Table of Contents
Advertisement
PSZ2600
5. For safe operation
Remove any obstacle before beginning
work.
4. Inspect the entire unit for loose fasteners
and fuel leakage. Make sure that the cut-
ting attachment is properly installed and
securely fastened.
5. Always use the shoulder strap. Ad-
just the strap for comfort before start-
ing the engine. The strap should be
adjusted so the left hand can com-
fortably hold the handlebar grip ap-
proximately waist high.
STARTING THE ENGINE
1. Keep bystanders and animals at least
15 m away from the operating point.
If you are approached, immediately
stop the engine.
2. The product is equipped with a cen-
trifugal clutch mechanism, so the cut-
ting attachment begins to rotate as
soon as the engine is started by put-
ting the throttle into the start position.
When starting the engine, place the
product onto the ground in a flat clear
area and hold it firmly in place so as
to ensure that neither the cutting part
nor the throttle come into contact with
any obstacle when the engine starts.
Never place the throttle into the high-
speed position when starting the engine.
3. After starting the engine, check to
make sure that the cutting attachment
stops rotating when the throttle is
moved fully back to its original posi-
tion. If it continues to rotate even after
the throttle has been moved fully
back, turn off the engine and take the
unit to your authorized ZENOAH ser-
vicing dealer for repair.
USING THE PRODUCT
Cut only materials recommended by the
manufacturer. And use only for tasks ex-
plained in the manual.
1. Grip the handles firmly with both hands
using your whole hand. Place your feet
slightly apart (slightly further apart than
the width of your shoulders) so that your
weight is distributed evenly across both
legs, and always be sure to maintain a
steady, even posture while working.
2. Maintain the speed of the engine at
the level required to perform cutting
work, and never raise the speed of
the engine above the level necessary.
GB-6
IMPORTANT
WARNING
IMPORTANT
3. Never operate the pruner at an angle
greater than 60° in order to reduce the
risk of being struck by falling objects
during operation.
4. If the unit starts to shake or vibrate,
turn off the engine and check the
whole unit. Do not use it until the
trouble has been properly corrected.
5. Keep all parts of your body away from
rotating cutting attachment and hot
surfaces.
6. Never touch the muffler, spark plug,
or other metallic parts of the engine
while the engine is in operation or
immediately after shutting down the
engine. Doing so could result in seri-
ous burns or electrical shock.
• IF SOMEONE COMES
1. Guard against hazardous situations at
all times. Warn adults to keep pets
and children away from the area. Be
careful if you are approached. Injury
may result from flying debris.
2. If someone calls out or otherwise in-
terrupts you while working, always be
sure to turn off the engine before turn-
ing around.
MAINTENANCE
1. In order to maintain your product in
proper working order, perform the
maintenance and checking opera-
tions described in the manual at regu-
lar intervals.
2. Always be sure to turn off the engine
before performing any maintenance
or checking procedures.
WARNING
The metallic parts reach high temperatures
immediately after stopping the engine.
3. When replacing the cutting attach-
ment or any other part, or when re-
placing the oil or any lubricant, always
be sure to use only ZENOAH prod-
ucts or products which have been
certified by ZENOAH for use with
the ZENOAH product.
4. In the event that any part must be re-
placed or any maintenance or repair
work not described in this manual
must be performed, please contact a
representative from the store nearest
ZENOAH authorized servicing dealer
for assistance.
5. Do not use any accessory or attachment
other than those bearing the ZENOAH
mark and recommended for the unit.
6. Under no circumstances should you
ever take apart the product or alter it
in any way. Doing so might result in
the product becoming damaged dur-
ing operation or the product becom-
ing unable to operate properly.
Advertisement
Table of Contents
