Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tokheim ProGauge MAGLINK LX
Summary of Contents for Tokheim ProGauge MAGLINK LX
- Page 1 CONFIGURATION MANUAL MAGLINK LX Rev. 09 – April 2016...
- Page 2 This page is left intentionally blank.
-
Page 3: Table Of Contents
MAGLINK LX Configuration Manual | Summary UMMARY PREFACE ................................4 GENERAL WARNINGS ............................4 INTRODUCTION ..............................5 LOGIN PROCEDURE ............................7 BASIC FUNCTIONS .............................. 9 CHANGE PASSWORD ............................10 THE "GUEST" AND "ADMIN" PAGES ........................11 ................................11 ISTORY ................................11 LARMS .............................. -
Page 4: Preface
MAGLINK LX Configuration Manual | Preface REFACE Start Italiana S.r.l. has made every effort to keep this document complete, accurate and updated. With every revision of the console, the corresponding information is periodically added to the document. Start Italiana S.r.l. reserves the right to make unannounced improvements and/or changes in the product and/or associated programs. -
Page 5: Introduction
MAGLINK LX Configuration Manual | Login Procedure NTRODUCTION This manual has been prepared in accordance with IEC 82079-1 standards “Preparation of instructions for use - Structuring, content and presentation - Part 1: General principles and detailed requirements” and according to the ATEX Directive 94/9/EU concerning equipment and protective systems intended for use in potentially explosive atmospheres. - Page 6 MAGLINK LX Configuration Manual | Login Procedure The Maglink LX console complies with the requirements of Directive 2012/19/EC on waste of electrical and electronic equipment (WEEE) and hence displaying the according symbol: IMPORTANT: The crossed out wheelie bin symbol indicates that the product must be disposed at the end of its useful life with household waste and must be brought to a collection point for electrical and electronic equipment ATTENTION: The units of measurement contained in this manual refer to a specific choice by...
- Page 7 MAGLINK LX Configuration Manual | Login Procedure OGIN PROCEDURE The following image shows the "Login Page": You can login as a "Guest" user or as an "Admin" user (The user has permission to access configuration pages to obtain common parameters and system parameters relating to the system setup). The following table shows the data displayed depending on the type of log on access: Accessible data Guest...
- Page 8 MAGLINK LX Configuration Manual | Login Procedure By accessing the application as "Admin" user you can perform configuration changes and navigate between pages. The following table shows the default passwords corresponding to the different types of login access: Login access Password Guest GUEST-LX...
-
Page 9: Basic Functions
MAGLINK LX Configuration Manual | Basic Functions ASIC UNCTIONS Once logged in you must enter the application, all pages have the same format. Menu items and user accessibility is displayed in the main menu at the top of the page as shown in the following examples: Log on as "Guest": Main menu Log on as "Admin": Main menu The following items are always present:... -
Page 10: Change Password
MAGLINK LX Configuration Manual | "Guest" and "Admin" pages HANGE ASSWORD The first thing to do is change the password for both "Guest" and "Admin" users. Only the "Admin" user can make password changes. Apply the following procedure: Step Description Login as "Admin"... -
Page 11: The "Guest" And "Admin
MAGLINK LX Configuration Manual | "Guest" and "Admin" pages "G " "A " UEST DMIN PAGES 7.1 History The following image shows the "History Page": The page contains the saved data at regular intervals in a log file for future analysis. You can select from the following filters: •... -
Page 12: Delivery /Losses
MAGLINK LX Configuration Manual | "Guest" and "Admin" pages The page shows alarm history. You can select from the following filters: • Tank • Start date • End Date Pressing the button "View Alarms" displays the data with the configured filters. The alarms are colour coded according to the current state: •... -
Page 13: Current Status
MAGLINK LX Configuration Manual | "Guest" and "Admin" pages 7.4 Current Status The following image shows the "Current Status" page: The page allows you to view all the data sent by the probes connected to the console. The following filters are possible: •... -
Page 14: The "Admin" Page
MAGLINK LX Configuration Manual | "Admin" Pages "A " DMIN PAGE 8.1 System The following image shows the "Systems Page": The page displays system information and parameters applied to all connected probes. The following table lists the parameters that can be set: Parameter Description Total tanks... - Page 15 MAGLINK LX Configuration Manual | "Admin" Pages You can download the PDF of the three manuals regarding the console: Manual • • • User Installation Configuration Fairbanks FTP configuration parameters used to upload data to Fairbanks servers The lower part of the page displays the configuration of the dipswitches. The following table shows the configuration of the dipswitches: Dipswitch Description...
