Matching 569J Model To Evaporator Coil; General - Bryant Legacy Series Installation, Start-Up And Service Instructions Manual

569J*12F only). Copy the unit's Model Number from the
unit's dataplate into the open line in the header above Fig. 1 to
facilitate this step.

Matching 569J Model to Evaporator Coil

The Model 569J***A/B/G/H is a single-circuit unit design, re-
quiring one set of refrigeration piping. This model can be con-
nected to an evaporator coil with one circuit or with two cir-
cuits (by manifolding the evaporator connections into a single
piping system).
The Model 569J***D/E/F is a dual-circuit unit design that re-
quires two sets of refrigeration piping between the outdoor unit
and the evaporator coil (or coils). This model can only be connect-
ed to an evaporator coil that has two refrigeration circuits (or to
two separate evaporator coils). The Model 569J***D/E/F
CANNOT be connected to a single-circuit evaporator coil. The
Model 569J***D/E/F CANNOT be field-converted to a single-
circuit design. See Table 3.
Enter this unit's
Model Number
Position
Example
Model Type
569J = Bryant Condensing Unit
Puron ® R–410A Refrigerant
Voltage
E = 460/3/60
P = 208/ 230/3/60
T = 575/3/60
Nominal Tonnage
07 = 6 Tons
08 = 7.5 Tons
12 = 10 Tons
14 = 12.5 Tons
Refrigerant Circuit
A = Single Circuit
B = Single Circuit with Low Ambient Controller
D = Dual Circuit
E = Dual Circuit with Low Ambient Controller
F = Dual Circuit with Hot Gas Bypass (569J* size 12 only)
G = Single Circuit, Two Stage (569J* size 07 and 08 only)
H = Single Circuit, Two Stage with Low Ambient Controller
(569J* size 07 and 08 only)
Not Used
0 = Not Used
Not Used
0 = Not Used
POSITION NUMBER
TYPICAL
1 2 3 4 5 6 7 8
5 6 9 J E 1 2 F
Fig. 1 — Model Number Nomenclature
1 2
0 5
POSITION
1−2
3−4
5
6−10
Fig. 2 — Serial Number Nomenclature
Table 3 — Evaporator Coil Connections
EVAPORATOR COIL
HAS
Single Circuit
Two Circuits
Before unpacking this new 569J model, compare the evapora-
tor coil design to the 569J model.

General

For unit dimensions see Fig. 3. For corner weights and dimen-
sions see Table 4. For physical data see Tables 5 and 6.
9 10 11 12 13 14 15 16 17
0 0 0 A 0 0 A 0 A
Base Unit Controls
0 = Electro-Mechanical Controls
Electrical Options
A = None
C = Non-Fused Disconnect
Service Options
0 = None
1 = Unpowered Convenience Outlet
2 = Powered Convenience Outlet
Not Used
0 = Not Used
Coil Options
RTPF
A = Al/Cu Standard
B = Pre Coated Al/Cu
C = E-Coated Al/Cu
E = Cu/CuM=Al/Cu Standard with Louvered Hail Guard
N = Pre Coated Al/Cu with Louvered Hail Guard
P = E-Coated Al/Cu with Louvered Hail Guard
R = Cu/Cu with Louvered Hail Guard
Not Used
0 = Not Used
3 4 5
1 5 9
DESIGNATES
Week of manufacture (fiscal calander)
Year of manufacture ("19" = 2019)
Manufacturing location
S e q u e
3
CONNECT TO
MODEL
569J***A/B/G/H
Manifold evaporator
569J***A/B/G/H circuits into single piping
system.
Use two separate piping
569J***D/E/F
systems
Packaging
A = Standard
B = LTL
6 7 8 9
1 2 3 4
n c e n u m b r e
NOTES
—
10
5