Operating The Control Pane; Section 1. Operation Instructions; Basic System Operation; Start-Up And Operation / Before You Start - Waterco Turbotemp 125 Installation And User Manual

OPERATING THE CONTROL PANEL
The Turbotemp 125 Heater controls are as follows:
POOL ON Press this button to govern heater
operation by the pool temperature
setting.
SPA ON Press this button to govern heater
operation by the spa temperature
setting.
HEATER OFF Press this button to switch off the heater.
TEMP Press this button to raise the temperature setting.
TEMP Press this button to lower the temperature setting.
To toggle the display between degrees Celcius (°C) and degrees Fahrenheit (°F):
1. Turn the Operating Control OFF.
2. Press TEMP or TEMP for 5 seconds. The display will ash once and change modes
(°C to °F or vice versa).
3. Turn the Operating Control ON.
When either the TEMP or TEMP buttons are depressed, the digital display will indicate
the temperature setting. After ve seconds, the display will return to the actual pool/spa
temperature.
In addition to the digital temperature display, there are ve indicator lights:
The POOL ON light indicates that the pool water temperature is governing operation of the
heater.
The SPA ON light indicates the spa water temperature is governing operation of the heater.
The HEATING light comes on and stays on when the burner is ring. This light should be on
whenever the burner is on. It blinks when the heater is calling for heat but not ring. If this light
is on but the burner fails to come on, one of the "service" lights should come on, indicating a
fault in the system.
The SERVICE SYSTEM light indicates there is insuf cient water ow to the heater. If the pump
is operating, this usually indicates the lter and/or skimmers should be cleaned (some lters
may require back-washing). If the light remains on after the lter/skimmers have been serviced,
the system should be checked by a quali ed service technician.
The SERVICE HEATER light indicates a fault in the heater or its controls. If this light comes on,
shut down the heater (See "TO TURN OFF GAS TO THE APPLIANCE" on page 2), and have a
quali ed service technician check the system.
!
WARNING
Risk of explosion or fire causing burns or death if safety interlocks are disabled. DO
NOT attempt to operate heater when SERVICE HEATER light is on or if blower or burner will
not start. Instead, follow instructions under "To Switch Off Gas to theAppliance," and call a
quali ed service technician to repair unit.
Turbotemp 125 Pool and Spa Heater Installation and User's Guide
Section 1: Operation Instructions

BASIC SYSTEM OPERATION

Start pump, make sure the pump is running and is primed, to close the water pressure switch
and supply power to heater. Be sure the pool and/or spa is properly lled with water. Follow the
Lighting/Operating instructions below.
HEATER HSI ELECTRONIC IGNITION LIGHTING/OPERATION
FOR YOUR SAFETY: READ BEFORE LIGHTING
!
WARNING
If you do not follow these instructions exactly, a re or explosion may
result causing property damage, personal injury or loss of life.
Do not attempt to light the heater if you suspect a gas leak. Lighting the
heater can result in a re or explosion which can cause personal injury,
death, and.
START-UP AND OPERATION
START-UP AND SHUTDOWN INSTRUCTIONS ARE ON THE LABEL ATTACHED TO THE
COVER OF THE APPLIANCE CONTROL BOX.
BEFORE START-UP
A. This appliance does not have a pilot. It is equipped with an ignition device which automatically
lights the burners. Do not try to light the burners by hand.
B. BEFORE OPERATING, smell all around the appliance area for gas. Be sure to smell next to
the oor because some gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
– Do not try to light any appliance.
– Do not touch any electrical switch; do not use any phone in your building.
– Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
– If you cannot reach your gas supplier, call the Fire Department.
C. Use only your hand to turn the gas control on or off. Never use tools. If you cannot change
the ON/OFF setting by hand, don't try to repair it, call a quali ed service technician. Forced
or attempted repair may result in a re or explosion.
D. Do not use this heater if any part has been under water. Immediately call a quali ed service
technician to inspect the heater and to replace any part of the control system and any gas
control which has been under water.
E. Do not operate the pool heater unless the pool or spa is properly lled with water.
I pg 10