SDC40B Example 14 Diagram 2 (4wire) (page 36) (page 81) Terminal block on C40B...
Page 5 Digital Controller SIO Driver Setting Cable Series Link I/F SIO Type Example Diagram Setting Cable RS232C Example 23 Diagram 1 (page 54) (page 79) Setting Cable Terminal block on RS422/485 DCP551 DCP551 Example 24 Diagram 2 the controller (4wire) (page 56) (page 81) Setting Cable...
Page 6 Digital Controller SIO Driver Connection Configuration • 1:1 Connection Display External Device • 1:n Connection Maximun 16 units Display External External External Device Device Device • 1:n Connection (when CMC10B is used) Up to 16 units of CMC10B can be connected to one Display. In addition, up to 31 External Devices that support CPL communication can be connected to CMC10B.CMC10B always collects set data, allowing improved communication performance when many devices are connected.
Page 7 Digital Controller SIO Driver IPC COM Port When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please refer to the IPC manual for details. Usable port Usable Port Series RS-232C RS-422/485(4 wire) RS-422/485(2 wire) COM1 , COM2,...
Page 8 Digital Controller SIO Driver DIP switch setting: RS-422/485 (4 wire) DIP switch Setting Description Reserved (always OFF) SIO type: RS-422/485 Output mode of SD (TXD) data: Always output Terminal resistance (220Ω) insertion to SD (TXD): None Terminal resistance (220Ω) insertion to RD (RXD): None Short-circuit of SDA (TXA) and RDA (RXA): Not available Short-circuit of SDB (TXB) and RDB (RXB): Not available RS (RTS) Auto control mode: Disabled...
Page 9: Selection Of External Device
Setup Items Setup Description Maker Select the maker of the External Device to be connected. Select "Yamatake Corporation". Select the model (series) of the External Device to be connected and its connection method. Select "Digital Controller SIO". Check the External Device that can be connected in "Digital Controller SIO" in system Series configuration.
Page 10: Example Of Communication Setting
Digital Controller SIO Driver Example of Communication Setting The following shows examples of communication settings for the Display and the External Device, which are recommended by Pro-face. Setting Example 1 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. •...
Page 11 Digital Controller SIO Driver Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings]. Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, Down and Up keys on the front of the Controller.
Page 12 Digital Controller SIO Driver Setting Example 2 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 13 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, mode, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the operation display, press and hold the PARA key (for 2 seconds) to move to the parameter setting display. In the parameter setting display, press and hold the PARA key (for 2 seconds) to move to the setup display.
Page 14 Digital Controller SIO Driver Setting Example 3 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 15 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press and hold the ENT and Down keys simultaneously (for 3 seconds or more) to display the setup items.
Page 16 Digital Controller SIO Driver Setting Example 4 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 17 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press and hold the ENT and Down keys simultaneously (for 3 seconds or more) to display the setup items.
Page 18 Digital Controller SIO Driver Setting Example 5 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 19 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press and hold the ENT and Down keys simultaneously (for 3 seconds or more) to display the setup items.
Page 20 Digital Controller SIO Driver Setting Example 6 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 21 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the para, mode, enter, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the operation display, press and hold the para key (for 2 seconds) to move to the bank selection display. In the bank selection display, press the enter key to move to the bank setup display.
Page 22 Digital Controller SIO Driver Setting Example 7 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 23 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the ENT, DISP, MODE, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 24 Digital Controller SIO Driver Setting Example 8 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 25 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the ENT, DISP, MODE, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 26 Digital Controller SIO Driver Setting Example 9 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 27 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the para, mode, enter, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the operation display, press and hold the para key (for 2 seconds) to move to the bank selection display. In the bank selection display, press the enter key to move to the bank setup display.
Page 28 Digital Controller SIO Driver 3.10 Setting Example 10 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 29 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 30 Digital Controller SIO Driver 3.11 Setting Example 11 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 31 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 32 Digital Controller SIO Driver 3.12 Setting Example 12 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 33 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 34 Digital Controller SIO Driver 3.13 Setting Example 13 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 35 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key to move to setup mode. Press the ENT key to display the setup items.
Page 36 Digital Controller SIO Driver 3.14 Setting Example 14 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 37 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key to move to setup mode. Press the ENT key to display the setup items.
Page 38 Digital Controller SIO Driver 3.15 Setting Example 15 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 39 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key to move to setup mode. Press the ENT key to display the setup items.
