Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Metallkraft SBM 140-12 E
Summary of Contents for Metallkraft SBM 140-12 E
- Page 1 Instruction Manual Bead bending machine SBM 140-12 E SBM 140-12 E...
-
Page 2: Table Of Contents
1.2 Customer service............3 Type of machine Item number 1.3 Limitation of liability ..........3 2 Safety............3 SBM 140-12 E 3814003 2.1 Symbol explanation ..........3 2.2 Requirements to staff ..........4 2.3 Personal protective equipment ......... 4 2.4 Standards and guidelines ......... 5 2.5 General safety regulations........ -
Page 3: Introduction
Introduction Introduction 1.3 Limitation of liability You have made a good choice by purchasing the ME- All information and notes in these operating instructions TALLKRAFT Bead bending machine. were summarised while taking applicable standards and rules, the state-of-the-art technology and our long-term Read the operating manual thoroughly before com- knowledge and experiences into consideration. -
Page 4: Requirements To Staff
Safety Only persons reliable working procedures can be ex- pected from, are allowed to perform all works. Persons CAUTION! the responsiveness of which is affected by e. g. drugs, This combination of symbol and signal words indi- alcohol or medication, are not allowed to work with the cates a potentially dangerous situation which may machine. -
Page 5: Standards And Guidelines
Safety Please note the following: Safety boots 1. Despite the observance of all working instructions, Safety boots protect the feet from being crushed, fall- safety and accident prevention regulations, there re- ing parts and slipping over on slippery ground. mains a residual risk when handling the machine. Th- rough concentrated and forward-looking work and ac- tion, you can reduce the residual risk. -
Page 6: Safety Measures When Dealing With Electricity
Safety Please note the following: 3. Immediately replace deformed and damaged bender rollers. Until the bending rolls are replaced, the use of 1. Do not use the machine if you are unfocused. the machine is prohibited. 2. Operation or maintenance of the machine is prohibited 4. -
Page 7: Safety Measures During Maintenance And Servicing
Intended use 2.9 Safety measures during maintenance and servicing The bead bending machine SBM 140-12 E is an electri- Please note the following: cally operated bending machine. The machine may only be used as described in this manual. The bead bending 1. -
Page 8: Technical Condition
Machine, the CE conformity of the machine may become invalid leave and are the responsibility of the operator. DANGER! Fig. 2: Type plate SBM 140-12 E In the interest of further technical development or 4.3 Scopa of delivery changing regulations, the ma nufacturer reserves the right to make changes to the characteristics of the product at any time without prior notice. -
Page 9: Accessories
Transport, packaging, storage All packaging must be removed; the corresponding in- struction of this installation manual must be read. Pos- sible transport damages are to be photographically do- cumented immediately for the purpose of insurance benefits. To avoid accidents, the necessary precautions must be taken when unloading and transporting the machine. -
Page 10: Packaging
Damage caused by incorrect connections is not covered by the warranty, and The delivery packaging is made of cardboard, so please Metallkraft disclaims any responsibility for conse- dispose carefully by having it chopped up and given to quential damages resulting therefrom. -
Page 11: Description Of The Device
Description of the device Description of the device Illustrations in this operating manual serve the gene- ral understanding and may deviate from the actual design. Fig. 7: Application examples with the E-rollers 7.2 Roller set S1 to S5 3x6 Keyway 3x6 Keyway Fig. -
Page 12: Roller Set S6
Replacing the rollers (Fig.12) 7.3 Roller set S6 7.5 Roller set S8 3x6 Keyway 3x6 Keyway 4 10 3x6 Keyway 3x6 Keyway Fig. 9: Dimensions of the roller set S6 Fig. 11: Dimensions of the roller set S8 7.4 Roller set S7 Replacing the rollers (Fig.12) Step 1: Using the thumbscrew, move the upper drive shaft upwards so that the rollers are free and can... -
Page 13: Working With The Bead Bending Machine
Working with the bead bending machine SBM 140-12 E Working with the bead bending ma- Step 4: Tighten the two nuts after mounting the bending rollers. chine SBM 140-12 E Step 5: Then pull the rollers to center. To do this, open... -
Page 14: Care, Maintenance And Repair
Care, maintenance and repair 10 Care, maintenance and repair DANGER! The bending rolls of the bead bending machine must Tips and recommendations never be lubricated or oiled, as otherwise the mate- To ensure that the bending machine is always in rial could slip through and not be bent. -
Page 15: Disposal, Recycling Of Used Devices
Disposal, recycling of used devices 12.3 Disposal of the old device Fault Possible cause Remedy The Ma- 1.The material 1.Check the mate- Electrical equipment contains a variety of recyclable ma- chine does thickness could rial to be bent. terials and environmentally harmful components. not bend the be wrong. -
Page 16: Disposal Of Lubricants
(5) to the dealer or spare parts de- partment and provide the following information: Type of device: Bead bending machine DANGER! SBM 140-12 E Danger of injury by the use of - Item number: 3814003 wrong spare parts! -
Page 17: Spare Parts Drawing
Spare parts 13.2 Spare parts drawing In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 15: Spare parts drawing SBM-Series | Version 2.04... -
Page 18: Spare Parts List
Spare parts 13.3 Spare parts list Pos. Description Intermediate gear below Pos. Description Screw Machine housing Engine Undercarriage Screw gear cover Shaft stop plate Screw Lower shaft Upper shaft Machine base Intermediate sleeve above Washer Adjusting spring Intermediate sleeve below Foot pedal (without picture.) Ring Fixing nut... -
Page 19: Electrical Schematics
Electrical schematics 14 Electrical schematics Fig. 16: Electrical schematics 1 SBM-Series | Version 2.04... - Page 20 Electrical schematics Fig. 17: Electrical schematics 2 SBM-Series | Version 2.04...
- Page 21 ® Product group: Metallkraft Metal working machines Machine type: Bead bending machine Designation of the machine: SBM 140-12 E Item number: 3814003 Serial number: ____________________ Year of manufacture: 20 ____ due to its design and construction, as well as in the version we have placed on the market, it complies with the relevant basic health and safety requirements of the above-mentioned directive and the following EU directives.
- Page 22 www.metallkraft.de...
Need help?
Do you have a question about the SBM 140-12 E and is the answer not in the manual?
Questions and answers