the 12V adapter plug into the vehicle's 12V outlet. If the vehicle's
ignition key has to be on in order for the 12V outlet to supply/receive
power, turn the key without starting the engine.
9. A marine (boat) battery must be removed and charged on shore. To
charge it on board requires equipment specially designed for marine
use.
CHARGER MODES
The charger has nine modes: Standby, 12V NORM, 12V COLD/AGM,
6V NORM, 12V AGM+, 12V LITHIUM, REPAIR, 13.6V SUPPLY and 12V
BOOST CHARGE. Press the CHARGE MODE button to sequence to
desired mode. Press the BOOST CHARGE button to enter 20A charging
mode.
Press and hold the CHARGE MODE button for 3 seconds to enter the
control panel section containing the modes for 12V AGM+, 12V Li-ION,
+ REPAIR and 13.6V SUPPLY. Do not operate the charger until you con-
firm that charger is set to the appropriate charge mode for your battery.
Battery
Mode
Capacity Ah
Standby
_____
12V NORM
50 – 400
15A
12V COLD/
AGM
50 – 400
15A
6V NORM
14 – 150
5A
12V AGM+
15A
50 – 400
BC-15000
Explanation
Not charging or providing any power
Charging 12V WET/GEL/MF/EFB/
batteries (Green 12V LED)
Charging 12V batteries below 50˚ F (10˚
C) or 12 AGM battery (Green 12V LED)
Charging 6V WET/GEL/MF/EFB batteries
(Blue 6V LED)
Charging 12V advanced AGM batteries
that require a higher than normal charg-
ing voltage (Blue 12V LED)
USER'S MANUAL PAGE 6
Mode
Battery
Capacity Ah
12V Li-ION
50 – 400
15A
+ REPAIR
1.5A
50 – 400
13.6V
SUPPLY
_____
10A
12V BOOST
CHARGE 20A
(lead-acid
50 – 400
only)
12V AGM+ (Hold) - This mode is designed for 12V advanced AGM batteries only.
Advanced AGM batteries are typically found in micro-hybrid vehicles. These
batteries accept a higher than normal charging voltage. 12V AGM+ charge is NOT
suitable for traditional AGM batteries. Consult the battery manufacturer before
using this mode.
12V Li-ION – Once at 12V AGM+ tap CHARGE MODE to access
This mode is designed for 12V lithium-ion batteries only, including LiFePO4. Some
lithium-ion batteries may be unstable and unsuitable for charging. Consult the
lithium battery manufacturer instructions before charging for recommended
charging voltage and current.
12V REPAIR – Once at 12V Li-ION tap CHARGE MODE to access
This mode is for LEAD-ACID batteries only. It is an advanced battery recovery
mode for repairing old, idle, stratified or sulfated batteries. NOT all batteries can
be recovered. For optimal results, take the battery through a full charge cycle,
bringing the battery to full charge, before using this mode. One REPAIR cycle can
take up to eight (8) hours to complete the recovery process. This mode uses a
high charging voltage and may cause some water loss in WET cell batteries. Also,
some batteries and electronics may be sensitive to high charging voltages. To
BC-15000
Explanation
Charging 12V Lithium-ion batteries only,
including LiFePO4 (White 12V LED)
Advanced battery recovery mode for
repairing old, idle, stratified or sulfated
batteries. "(Yellow Repair LED and 12V
corresponding charging mode LED)
Converts charger to a DC power supply
for a 12V DC device or as a memory
retainer when replacing a battery (Yellow
SUPPLY LED)
Delivers 20A for 5 minutes to boost
charge a lead-acid battery (solid Red 20A
LED); it has mandatory 5-minute rest for
cooling down (flashing Red 20A LED)
USER'S MANUAL PAGE 7
Need help?
Do you have a question about the BC-15000 and is the answer not in the manual?