Page 40 Digital Controller SIO Driver 3.16 Setting Example 16 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 41 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 42 Digital Controller SIO Driver 3.17 Setting Example 17 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 43 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PARA, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode. Switch the External Device to READY mode before setting.
Page 44 Digital Controller SIO Driver 3.18 Setting Example 18 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 45 Digital Controller SIO Driver Settings of External Device Use the ladder software to configure communication settings for the External Device. (Operation confirmed using the the Smart Loader Package SLP-D10 V3.0.1.) Set the device address of the External Device using the rotary switch on the front of the Controller.
Page 46 Digital Controller SIO Driver 3.19 Setting Example 19 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 47 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the FUNC, PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key while holding down the FUNC key to move to the setting group selection screen.
Page 48 Digital Controller SIO Driver 3.20 Setting Example 20 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 49 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the FUNC, PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key while holding down the FUNC key to move to the setting group selection screen.
Page 50 Digital Controller SIO Driver 3.21 Setting Example 21 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 51 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the FUNC, PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key while holding down the FUNC key to move to the setting group selection screen.
Page 52 Digital Controller SIO Driver 3.22 Setting Example 22 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 53 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the FUNC, PARA, ENT, DISP, Down and Up keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the basic display, press the PARA key while holding down the FUNC key to move to the setting group selection screen.
Page 54 Digital Controller SIO Driver 3.23 Setting Example 23 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 55 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 56 Digital Controller SIO Driver 3.24 Setting Example 24 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 57 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 58 Digital Controller SIO Driver 3.25 Setting Example 25 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 59 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 60 Digital Controller SIO Driver 3.26 Setting Example 26 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 61 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 62 Digital Controller SIO Driver 3.27 Setting Example 27 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 63 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 64 Digital Controller SIO Driver 3.28 Setting Example 28 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 65 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the PROG, RUN/HOLD, SETUP, ENT, DISP, Down and Up keys on the front of the Controller. You can change the communication settings only in READY mode.
Page 66 Digital Controller SIO Driver 3.29 Setting Example 29 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 67 Digital Controller SIO Driver Settings of External Device To configure communication settings for the External Device, use the para, enter, display, and cursor keys on the front of the Controller. Refer to your Controller manual for details. Procedure In the operation display, press and hold the para key (for 2 seconds) to move to PARA bank mode. Press the para key to display RS-485 communication bank mode (rS485).
Page 68 Digital Controller SIO Driver 3.30 Setting Example 30 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 69 Digital Controller SIO Driver Settings of External Device Use the ladder software (Smart Loader Package SLP-D510 V2.2.3) to configure communication settings for the External Device. Use the rotary switch on the front of the Controller to set the device address of the External Device.
Page 70 Digital Controller SIO Driver 3.31 Setting Example 31 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 71 Digital Controller SIO Driver Settings of External Device Use the ladder software (Smart Loader Package SLP-D510 V2.2.3) to configure communication settings for the External Device. Use the rotary switch on the front of the Controller to set the device address of the External Device.
Page 72 Digital Controller SIO Driver 3.32 Setting Example 32 Setting of GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace. Device Setting To display the setting screen, click ([Setting]) of the External Device you want to set from [Device-Specific Settings] of [Device/PLC Settings].
Page 73 Digital Controller SIO Driver Settings of External Device Use the ladder software (Smart Loader Package SLP-CM1 V2.0.1) to configure communication settings for the External Device. Use the rotary switch on the front of the Controller to set the device address and transmission speed of the External Device.
Page 74: Setup Items
Digital Controller SIO Driver Setup Items Set the communication settings of the Display with GP-Pro Ex or in off-line mode of the Display. The setting of each parameter must match that of the External Device. "3 Example of Communication Setting" (page 10) Setup Items in GP-Pro EX Communication Settings To display the setting screen, select [Device/PLC Settings] from [System setting window] in the workspace.
Page 75 Digital Controller SIO Driver Setup Items Setup Description In case of no response from the External Device, enter how many times the Display Retry retransmits the command, from "0 to 255". Enter the standby time (ms) from when the Display receives packets until it transmits the Wait To Send next command, from "0 to 255".
