MTX iT1air Owner's Manual page 4

How To : Connect to the network for Airplay #1 : 5 sec...
1. Connect the iT1air to the wall outlet. Push "Power" to switch on the unit and wait 10 seconds for initialization.
2. Take your iPhone, iPad or iPod Touch and verify it is connected to the Wi-Fi network.
3. Connect your device to the Dock (LED#2 red) or to the USB (LED#2 green).
4. Push once. The unit will display a message on your iDevice asking if you want to share your Wi-Fi settings with the iT1air.
Accept. The iT1air is now available in the Wi-Fi network. The LED#1 will illuminate solid Blue. You can disconnect your device now.
5. Open a computer or you iDevice and in the Airplay devices list, choose "MTX iT1air".
How To : Connect to the network for Airplay #2 : Geek...
1. Connect the iT1air to the wall outlet. Push to switch on the unit and wait 10 seconds for initialization.
2. Press and hold (Wifi control) for 5 seconds. The LED#1 will flash Blue/Purple.
3. Take your computer, your iPad, your iPhone, your iPod touch or any Android tablet and look for the iT1 wifi network.
4. Join the network named "MTX iT1air".
5. Open a web browser and type 192.168.1.1 - You are now on the iT1air setting page (see picture below).
6. Choose your network in the list and type your password.
Note : at the bottom of the Wifi networks list, you can configure it manually, if the network is hidden for example.
7. Hit "Apply". The unit will restart and join the chosen network.
8. Open a computer or your iDevice. In the Airplay devices list, choose the "MTX iT1air". Hit play... Music...
How To : Change "MTX iT1air" in the Airplay list.
You can change the unit wifi name if, for example, you have more than one iT1air in the same network.
1. Connect the iT1air to the wall outlet. Push "Power"
2. Press and hold "Wi-fi" for 5 seconds. The LED#1 will flash Blue/Purple.
3. Take your computer, iPad, iPhone, iPod Touch or any Android tablet and look for the iT1 Wi-Fi network.
4. Join "MTX-iT1air-network".
5. Open a web browser and type 192.168.1.1 - You are now on the iT1air setting page.
6. Type the new desired name in the "AirPlay Device Name field.
7. Hit "Update". The unit will restart. It will be available in the Airplay devices list under the updated name.
How To : Reset the unit.
You can reset the volume and the subwoofer settings.
Press and hold
Press and hold for 5 seconds "Power"
for 5 seconds.
How To : Reset the subwoofer level.
The subwoofer level is adjustable from -5dB to +10dB by 1dB steps.
If you want to go back to 0dB, just push (Sub-) and (Sub+) at the same time on the remote control.
Do not abuse the level of the subwoofers. Too much bass will affect sound quality and add distortion.
Remote
How To : Switch on the Wifi Direct mode.
If no Wifi network is available, the iT1air can generate his own wifi network for Airplay.
Press and hold for 5 seconds the Airplay control (on the Unit or on the Remote) will enable the Wifi Direct mode.
The name of the network (SSID) is « MTX iT1air» . The unit will turn into a router and you'll be able to stream from your
Press and hold
for 5 seconds. Airplay device directly to the unit without any external network.
How To : Install the Batteries in the Remote Control.
Before using the remote control, you must install two AAA batteries.
Remove the bottom panel with a 2mm HEX key. Follow the (+) and (-) signs located around the two springs.
How To : Stay Tuned.
https://www.facebook.com/MTXEurope
https://twitter.com/MTXEurope
http://www.mtxaudio.eu
to switch on the unit and wait 10 seconds for initialization.
on the unit or on the remote control.
AAA
AAA