Related Manuals for Lincoln Electric POSIMATIC 1E
Summary of Contents for Lincoln Electric POSIMATIC 1E
- Page 1 POSITIONERS POSIMATIC 1E SAFETY INSTRUCTIONS FOR USE AND MAINTENANCE MACHINE No W000315254 8695 6634 EDITION : EN Instructions for use REF: REVISION : Q DATE : 04-2019 Original instructions...
- Page 2 Thank for the trust you have expressed by purchasing this equipment, which will give you full satisfaction if you follow its instructions for use and maintenance. Its design, component specifications and workmanship comply with applicable European directives. Please refer to the enclosed CE declaration to identify the directives applicable to it.
-
Page 3: Table Of Contents
2 - DETAILED DESCRIPTION ....................9 D - ASSEMBLY - INSTALLATION ....................10 E - OPERATOR MANUEL ......................... 11 F - MAINTENANCE ..........................12 1 - SERVICING ......................... 12 2 - SPARE PARTS ........................13 PERSONAL NOTES .......................... 18 POSIMATIC 1E... - Page 4 Spare parts REVISION N 04/16 DESIGNATION PAGE Update C-6 ; E-9 REVISION O 05/17 DESIGNATION PAGE C-4 ; C-5 ; C-7 Update F-12 ; F-13 REVISION P 04/18 DESIGNATION PAGE To change logos REVISION Q 04/19 DESIGNATION PAGE Update POSIMATIC 1E...
-
Page 5: A - Identification
8695 6634 / Q A - IDENTIFICATION Please enter the number of your equipment in the following box. Quote this information in all correspondence. Manufacturing factory code Year manufactured Manufacturing year code Product type Product serial no. POSIMATIC 1E... -
Page 6: B - Safety Instructions
Do not exceed the tilting and rotating torques which determine the maximum admissible load (see diagrams on the equipment). Do not let loads fall hard on the equipment. Fully tighten the workpiece(s) on the positioner table. POSIMATIC 1E... - Page 7 Never modify the machine. The positioner is not designed for anchoring or lifting equipment The use of Personal Protective Equipment (PPE) is mandatory. Clean the working area from time to time. Machine maintenance must be carried out with all the energy supplies switched off. POSIMATIC 1E...
- Page 8 - Make sure that the power and control conductors of the device are in good condition. - Never use the positioner table as a boiler-work table or warm up table without taking basic precautions. - Follow the lubricating instructions, which require the periodic verification of the device, and keep the operations safe. POSIMATIC 1E...
- Page 9 B - SAFETY INSTRUCTIONS 8695 6634 / Q POSIMATIC 1E...
-
Page 10: C - Description
- Irreversible movement; the load cannot in any case drive the table. c) Table - dimensions Ø 300 mm - Ø of shaft passage 28 mm d) Dimensions - height 385 mm - length 397 mm - width 300 mm POSIMATIC 1E... - Page 11 400 A Power Voltage 230 V 400 V Max. consumed intensity 0.4 A 0.2 A Max. power 0.1 KVA Frequency 50/60 Hz Max Off-centre shift : 45 mm See Diagram of tilt torque and Diagram of rotation torque POSIMATIC 1E...
- Page 12 8695 6634 / Q e) Diagram of tilt torque Permitted zone Forbidden zone (vertical table) Load in Kg Distance / table in mm f) Diagram of rotation torque Permitted zone Forbidden zone (vertical table) Load in Kg Off-centre shift in mm POSIMATIC 1E...
-
Page 13: Detailed Description
Also, in order to keep the earth clamp from overheating, users are advised to use welding cables that have a section that is of course compatible with the intensity conducted and its duty ratio. The earth clamp must necessarily be connected in order to prevent damage to the ball bearings of the positioner. POSIMATIC 1E... -
Page 14: D - Assembly - Installation
To change the voltage, move wire no. 6 of the 230 V terminal of the transformer. The main power is connected by means of a three-conductor wire. The customer must use a male connector that is suited to the installation. The pedal is connected to the board at 11 and 12. POSIMATIC 1E D-10... -
Page 15: E - Operator Manuel
The rotation direction of the table can be selected with the help of inverter SA2. The positioner can only be started when SA1 and the pedal P are connected. Potentiometer P1 is used to modify the table speed. POSIMATIC 1E E-11... -
Page 16: F - Maintenance
Regularly check the condition of the surfaces in contact with the earth clamp. Lubrication: BP GR 153 GS - Clean the gear teeth, especially at the back. ESSO SURETT NX 5K - Lubricate the gear teeth with a brush. WYNN’S HPG POSIMATIC 1E F-12... -
Page 17: Spare Parts
Machine interface board W000XXXXXX Flowmeter 9357 XXXX Silk-screen printed front panel For parts order, give the quantity required and put the number of your machine in the box below. TYPE : Number: POSIMATIC 1E F-13... - Page 18 F - MAINTENANCE 8695 6634 / Q POSIMATIC 1E F-14...
- Page 19 160 tooth annular gear W000365911 6009-2RS bearing W000236876 Geared motor with pinion (5 rpm) For parts order, give the quantity required and put the number of your machine in the box below. TYPE : Number: POSIMATIC 1E F-15...
- Page 20 F - MAINTENANCE 8695 6634 / Q POSIMATIC 1E F-16...
- Page 21 Luminous switch W000137811 16 A 250 V black inverter W000137904 Footpedal POSISAF For parts order, give the quantity required and put the number of your machine in the box below. TYPE : Number:: POSIMATIC 1E F-17...
-
Page 22: Personal Notes
F - MAINTENANCE 8695 6634 / Q PERSONAL NOTES Lincoln Electric France S.A.S. Avenue Franklin Roosevelt 76120 Le Grand Quevilly 76121 Le Grand Quevilly cedex www.lincolnelectriceurope.com POSIMATIC 1E F-18...