Page 76 Digital Controller SIO Driver Settings in Off-Line Mode • Refer to the Maintenance/Troubleshooting manual for information on how to enter off-line mode or about the operation. Maintenance/Troubleshooting Manual "Off-line Mode" • The number of the setup items to be displayed for 1 page in the off-line mode depends on the Display in use.
Page 77 Digital Controller SIO Driver Setup Items Setup Description Displays the communication control method to prevent overflow of transmission and Flow Control reception data. Enter the time (s) for which the Display waits for a response from the External Device, Timeout from "1 to 127".
Page 78 Digital Controller SIO Driver Option To display the setting screen, touch [Device/PLC Settings] from [Peripheral Equipment Settings]. Touch the External Device you want to set from the list that appears, and touch [Option]. Setup Items Setup Description Switches between RI/VCC of the 9th pin. RI/VCC To connect to the IPC, you need to switch between RI/5V using the IPC selector switch.
Page 79: Cable Diagram
Digital Controller SIO Driver Cable Diagram The cable diagram shown below may differ from that recommended by Yamatake Corporation. Please be assured, however, that there is no operational problem in applying the cable diagram shown in this manual. • The FG pin on the External Device must be D-class grounded. Refer to your External Device manual for details.
Page 80 Digital Controller SIO Driver Controller D-Sub 9 Pin (socket) Shield Terminal Block Signal name Signal name RD(RXD) Display SD(TXD) ER(DTR) DR(DSR) RS(RTS) CS(CTS) Display side Controller Terminal block Shield Terminal Block Signal name Signal name RD(RXD) Display SD(TXD) ER(DTR) DR(DSR) RS(RTS) CS(CTS) GP-Pro EX Device/PLC Connection Manual...
Page 81 Digital Controller SIO Driver Cable Diagram 2 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Connector terminal block conversion adapter by Pro-face (COM2) CA3-ADPTRM-01 LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Cable length: 500m or less...
Page 82 Digital Controller SIO Driver • 1:1 Connection Terminal Terminal resistance Controller resistance 150Ω ±5% Terminal block 150Ω ±5% (more than (more than Shield Signal name Signal name 1/2W) 1/2W) Display CA3-ADPCOM-01 CA3-ADPTRM-01 Terminal Terminal resistance resistance 150Ω ±5% 150Ω ±5% TERM (more than (more than...
Page 83 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal D-Sub 9 Pin (socket) Terminal block resistance 150Ω ±5% (more than Shield 150Ω ±5% Signal name Signal name (more than 1/2W) 1/2W) Display Terminal resistance Terminal resistance 150Ω ±5% 150Ω...
Page 84 Digital Controller SIO Driver • 1:1 Connection Terminal Terminal Controller resistance resistance Terminal block 150Ω ±5% 150Ω ±5% (more than (more than Shield Signal name Signal name 1/2W) 1/2W) Display CA4-ADPONL-01 CA3-ADPTRM-01 Terminal Terminal resistance resistance 150Ω ±5% 150Ω ±5% TERM (more than (more than...
Page 85 Digital Controller SIO Driver • 1:1 Connection Terminal D-Sub 9 Pin (plug) Controller resistance Terminal Signal name Terminal block 150Ω ±5% resistance (more than Shield 150Ω ±5% TERMRX Signal name 1/2W) (more than 1/2W) Display CA4-ADPONL-01 Terminal Terminal resistance resistance 150Ω...
Page 86 Digital Controller SIO Driver • 1:1 Connection Terminal Display side Controller resistance Terminal block Terminal block 150Ω ±5% (more than Shield Terminal Signal name Signal name resistance*1 1/2W) Display Terminal Terminal resistance*1 resistance 150Ω ±5% (more than 1/2W) • 1:n Connection Terminal Display side Controller...
Page 87 Digital Controller SIO Driver Cable Diagram 3 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01...
Page 88 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Shield 1/2W) (more than 1/2W) Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Controller Controller resistance Terminal...
Page 89 Digital Controller SIO Driver • 1:1 Connection Terminal resistance Controller Terminal D-Sub 9 Pin (socket) Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Shield 1/2W) (more than 1/2W) Display Shell • 1:n Connection Terminal Controller Controller resistance Terminal...
Page 90 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Shield (more than 1/2W) 1/2W) Display CA4-ADPONL-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Controller Controller resistance Terminal...
