Tire Mobility Kit - Hyundai IONIQ HYBRID Quick Reference Manual

80
10
90
0
min 2.2 bar/ 32 psi
DRIVING
40 50
30 60
70
20
80
10
0 90

TIRE MOBILITY KIT

Setup
1. Remove the speed restriction
label from the sealant bottle and
or
place it on the center of the START
steering wheel.
3
2
1 0
2. Ensure that the compressor is
switched to OFF.
3. Lift the cable cover
the compressor hose
connector of the sealant bottle.
4. Insert the sealant bottle into the
housing slot of the
or compressor. Immediately drive
START
STOP
4-6 miles to evenly distribute the
3
sealant in the tire.
2
1 0
5. Screw the filling hose
50
40
60
30
sealant bottle onto the tire's valve
70
min 2.2 bar/ 32 psi 20
80
stem.
10
90
0
min 2.2 bar/ 32 psi
40 50 6. Insert the compressor power
30 60
70
20 plug into the vehicle's power
80
10
90 outlet.
0
7. Turn the ignition switch to the ON
position or press the Engine Start/
Stop button twice.
Inflate Tire
1. Switch ON the compressor and
let it run for approximately 5
80
max km/h
minutes.
50
max mph
Scan to view a video of: 2. Switch OFF the compressor and
Tire Mobility Kit 80
check to ensure that inflation
max km/h
pressure is over 32 psi. If not, the
50
or
START max mph
puncture is too large to repair.
STOP
3 Contact Hyundai Roadside
2
1 0
Assistance.
3. Remove the filling hose
min 2.2 bar/ 32 psi
compressor hose
compressor power plug
41 I Quick Reference Guide
STOP
50
40
30
20
10
0
min 2.2 bar/ 32 psi
and screw
on to the
NOTE:
A compact spare tire
accessory may be available.
Please consult your nearest
authorized Hyundai dealer.
40 50
30 60
70
20
of the 80
10
90
80 0
max km/h
min 2.2 bar/ 32 psi
50
max mph
50
40
60
30
70
20
80
10
90
0
,
, and
.
HYUNDAI IONIQ HYBRID
IONIQ CUSTOMER DELIVERY CHECKLIST
Recheck Tire Pressure
1. Screw the compressor hose
directly to the tire valve.
2. Insert the compressor power
60
plug into the vehicle's power
70
80
outlet.
90 BEFORE DELIVERY
3. Adjust to the recommended
☐
tire pressure located on the
driver side door jamb placard. ☐
To increase the tire pressure:
1. Switch ON the compressor.
☐
2. To check the current tire
pressure, briefly switch OFF
the compressor.
WALK THE CUSTOMER THROUGH EACH OF
To reduce the tire pressure:
THE FOLLOWING KEY DELIVERY FEATURES
1. Loosen the knob on the
☐
gauge. Tighten the knob to
☐
set tire pressure.
☐
☐
☐
Quick Reference Guide I 42
CUSTOMER NAME DEALERSHIP NAME
SALES CONSULTANT DATE
VIN
SET TIRE PRESSURE LF RF RR LR
VERIFY VEHICLE IS CLEAN, IN GOOD CONDITION,
FREE OF CHIPS AND SCRATCHES · CLEAN WINDSHIELD
AND BACK WINDOW
ENSURE FLOOR MATS ARE SNAPPED INTO PLACE
REVIEW QUICK REFERENCE GUIDE
PAIR CUSTOMER'S PHONE TO THE BLUETOOTH SYSTEM
OPERATION OF THE NAVIAGATION SYSTEM
REVIEW AND TEAR OFF VOICE COMMAND / QUICK TIP CARD
OPERATION OF THE AUDIO SYSTEM
CONNECTING YOUR PHONE
On the radio:
1. Push the SETUP button.
2. Select Bluetooth.
Bluetooth Connection
3. Select .
4. Select Add New.
In your phone's
Bluetooth settings:
5. Select the <Vehicle Name>
on your phone.
6. Enter the passkey from the
radio or accept the authorization
pop-up on your phone.
SWITCHING BETWEEN PAIRED PHONES
Using Voice Command:
"Change Bluetooth device"
On the radio:
1. Push the SETUP button.
2. Select Bluetooth.
3. Select Bluetooth Connection .
4. Select Connect next to the
desired phone.
For more information, visit
HyundaiBluetooth.com