Functional Description; Operation - Makita 6922NB Instruction Manual

smoothly turn, never use it and ask MAKITA
Authorized Service Center for check and repair.
3. When sheared bolt tip falls without moving tip
ejector (tip lever), never use it and ask MAKITA
Authorized Service Center for check and repair.
4. Always be sure you maintain good balance and
firm footing.
Be sure no one is below when using the tool in
high or elevated locations.
5. Hold the tool firmly.
6. Use care and common sense when disposing of
sheared bolt tips. Falling tips from high locations
or scattered tips can cause severe injury.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to shear
wrench safety rules for the subject product. MISUSE
or failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 2)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Removing the outer and inner sleeves
(Fig. 3)
CAUTION:
• Be careful not to allow foreign matter to enter the
insides of the tool when removing or installing the outer
and inner sleeves.
If you need, for your work, different sizes of outer sleeve
and inner sleeve from those installed on your tool, replace
the sleeves as follows.
Loosen the two screws while holding the outer sleeve.
The outer and inner sleeves will be pushed up by the
springs built into the tool.
Press the pin down to remove the inner sleeve from the
outer sleeve. Be careful not to drop the inner sleeve when
removing it. Do not remove the inner sleeve spring, tip rod
and tip rod spring from the tool. (Fig. 4 & 5)
Installing the outer and inner sleeves
Hold the inner sleeve with the pin facing upward. Place
the outer sleeve over the inner sleeve. Press the pin to
allow inserting the inner sleeve, then release the pin to
secure the inner sleeve. (Fig. 6)
Insert the outer and inner sleeves into the tool while
rotating the inner sleeve alternately clockwise and
counterclockwise until there is no gap between the outer
sleeve and the tool. See the figure. Then tighten the two
screws securely. (Fig. 7)

OPERATION

Bolt installation
Slip the tool onto the bolt so that the inner sleeve
completely covers the bolt tip. (Fig. 8)
CAUTION:
• Be careful when fitting the sleeve onto the bolt tip.
Striking the tip can damage it so that it will no longer fit
inside the sleeve properly.
• First tighten bolts preliminarily by using a hand wrench
and then tighten them with this tool. Use this tool only
after preliminary tightening without starting the
tightening with this tool.
Keep forward pressure on the tool while sliding it further
forward until the outer sleeve fits completely over the nut.
If the tool fails to fit completely over the nut, twist the tool
slightly right and left while pushing forward. (Fig. 9)
Pull the switch trigger. The outer sleeve turns to begin
tightening the nut.
When the specified torque is attained, the bolt tip will be
sheared at its notched portion. The bolt tip will remain
inside the inner sleeve. (Fig. 10)
Release the switch trigger and withdraw the tool in a
straight line. (Fig. 11)
CAUTION:
• Do not force the tool down excessively. Apply the
downward force to the degree just needed to hold the
tool firm.
Pull the tip ejector (tip lever) to eject the bolt tip from the
tool. Catch the sheared bolt tips to prevent them from
falling dangerously below. Keep the tips off of the ground,
floor, walkways, etc. to prevent injury from tripping or
falling. (Fig. 12 & 13)
CAUTION:
• Washer and nut have head and tail. Head has
identification mark for nut and chamfer for washer.
When placing them, be careful not to place in reverse.
(Fig. 14)
CAUTION:
• Replace nut, bolt and washer all together at one time
when these rotate together, nut rotates excessively or
a bolt protrude from nut surface too much or less.
• Do not reuse used nut, bolt and washer.
• Choose shear bolts according to the thickness of
workpiece to be fastened. Range for the remaining
length of bolts that are obtained after cutting off chips
are determined by bolt size. Refer to the table below for
details. (Fig. 15)
7