Page 91 Digital Controller SIO Driver • 1:1 Connection Terminal D-Sub 9 Pin (plug) Controller resistance Terminal Signal name Terminal block resistance 150W ±5% (more than 150W ±5% TERMRX Signal name Shield (more than 1/2W) 1/2W) Display CA4-ADPONL-01 TERMTX Shell User-created cable •...
Page 92 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Signal name Signal name Shield 1/2W) (more than 1/2W) Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM TERM User-created cable •...
Page 93 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal D-Sub 9 Pin (socket) Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Shield 1/2W) (more than DATA+ 1/2W) DATA- Display GND (SG) Shell • 1:n Connection Terminal Controller...
Page 94 Digital Controller SIO Driver • 1:1 Connection Terminal Display side resistance Controller Terminal block Terminal block 150Ω ±5% (more than Signal name Terminal Signal name Shield 1/2W) resistance*1 Display • 1:n Connection Terminal Display side Controller Controller resistance Terminal block Terminal block Terminal block 150Ω...
Page 95 Digital Controller SIO Driver • 1:1 Connection Terminal Display side Controller resistance Terminal D-Sub 9pin (plug) Terminal block 150Ω ±5% resistance (more than 150Ω ±5% Signal name Signal name Shield 1/2W) (more than LINE(+) 1/2W) LINE(-) Display GND(SG) RS(RTS) Shell •...
Page 96 Digital Controller SIO Driver Cable Diagram 4 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01...
Page 97 Digital Controller SIO Driver • 1:1 Connection Signal name Shield Controller Terminal block Display Signal name CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Signal name Shield Controller Controller Shield Terminal block Terminal block Display Signal name Signal name...
Page 98 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 Pin (socket) Signal name Shield Controller Terminal block Signal name Display Shell • No termination resistor is required. • 1:n Connection D-Sub 9 Pin (socket) Signal name Shield Controller Controller Shield Terminal block Terminal block Signal name...
Page 99 Digital Controller SIO Driver • 1:1 Connection Signal name Shield Controller Terminal block Display Signal name CA4-ADPONL-01 CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Signal name Shield Controller Controller Shield Terminal block Terminal block Display Signal name Signal name...
Page 100 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 Pin (plug) Signal name TERMRX Shield Controller CA4-ADPONL-01 Terminal block Display Signal name TERMTX Shell User-created cable • No termination resistor is required. • 1:n Connection D-Sub 9 Pin (plug) Signal name TERMRX Shield Controller...
Page 101 Digital Controller SIO Driver • 1:1 Connection Controller Terminal block Signal name Signal name Shield Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Controller Controller Shield Terminal block Terminal block Signal name Signal name Signal name Shield Display...
Page 102 Digital Controller SIO Driver • 1:1 Connection Controller Terminal block D-Sub 9 Pin (socket) Signal name Signal name Shield DATA+ DATA- Display GND (SG) Shell • No termination resistor is required. • 1:n Connection Controller Controller Shield Terminal block Terminal block D-Sub 9 Pin (socket) Signal name Signal name...
Page 103 Digital Controller SIO Driver • 1:1 Connection Display side Terminal block Signal name Shield Controller Terminal block Signal name Display • No termination resistor is required. • 1:n Connection Display side Terminal block Signal name Shield Controller Controller Shield Terminal block Terminal block Signal name Signal name...
Page 104 Digital Controller SIO Driver • 1:1 Connection Display side Controller D-Sub 9pin (plug) Terminal block Signal name Signal name Shield LINE(+) LINE(-) Display GND(SG) RS(RTS) Shell • No termination resistor is required. • 1:n Connection Display side Controller Controller Shield D-Sub 9pin (plug) Terminal block Terminal block...
Page 105 Digital Controller SIO Driver Cable Diagram 5 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01...
Page 106 Digital Controller SIO Driver • 1:1 Connection Terminal resistance 150Ω ±5% Terminal Signal name Shield (more than Controller resistance 1/2W) Terminal block 150Ω ±5% Display (more than CA3-ADPCOM-01 Signal name 1/2W) CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal resistance 150Ω...
Page 107 Digital Controller SIO Driver • 1:1 Connection Terminal D-Sub 9 Pin (socket) resistance 150Ω ±5% Terminal Signal name Shield (more than Controller resistance Terminal block 1/2W) 150Ω ±5% (more than Signal name 1/2W) Display Shell • 1:n Connection Terminal D-Sub 9 Pin (socket) resistance 150Ω...