-
Page 16: Tank
MAGLINK LX Configuration Manual | "Admin" Pages 8.2 Tank The following image shows the "Tank Page": The page allows you to set the data of each tank; Select from the drop down "Tank,” for the tank you wish to work on and then set the parameters listed in the following table: Parameter Description When the flag is active, the application queries the corresponding probe during... -
Page 17: Strapping Table
MAGLINK LX Configuration Manual | "Admin" Pages 8.3 Strapping Table The following image shows the "Strapping Table Page": The Strapping table is used to calculate the volume of the tank, given that each tank has its own shape and its own height. After selecting the tank from the "tank"... -
Page 18: Relays
MAGLINK LX Configuration Manual | "Admin" Pages ATTENTION: Press the "Save strapping table" button to apply the changes; Otherwise, the changes are lost. ATTENTION: The strapping table can have a maximum of 500 points The button allows you to download the " Table"... - Page 19 MAGLINK LX Configuration Manual | "Admin" Pages The following image shows the "Sensors" page (Probe type "External Card Start Italiana S.r.l.”): – April 2016 Rev. 09, Page 19 of 28...
-
Page 20: Reconciliation
MAGLINK LX Configuration Manual | "Admin" Pages The following image shows the "Sensors" page ("Triple-state sensor type"): 8.6 Reconciliation The following image shows the "Reconciliation Page": When connected to an FCC (Forecourt Controller) or POS enabled for reconciliation the console receives information on the amount of fuel dispensed. -
Page 21: Shift Report
MAGLINK LX Configuration Manual | "Admin" Pages 8.7 Shift report The following image shows the "Shift report Page": The table shows the start and end of each shift report, select the "Day" and "Tank" values. You can establish an automatic scheduling of the shift report. From the "Time" drop-down list select one of the options then press the "Add schedule"... -
Page 22: Email Configuration
MAGLINK LX Configuration Manual | "Admin" Pages • Gateway ATTENTION: The parameters of the "TCP/IP" page must be modified carefully; The IP address cannot be assigned to another device or computer of the same network 8.10 Email Configuration The following image shows the "Config. email Page": You can send notifications by e-mail. -
Page 23: Modem Configuration Settings
MAGLINK LX Configuration Manual | "Admin" Pages 8.12 Modem configuration settings As option is possible to insert a GSM modem card . It is possible to receive automatic notification or texting an SMS to the modem it will reply with the stock. Phone number configuration for SMS It is possible to select up to 3 telephone numbers to which address the following alert messages: •... -
Page 24: Utility
MAGLINK LX Configuration Manual | "Admin" Pages 8.13 Utility The following image shows the "Utility" page: The following table lists the parameters on the page that can be set: Parameter Description Update date/time of the Change the date/time, paying close attention to the proposed format respecting the locale; Date and time are used console to store data in the console;... -
Page 25: Support
MAGLINK LX User Manual | Revisions UPPORT If you need direct assistance from a Start Italiana S.r.l. technician’s the best solution is to connect the console to the Internet. Configure the router assigning console private IP address to a public IP address of the company, thus opening port 22 for console access and port 80 for web access. -
Page 26: Revisions
MAGLINK LX User Manual | Revisions 10 R EVISIONS The following table lists the revisions to the document: Firmware Revision No. Date Description Revision March 2014 First version 1.0.0 February 2015 Reversing the com port 2.0.0 March 2015 Addition of an application description section 2.0.0 April 2015 Addition of a Certification Section and a Notification Section... - Page 28 START ITALIANA S.r.l. Via Pola 6 20813 Bovisio Masciago (MB) Italia Tel. +39 0362 1581465 Fax +39 0362 1581464 support@startitaliana.it www.startitaliana.it...
Need help?
Do you have a question about the ProGauge MAGLINK LX and is the answer not in the manual?
Questions and answers