Trend Micro EdgeFire Quick Setup Manual
  1. Manuals
  2. Brands
  3. Trend Micro Manuals
  4. Network Hardware
  5. EdgeFire
  6. Quick setup manual

Trend Micro EdgeFire Quick Setup Manual

Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
Quick Setup Guide
EdgeFire
EdgeFire
1
1
1
WAN
2
2
2
The EdgeFire is a highly integrated industrial
multiport secure router with firewall / NAT /
VPN / IPS and managed Layer 2 switch
functions. It is designed for
Ethernet-based security applications
providing critical remote control or
monitoring networks, and it provides
an electronic security perimeter
for the protection of critical cyber
assets including
pump-and-treat systems in
water stations, DCS
systems in oil and gas
applications, and
PLC/SCADA
systems in factory
automation.
2
1
Examining the EdgeFire
EdgeFire
1
1
1
WAN
2
2
2
EdgeFire Front Panel
TM
LAN
3
5
7
USB
PWR2 PWR1
STATE IPS/IDS
FAULT VPN
MGMT HA
CONSOLE
4
6
8
DIN rail kit
(Install on the device)
S
ECURED BY
LAN
3
5
7
USB
PWR2 PWR1
RST
STATE IPS/IDS
FAULT VPN
MGMT HA
v+
CONSOLE
IEF-1012-TM
4
6
8
S
ECURED BY
1
RST
PWR1
PWR2
v+
v-
NA
IEF-1012-TM
Verify that the EdgeFire package
contains the following items:
EdgeFire
1
WAN
2
Terminal Blocks x 2
Rubber feet x 4
PWR1
PWR2
v-
NA
EdgeFire Back Panel
1
-
-
Opening and Inspecting
the Package
LAN
1
1
3
5
7
USB
PWR2 PWR1
STATE IPS/IDS
FAULT VPN
MGMT HA
CONSOLE
2
2
4
6
8
EdgeFire Appliance
Console Cable (RJ-45)
Documents
S
ECURED BY
RST
PWR1
PWR2
v+
v-
NA
IEF-1012-TM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EdgeFire and is the answer not in the manual?

Questions and answers

Related Manuals for Trend Micro EdgeFire

Summary of Contents for Trend Micro EdgeFire

  • Page 1 MGMT HA CONSOLE IEF-1012-TM Verify that the EdgeFire package The EdgeFire is a highly integrated industrial contains the following items: multiport secure router with firewall / NAT / VPN / IPS and managed Layer 2 switch functions. It is designed for...
  • Page 2 IEF-1012-TM IEF-1012-TM Production Zone1 Production Zone2 EdgeFire is placed inline (in the direct communication between source and destination device), where it actively analyzes traffic flow, records event logs and takes automated actions to prevent malicious events. Prevention Mode EdgeFire is placed inline (in the direct communication between source and destination device), where it actively analyzes traffic flow and only records event logs without taking action when malicious events are detected.

  • Page 3: Led Indicators

    IPS or IDS enabled IPS/IDS IPS or IDS disabled Green VPN tunnel established No VPN tunnel connected Reset to Factory Default Settings The reset button for the EdgeFire is located on the front panel. EdgeFire ECURED BY PWR1 PWR1 EdgeFire ECURED BY PWR1...
  • Page 4 The aluminum DIN rail attachment plate should already be fixed to the back panel of the EdgeFire when you take it out of the box. If you need to reattach the DIN rail attachment plate to the EdgeFire, make sure the stiff metal spring is oriented towards the back, as shown in the following pictures.

  • Page 5: Wiring The Redundant Power Inputs

    Wiring the Redundant Power Inputs Wiring the Redundant Power Inputs The Trend Micro EdgeFire has two sets of power inputs – power input 1 and power input 2. The top and side views of the terminal block connector are shown below.
  • Page 6 Before connecting the PC/Laptop to the EdgeFire, the PC's IP address should be set to 192.168.127.100. After that, connect the PC to the LAN port of the EdgeFire using an Ethernet cable. Open a web browser on your PC and type “https://192.168.127.254” into the address bar.
  • Page 7 3. In the [Network interface] plane, configure the management IP address for the EdgeFire Connecting to the Network 1. Connect the EdgeFire WAN1 port to a wide area network. (ex: the internet or external network) 2. Connect the EdgeFire LAN1 port to a local area network.
  • Page 8 Both Left / Right LED GE LINK/ACT (Both LED ON = 1 Gbps link, blinking = activity) Appendix: Connecting to the Console Port The EdgeFire console port is an RJ-45 port located on the front panel of the case. It is designed for connection to serial console terminals, for viewing messages during the boot sequence, or for debugging system boot issues.

  • Page 9: Contact Information

    12 to 48 VDC at a Minimum of 2.3 A. © 2020 Trend Micro Incorporated. All Rights Reserved. Trend Micro and the t-ball logo are trademarks or registered trademarks of Trend Micro Incorporated. All other company and/or product names may be trademarks or registered trademarks of their...

Table of Contents