Page 108 Digital Controller SIO Driver • 1:1 Connection Terminal resistance 150Ω ±5% Terminal Signal name Shield (more than Controller resistance 1/2W) Terminal block 150Ω ±5% Display (more than CA4-ADPONL-01 Signal name 1/2W) CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal resistance 150Ω...
Page 109 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 Pin (plug) Terminal resistance Signal name 150Ω ±5% Terminal TERMRX Shield (more than Controller resistance 1/2W) Display Terminal block 150Ω ±5% (more than Signal name 1/2W) CA4-ADPONL-01 TERMTX Shell User-created cable •...
Page 110 Digital Controller SIO Driver • 1:1 Connection Terminal Controller Terminal resistance resistance Terminal block 150Ω ±5% 150Ω ±5% (more than Signal name Signal name Shield (more than 1/2W) 1/2W) Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Controller Controller resistance Terminal...
Page 111 Digital Controller SIO Driver • 1:1 Connection Terminal Controller resistance Terminal D-Sub 9 Pin (socket) Terminal block resistance 150Ω ±5% (more than 150Ω ±5% Signal name Signal name Shield (more than 1/2W) DATA+ 1/2W) DATA- Display GND (SG) Shell • 1:n Connection Terminal Controller...
Page 112 Digital Controller SIO Driver • 1:1 Connection Display side Terminal block Terminal Terminal Signal name Shield Controller resistance resistance*1 Terminal block 150Ω ±5% (more than Signal name 1/2W) Display • 1:n Connection Display side Terminal block Terminal Terminal Signal name Shield Controller Controller...
Page 113 Digital Controller SIO Driver • 1:1 Connection Terminal Display side Controller resistance Terminal D-Sub 9pin (plug) Terminal block resistance 150Ω ±5% (more than 150Ω ±5% Signal name Signal name Shield (more than 1/2W) 1/2W) LINE(+) LINE(-) Display GND(SG) RS(RTS) Shell •...
Page 114 Digital Controller SIO Driver Cable Diagram 6 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01...
Page 115 Digital Controller SIO Driver • 1:1 Connection Signal name Shield Controller Terminal block Display CA3-ADPCOM-01 Signal name CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Signal name Shield Controller Controller Terminal block Terminal block Shield Display CA3-ADPCOM-01 Signal name...
Page 116 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 Pin (socket) Signal name Shield Controller Terminal block Signal name Display Shell • No termination resistor is required. • 1:n Connection D-Sub 9 Pin (socket) Signal name Shield Controller Controller Terminal block Terminal block Shield Signal name...
Page 117 Digital Controller SIO Driver • 1:1 Connection Signal name Shield Controller Terminal block Display CA4-ADPONL-01 Signal name CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Signal name Shield Controller Controller Terminal block Terminal block Shield Display CA4-ADPONL-01 Signal name...
Page 118 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 Pin (plug) Signal name TERMRX Shield Controller Display Terminal block Signal name CA4-ADPONL-01 TERMTX Shell User-created cable • No termination resistor is required. • 1:n Connection D-Sub 9 Pin (plug) Signal name TERMRX Shield Controller...
Page 119 Digital Controller SIO Driver • 1:1 Connection Controller Terminal block Signal name Signal name Shield Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • No termination resistor is required. • 1:n Connection Controller Controller Terminal block Terminal block Shield Signal name Signal name Signal name Shield Display...
Page 120 Digital Controller SIO Driver • 1:1 Connection Controller D-Sub 9 Pin (socket) Terminal block Signal name Signal name Shield DATA+ DATA- Display GND (SG) Shell • No termination resistor is required. • 1:n Connection Controller Controller D-Sub 9 Pin (socket) Terminal block Terminal block Shield...
Page 121 Digital Controller SIO Driver • 1:1 Connection Display side Terminal block Signal name Shield Controller Terminal block Signal name Display • No termination resistor is required. • 1:n Connection Display side Terminal block Signal name Shield Controller Controller Terminal block Terminal block Shield Signal name...
Page 122 Digital Controller SIO Driver • 1:1 Connection Display side Controller D-Sub 9pin (plug) Terminal block Signal name Signal name Shield LINE(+) Display LINE(-) GND(SG) RS(RTS) Shell • No termination resistor is required. • 1:n Connection Controller Controller Display side Terminal block Terminal block D-Sub 9pin (plug) Shield...
