Main Unit Controls; Led Status Summary - MTX iT1air Owner's Manual

Thank You !
Thank you for purchasing the MTX iT1air high-end, high-definition audio system. The iT1air is designed to deliver a deeper dimension
that brings your music to life. No other system provides the exacting measure of clarity in such a small enclosure. Whether you are
listening from your iPad, iPhone, iPod or computer, the iT1air delivers outstanding sound quality. The iT1air is your new favorite Hi-Fi
system. Congratulations for making a smart choice and enjoy the ultimate audio experience with MTX.
What's In the Box ?
1. The iT1air unit. Use caution when unpacking the unit is heavy.
2. IR remote control. Batteries are not included.
3. Wi-Fi antenna to be connected to the Wi-Fi socket on the back of the unit.
4. Two power cords. One for the European plug (CEE 7/16 Type C and one for the United Kingdom plug (BS 1363 Type G).
5. Owner's manual
Quick Start with Airplay :
1. Connect the iT1air to the wall outlet. Switch on the unit - press "Power"
2. Verify your iPhone, iPad or iPod Touch is connected to the Wi-Fi network you want to join.
3. Connect your device to the Dock (LED#2 red) or to the USB (LED#2 green).
4. Push the Wi-Fi control once. The unit will display a message on your iDevice asking if you want to share your Wi-Fi settings
with the iT1air. Accept. The iT1air is now available in the Wi-Fi network. The LED#1 should be solid Blue. You can now disconnect your
device from the iT1air.
5. Use your computer or iDevice and open "iTunes" or "Music". In the Airplay devices list, choose "MTX iT1air" and hit play to start
listening to music.

LED Status Summary :

iT1air Placement and Installation :
The location of your iT1air in the room is crucial for sound quality and bass level. The unit is equipped with two side subwoofers and
is able to reproduce very low frequencies. Some guidelines should be followed to get the best possible result.
1. Install the unit at an equal distance between the two side walls to get the largest possible staging. The side walls will act as
reflectors.
2. If you reduce the distance between the unit and the back wall, the bass level will rise. If you increase the distance, the bass level
will decrease. Choose distance based on your preference.
3. Your ears and the iT1air should be in the same horizontal plane for perfect definition.
4. To get the best possible result, do not put the unit on a table with a large panel in front of the speakers as it will reflect the sound
in an undesireable way.
5. Adjust the subwoofer level with the remote control.
once - and wait 10 seconds for initialization.
Left - LED#1 :
• Flashing Blue: Looking for the Wi-Fi network
• Solid Blue: Hooked to the Wi-Fi network
• Flashing Red: Remote control feedback
• Flashing Blue/Purple: Wi-Fii setting mode
Right - LED#2 :
• Solid Blue : Airplay input selected
• Solid Red : Dock input selected
• Solid Green : USB input selected
• Solid Purple : AUX input selected

Main Unit Controls

Main Unit Controls
• Single press will power On or power Off the unit. When the unit is Off, the two LEDs willnot be illuminated.
Power On/Off
When the Unit in On, the two LEDs will be illuminated. LED color will depend on the input and settings.
Reset
• Press and hold for 5 seconds to reset the unit's sound settings (volume and subwoofer level to zero).
• Single press will decrease the volume one step - The LED#1 will flash red once.
Volume Down
• Press and hold will decrease volume gradually - The LED#1 will flash red continuously.
• Single press will increase the volume one step - The LED#1 will flash red once.
Volume Up
• Press and hold will increase the volume gradually - The LED#1 will flash red continuously.
• Single press will enable Airplay mode - The LED#2 will turn Blue.
Source : AirPlay
• Press and hold for 5 seconds will enable the Wi-Fi direct mode, the unit will turn into a router and you'll be able to
Direct mode
stream from your Airplay device directly to the unit without any external network.
• First single press will enable dock input - The LED#2 will turn Red
Source Select :
Dock - USB • Second single press will enable USB input - The LED#2 will turn Green
Source Select :
• Single press will enable the jack input - The The LED#2 will turn Purple.
Anologue Jack
• Single press will copy the Wi-Fi settings of your wired device to the unit. The unit will be available on the same
Wi-fi Connection
network as your device.
Settings Mode
• Press and hold for 5 seconds will turn the unit to Wi-Fi settings mode - The LED#1 will flash Blue/Purple. See section
«How To : Connect to the network for Airplay #2» for more details.
LED#1 : Wi-fi Status and Remote Feedback.
When you switch on the unit, the LED#1 will slowly flash blue looking for the Wi-Fi network. It will continue to flash Blue until the network is set.
When the unit is connected to your network, the LED#1 will turn to solid Blue.
When you press any control on the IR remote control, the LED#1 will flash red/blue to indicate that the connection is done.
LED#2 : Input Indicator.
Press for Airplay input - The LED#2 turns blue.
Press for Dock input - The LED#2 will turn red.
Press again for USB input - The LED#2 will turn green.
Press for Jack Aux Analogue input - The LED#2 will turn purple.
Back of the unit