Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Metallkraft RBM-1305-15E
Summary of Contents for Metallkraft RBM-1305-15E
- Page 1 Operating Instructions Bending Machine RBM 1305-15 E RBM 1305-15 E...
-
Page 2: Table Of Contents
5.2 Packaging............7 Fax: 0 951 96555 - 55 5.3 Storage ............... 7 6 Description of the device............8 E-Mail: info@metallkraft.de 6.1 Scope of delivery..........8 Internet: www.metallkraft.de 6.2 Safety switch............8 7 Installation and connection............8 7.1 Installation............8 7.2 Danger areas............ -
Page 3: Introduction
All information and notes in these operating instructions You have made a good choice by purchasing the were summarised while taking applicable standards METALLKRAFT bending machine. and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration. -
Page 4: Requirements To Staff
Safety alcohol or medication, are not allowed to work with the machine. CAUTION! The qualifications of the personnel for the different tasks This combination of symbol and signal words indi- are mentioned below: cates a potentially dangerous situation which may lead to slight or minor injury if not avoided. -
Page 5: General Safety Regulations
Safety NOTE! Safety boots This device should be grounded in accordance with Safety boots protect the feet from being crushed, national electrical rules and local rules. This must be falling parts and slipping over on slippery ground. done by a qualified electrician. The machine must be earthed to protect the user from electric shock. -
Page 6: Intended Use
Intended use Intended use Technical Data The RBM 1305-15 E round bending machine is used ex- 4.1 Table clusively for the production of round shaped parts such as pipes, cones, cylinders, etc. The material to be bent must not exceed the maximum sheet thickness speci- Technical Data RBM 1305-15 E fied for the machine. -
Page 7: Transport, Packaging, Storage
Transport, packaging, storage Transport, packaging, storage 5.1 Delivery and transport Delivery Check the bending machine on delivery for any visible trans- portation damage. If you notice any damage to the device please report this immediately to the carrier or dealer. Transport Fig. -
Page 8: Description Of The Device
Description of the device Description of the device 6.1 Scope of delivery The scope of delivery of the machine includes: Illustrations in this operating manual serve the general under- standing and may deviate from the actual design. - Driven Top and bottom roller - Wire insert groove on the top and rear roller 6.2 Safety switch For the safety of the operating personnel, the machine is... -
Page 9: Danger Areas
Installation and connection 7.4 Electrical connection NOTE! DANGER! - The Bending Machine is already pre-assembled in Danger to life due to electric current! the delivery condition. There is an immediate danger of electrocution on contact with live components. Setting up the machine - The bending machine may only be connected by electricians. -
Page 10: Operation
Operation Operation Power box The power box contains the controls of the machine and is connected to the pedal. WARNING! Danger due to insufficient qualification of persons! Insufficiently qualified persons can not assess the risks involved in handling the bending machine and expose themselves and others to the risk of serious or fatal injuries. -
Page 11: Work Process
Operation A complete bend with one pass is not possible. To get the desired radius, several passes are required. Tighter NOTE! bends and full radii always require several passes. To be observed before commissioning: In order to be able to remove a bent workpiece from the - The mains voltage must correspond to the voltage machine, the right-hand lock of the upper roller must be specifications on the rating plate. -
Page 12: Bending Process
Operation Calculation of the workpiece length ATTENTION! The unfolded top roller must not be overloaded by the workpiece. The workpiece must be supported by a crane. Step 10: Fold in the top roller and lock. Step 11: Switch off the machine with the main switch. 8.2 Bending process Fig. - Page 13 Operation Calculation of the dimension of the workpiece For finishing pre-banding Top and bottom roll in bring the rear roll upwards straight position Turn sheet metal and posi- For finishing pre-banding tion it for the second pre- bring the rear roll upwards bending Fig.
-
Page 14: Cleaning, Maintenance And Service/Repair
Cleaning, maintenance and service/repair Cleaning, maintenance and service/ NOTE! repair It is important that the roller rotates while you oper- ate the cam lever. When the cam lever is engaged while the rollers are not rotating, a noticeable flat spot or line is formed across the width of the mate- Tips and recommendations rial. -
Page 15: Cleaning And Maintenance
Troubleshooting 9.1 Cleaning and maintenance Interval lubricants Regularly clean the bending machine with a soft, damp bearing, mov- monthly cloth. able parts gears half-yearly grease - The gearbox under the front cover is maintenance- ATTENTION! free and only needs to be checked from time to - Never use solvents to clean plastic parts or painted time. -
Page 16: Disposal, Recycling Of Used Devices
Disposal, recycling of used devices 11 Disposal, recycling of used devices 12.1 Ordering spare parts Please take care in your own interest and in the interest The spare parts may be purchased with the authorized of the environment that all component parts of the ma- dealer or directly with the manufacturer. -
Page 17: Spare Parts Drawing
Spare parts 12.2 Spare parts drawing In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorized dealer. Fig. 16: Spare parts drawing RBM 1305-15 E RBM 1305-15 E | Version 1.02... -
Page 18: Electrical-Schematic
Electrical-schematic 13 Electrical-schematic Fig. 17: Electrical-schematic RBM 1305-15 E RBM 1305-15 E | Version 1.02... -
Page 19: Ec-Declaration Of Conformity
14 EC-Declaration of conformity According to machine directive 2006/42/EC Annex II 1.A Stürmer Maschinen GmbH Manufacturer/retailer: Dr.-Robert-Pfleger-Starße 26 D-96103 Hallstadt herewith declares that the following product ® Metallkraft Metallbearbeitungsmaschinen Product group: RBM 1305-15 E Designation of machine: Bending Machine Machine type: 3781305... - Page 20 www.metallkraft.de...
Need help?
Do you have a question about the RBM-1305-15E and is the answer not in the manual?
Questions and answers