Page 123 Digital Controller SIO Driver Cable Diagram 7 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) AGP-3302B (COM2) Connector terminal block conversion adapter by Pro-face (COM2) CA3-ADPTRM-01 LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Cable length: 500m or less...
Page 124 Digital Controller SIO Driver • 1:1 Connection Connector for the host side communication connection Terminal block Shield Signal name Signal name Display CA3-ADPCOM-01 CA3-ADPTRM-01 User-created cable • 1:n Connection Connector for the host side Connector for the host side Terminal block communication connection communication connection Shield...
Page 125 Digital Controller SIO Driver • 1:1 Connection Connector for the host side D-Sub 9 pin (socket) communication connection Shield Signal name Signal name Display Shell • 1:n Connection Connector for the host side Connector for the host side D-Sub 9 pin (socket) communication connection communication connection Shield...
Page 126 Digital Controller SIO Driver • 1:1 Connection Connector for the host side Terminal block communication connection Shield Signal name Signal name Display CA4-ADPONL-01 CA3-ADPTRM-01 User-created cable • 1:n Connection Connector for the host side Connector for the host side Terminal block communication connection communication connection Shield...
Page 127 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 pin (plug) Connector for the host side Signal name communication connection Shield TERMRX Signal name Display CA4-ADPONL-01 TERMTX Shell User-created cable • 1:n Connection D-Sub 9 pin (plug) Connector for the host side Connector for the host side Signal name communication connection...
Page 128 Digital Controller SIO Driver • 1:1 Connection Display side Connector for the host side Terminal block communication connection Shield Signal name Signal name Display • 1:n Connection Display side Connector for the host side Connector for the host side Terminal block communication connection communication connection Shield...
Page 129 Digital Controller SIO Driver Cable Diagram 8 Display Cable Remarks (Connection Port) COM port conversion adapter by Pro-face. CA3-ADPCOM-01 GP3000 (COM1) Connector terminal block conversion adapter by Pro-face AGP-3302B (COM2) CA3-ADPTRM-01 (COM2) LT (COM1) User-created cable User-created cable Online adapter by Pro-face CA4-ADPONL-01 Connector terminal block conversion adapter by Pro-face CA3-ADPTRM-01...
Page 130 Digital Controller SIO Driver • 1:1 Connection Terminal resistance Terminal block 150Ω ±5% Terminal Signal name Shield Controller (more than resistance 1/2W) Terminal block 150Ω ±5% (more than Signal name Display 1/2W) CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Terminal block resistance...
Page 131 Digital Controller SIO Driver • 1:1 Connection Terminal D-Sub 9 pin (socket) resistance 150Ω ±5% Terminal Signal name Shield Controller (more than resistance Terminal block 1/2W) 150Ω ±5% (more than Signal name 1/2W) Display Shell • 1:n Connection Terminal Terminal D-Sub 9 pin (socket) resistance resistance...
Page 132 Digital Controller SIO Driver • 1:1 Connection Terminal Terminal block resistance 150Ω ±5% Terminal Signal name Shield Controller (more than resistance Terminal block 1/2W) 150Ω ±5% (more than Signal name Display 1/2W) CA4-ADPONL-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Terminal block resistance...
Page 133 Digital Controller SIO Driver • 1:1 Connection D-Sub 9 pin (plug) Terminal resistance Signal name 150Ω ±5% TERMRX Terminal Shield (more than Controller resistance 1/2W) Display Terminal block 150Ω ±5% (more than Signal name 1/2W) CA4-ADPONL-01 TERMTX Shell User-created cable •...
Page 134 Digital Controller SIO Driver • 1:1 Connection Terminal Controller Terminal resistance Shield Terminal block Terminal block resistance 150Ω ±5% 150Ω ±5% (more than Signal name Signal name (more than 1/2W) 1/2W) Display CA3-ADPCOM-01 CA3-ADPTRM-01 TERM User-created cable • 1:n Connection Terminal Controller Controller...
Page 135 Digital Controller SIO Driver • 1:1 Connection Terminal Controller Terminal resistance D-Sub 9 pin (socket) Shield Terminal block resistance 150Ω ±5% 150Ω ±5% Signal name Signal name (more than (more than 1/2W) 1/2W) DATA+ DATA- Display GND(SG) Shell • 1:n Connection Terminal Controller Controller...
