Tektronix 7B80 Instruction Manual page 29

CALIBRATION TEST EQUIPMENT REPLACEMENT
Calibration Test Equipment Chart
This chart compares TM 500 product performance to that of older Tektronix equipment. Only those
characteristics where significant specification differences occur, are listed. In some cases the new instrument
may not be a total functional replacement. Additional support instrumentation may be needed or a change in
calibration procedure may be necessary.
Comparison of Main Characteristics
DM 501 replaces 7D13
PG 501 replaces 107
PG 501 - Risetime less than 107
-
Risetime less than
3.5 ns into 50 fl. 3.0 ns into 50
fl.
PG 501
-
5 V output pulse; 108
-
10 V output pulse
3.5
p p
ns Risetime 1 ns Risetime
PG 502 replaces 107
PG 508 replaces 114
115
2101
PG 506 replaces 106
SG 503 replaces 190,
190A. 190B
SG 504 replaces
067-0532-01
067-0650-00
TG 501 replaces 180,
PG 502 - 5 V output
PG 502
-
Risetime less than
1 ns; 10 ns
Pretrigger pulse
108
-
10 V output
11 1
-
Risetime 0.5 ns; 30
to 250 ns
Pretrigger pulse
delav
1
delav
Performance of replacement equipment is the same or
better than equipment being replaced.
PG 506
-
Does not have 0502-01
-
Comparator output
chopped feature. can be alternately
chopped t o a refer-
PG 506
-
G ~ i t i v e - ~ o i n ~
trigger output sig-
nal at least 1 V;
High Amplitude out-
put. 60 V.
SG 503
-
Amplitude range
5 mV t o 5.5 V p-p
106
-
Positive and Negative-
going trigger output
signal, 50 ns and 1 V;
High Amplitude output,
100 V.
190B
-
Amplitude range 40 mV
to 10 V p-p.
SG 503
-
Frequency range 0532-01
-
Frequency range
250 kHz to 250 MHz. 65 MHz to 500 MHz.
-
SG 504
-
Frequency range 0532-01
-
Frequency range
245 MHz to 1050 MHz.
I
65 MHz to 500 MHz.
TG 501
-
Trigger output-
slaved t o marker
output from 5 sec
through 100 ns. One
time-mark can be
generated at a time.
TG 501
-
Trigger output-
slaved to market
output from 5 sec
through 100 ns. One
time-mark can be
generated at a time.
TG 501
-
Trigger output-
slaved tonmarker
output from 5 sec
through 100 ns.
One time-mark can
180A
-
Trigger pulses 1, 10,
100 Hz; 1, 10, and
100 kHz. Multiple
time-marks can be
generated simultan-
eously.
181 - Multiple time-marks
184 - Separate trigger
pulses of 1 and 0.1
sec; 10. 1, and 0.1
ms; 10 and 1 ps.
2901
-
Separate trigger
pulses, from 5 sec
to 0.1 ps. Multiple
time-marks can be
generated simultan-
REV B, JUN 1978
be generated at
a time.
Scans by ArtekMedia O 2006
eously.
NOTE: All TM 500 generator outputs are short-proof. All TM 500 plug-in instruments require TM 500-Series Power Module.