Table of Contents
Advertisement
14 IN. CONCRETE CUT-OFF SAW WALK BEHIND 5.5 HP
ITEM: 61057
OWNER'S MANUAL AND SAFETY INSTRUCTIONS
SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT'S
SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH
AND YEAR OF PURCHASE IF PRODUCT HAS NO NUMBER)
FOR QUESTIONS PLEASE CALL OUR CUSTOMER SUPPORT: (909) 628 4900 MON-FRI 9AM TO 3PM PST
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stark 61057
Summary of Contents for Stark 61057
- Page 1 14 IN. CONCRETE CUT-OFF SAW WALK BEHIND 5.5 HP ITEM: 61057 OWNER’S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S SERIAL NUMBER ON THE BACK OF THE MANUAL NEAR THE ASSEMBLY DIAGRAM (OR MONTH...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. SAFETY The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. -
Page 3: Diamond Blade Safety
IMPORTANT SAFETY INFORMATION ALWAYS read, understand, and follow procedures in operator’s Manual before attempting to operate equipment. ALWAYS be sure to operator is familiar with proper safety precautions and operating techniques before using the cutter. Stop the engine when leaving the cutter unattended. Block the unit when leaving or when using on a slope. -
Page 4: Maintenance Safety
IMPORTANT SAFETY INFORMATION CUTTER TRANSPORTATION SAFETY Use the lifting bail and appropriate lifting equipment to ensure the safe movement of the cutter. DO NOT use the handle bars and/or front pointer as lifting points, NEVER tow the saw behind a vehicle. Ensure that both pointer bars are positioned appropriately to minimize their exposure during transportation. -
Page 5: Product Information
PRODUCT INFORMATION This floor concrete cut saw machine designed specifically for this handheld gas power cutter and for multi- purpose cutting. Its a depth-adjusted cutting machine with super rigid sturdy frame. The construction ensures concrete saw to straight cut. Honda GX 160 engine: 5.5 HP Fits bald size: 12 in. -
Page 6: Installation
INSTALLATION Introduction/Determining the Right Machine The machines used for the primary purpose of “flat” sawing. This type of sawing is described as “flat” because the pavement is cut somewhere close to a horizontal plane. It is the most common type of diamond blade cutting. -
Page 7: Operation
OPERATION NOTE: These starting instructions are general guidelines only. Since many engine options are available, consult the Engine Manual included with this unit for specific instructions. CAUTION: Gasoline Engines: To improve the engine service life, allow the engine to idle without load for (2) to (5) minutes before shutting it down. -
Page 8: Troubleshooting
TROUBLESHOOTING... - Page 9 TROUBLESHOOTING LUBRICATION AND SERVICE Check oil levels, wiring, hoses (air, fuel, water) and lubricate machine daily. Repair or replace all worn or damaged components immediately. Check drive belt tension, do not over-tension. Make sure machine has full set of matched belts. Check blade shaft make sure arbor and threads are not worn damaged or bent.
- Page 10 PARTS LIST - MAJOR COMPONENTS...
- Page 11 PARTS LIST - TRANSMISSION ASSEMBLY...
- Page 12 PARTS LIST - DEPTH ADJUSTING...
- Page 13 PARTS LIST - ENGINE ASSEMBLY...
- Page 14 PARTS LIST - ELECTRIC ASSEMBLY...
-
Page 15: Warranty
WARRANTY PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Need help?
Do you have a question about the 61057 and is the answer not in the manual?
Questions and answers