Page 136 Digital Controller SIO Driver • 1:1 Connection Display side Terminal block Signal name Terminal Terminal Shield Controller resistance resistance*1 Terminal block 150Ω ±5% (more than Signal name 1/2W) Display • 1:n Connection Display side Terminal block Terminal Signal name Terminal Shield Controller Controller...
Page 137 Digital Controller SIO Driver • 1:1 Connection Terminal Controller Display side Terminal resistance Shield Terminal block resistance D-Sub 9pin (plug) 150Ω ±5% 150Ω ±5% Signal name (more than Signal name (more than 1/2W) 1/2W) LINE(+) LINE(-) Display GND(SG) RS(RTS) Shell •...
Page 138: Supported Devices
Digital Controller SIO Driver Supported Devices The following table shows the range of supported device addresses. Note that the actually supported range varies depending on the External Device to be used. Please check the actual range in your External Device manual. Enter the External Device address in the dialog box below.
Page 139 Digital Controller SIO Driver SDC15/SDC25/SDC26/SDC35/SDC36 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00273.0-31243.F 00273-31243 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 140 Digital Controller SIO Driver SDC20/SDC21 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 0301.0-0690.F 0301-0690 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 141 Digital Controller SIO Driver SDC30/SDC31 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00501.0-06049.F 00501-06049 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 142 Digital Controller SIO Driver SDC40A : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00501.0-06100.F 00501-06100 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 143 Digital Controller SIO Driver SDC40B : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00501.0-08902.F 00501-08902 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 144 Digital Controller SIO Driver SDC40G : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00501.0-06100.F 00501-06100 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 145 Digital Controller SIO Driver SDC45/46 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 1000.0-BFFF.F 1000-BFFF When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 146 Digital Controller SIO Driver DMC10 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 01001.0-07806.F 01001-07806 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 147 Digital Controller SIO Driver 6.10 DMC50 : This address can be specified as system data area. Device Bit Address Word Address 64 bits Remarks 00000001- Data 00000001.00-CF1FFF3A.1F CF1FFF3A When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 148 Digital Controller SIO Driver 6.11 DCP31/DCP32 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00501.0-04600.F 00501-04600 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 149 Digital Controller SIO Driver 6.12 DCP551 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00256.0-01712.F 00256-01712 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 150 Digital Controller SIO Driver 6.13 DCP552 : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00256.0-02003.F 00256-02003 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 151 Digital Controller SIO Driver 6.14 CMC10B : This address can be specified as system data area. Device Bit Address Word Address 32 bits Remarks Data 00401.0-07868.F 00401-07868 When bits are written, the Display reads the corresponding word address from the External Device, sets particular bits of that word address to ON, and then returns the resulting address to the External Device.
Page 152: Device Code And Address Code
Digital Controller SIO Driver Device Code and Address Code Use device code and address code when you select "Device Type & Address" for the address type of the data display or other devices. SDC10 Device Code Device Device Name Address Code (HEX) Data 0080...
Page 153 Digital Controller SIO Driver SDC40G Device Code Device Device Name Address Code (HEX) Data 0080 Word Address SDC45/46 Device Code Device Device Name Address Code (HEX) Data 0080 Word Address DMC10 Device Code Device Device Name Address Code (HEX) Data 0080 Word Address 7.10...
Page 154 Digital Controller SIO Driver Device Code Device Device Name Address Code (HEX) Data 0144 Word Address Data 0145 Word Address Data 0146 Word Address Data 0161 Word Address Data 0162 Word Address Data 0163 Word Address Data 0165 Word Address Data 0166 Word Address...
Page 155 Digital Controller SIO Driver Device Code Device Device Name Address Code (HEX) Data 0C80 Word Address 0C81 0C82 Data ..Word Address 0CE2 0CE3 Data 0D71 Word Address 7.11 DCP31/DCP32 Device Code Device Device Name Address Code (HEX) Data 0080 Word Address 7.12...
Page 156: Error Messages
Digital Controller SIO Driver Error Messages Error messages are displayed on the Display screen as follows: "No.: Device Name: Error Message (Error Occurrence Area)". Each description is shown below. Item Description Error No. Name of the External Device where an error has occurred. Device name is the title of the Device Name External Device set with GP-Pro EX.

Yamatake SDC10 Series Manual

Quick Links

Related Manuals for Yamatake SDC10 Series

Summary of Contents for Yamatake SDC10 Series

This manual is also suitable for: