Electrical Connections - PRAXIS AWP 3260 CWH Installation Instructions Manual

Place the unit in the location of installation. Using a 5 or 6 foot level, check
When the unit is to be placed against a wall, blocking should be
Diagram 1
Diagram #1
American Whirlpool Customer Service Department - Telephone - 1-800-327-1394
the highest jet. Run the pump for 15 minutes and check for
leaks. Shut off the pump, let stand for 5 minutes and check
again for leaks. When draining the bath, check tub's base for
proper drainage.
NOTE: The tub must be cleaned before operating the pump.
NEVER OPERATE THE PUMP WITHOUT THE SUCTION
COVER IN PLACE.
After the unit has been tested, close in with the material of
your choice. Seal around the tub lip and surrounding walls
(where applicable) with a water resistant sealer.
Clean out the unit using a damp cloth and liquid detergent.
do not use solvents or abrasive cleaners.

ELECTRICAL CONNECTIONS

Fill tub and test operation.
ALL WIRING MUST BE DONE BY A QUALIFIED, LICENSED ELECTRICIAN
ELECTRICAL CONNECTIONS
ALL WIRING MUST BE DONE BY A QUALIFIED,
LICENSED ELECTRICIAN
BATH PUMP SPECIFICATIONS:
115/120 VAC 6.6 AMP 60 HZ -OR- 115/120 VAC 10.6 AMP
60 HZ, requires a dedicated circuit protected with a 15
AMP GFCI (Ground Fault Circuit Interrupter).
Diagram #3
3
STUD WALL
OUTLET
Diagram 3
GROUNDING
STANDARD ELECTRICAL
LUG
CONNECTION
STUD WALL
OUTLET
DECK INSTALLATION:
Installation Instructions
1-1/2 inches to reach your platform opening dimensions. e.g. Tub dimensions are 60" x 32
Platform opening will be: 58-1/2" x 30-1/2". (See diagram #2)
Hydro-massage Bathtub - UL 1795
See Diagram #3
FAUCET AND VALVES:
For units equipped with luxury upgrades:
sharp hole saw, making sure the spout will clear the deck edge before drilling. A heat resista
material must be placed between the tub and any soldering work to prevent damage to the
115/120 VOLT, 11.2 AMP, 60 HZ. requires a dedicated
circuit protected with a 20 amp GFCI (Ground Fault Circuit
FINISHING: Interrupter)
Before closing in the unit fill the tub 2" above the highest jet. Run the pump
minutes and check for leaks. Shut off the pump, let stand for 5 minutes and check again for
See Diagram #4
When draining the bath, check tub's base for proper drainage.
For all installations, install an outlet to the stud wall a
ELECTRICAL CONNECTIONS
NOTE:
minimum of 6 inches above the floor, located near the
The tub must be cleaned before operating the pump. NEVER OPERATE THE PU
WITHOUT THE SUCTION COVER IN PLACE. ALL WIRING MUST BE DONE BY A QUALIFIED, LICENSED ELECTRICIAN
pump access opening.
BATH PUMP SPECIFICATIONS: 115/120 VAC 6.6 AMP 60 HZ -OR- 115/120 VAC 10.6 AMP 60
HZ, requires a dedicated circuit protected with a 15 AMP GFCI (Ground Fault Circuit Interrupter).
See Diagram #3.
After the unit has been tested, close in with the material of your choice. Seal around the tub
IN-LINE HEATER (OPTIONAL) SPECIFICATIONS:
For units equipped with luxury upgrades: 115/120 VOLT, 11.2 AMP, 60 HZ. requires a dedicated
and surrounding walls (where applicable) with a water resistant sealer.
circuit protected with a 20 amp GFCI (Ground Fault Circuit Interrupter).
1.5 KW, 115/120 VOLT, 12.4 AMP
See Diagram #4.
The In-Line Heater must be connected to a 115/120 VAC,
For all installations, install an outlet to the studwall a minimum of 6 inches above the floor,
located near the pump access opening.
20 AMP, dedicated circuit protected with a GFCI (Ground
Clean out the unit using a damp cloth and liquid detergent. do not use solvents or
IN-LINE HEATER (OPTIONAL) SPECIFICATIONS: 1.5 KW, 115/120 VOLT, 12.4 AMP. The In-
abrasive cleaners.
Fault Circuit Interrupter). Install an outlet to the stud wall.
Line Heater must be connected to a 115/120 VAC, 20 AMP, dedicated circuit protected with a
GFCI (Ground Fault Circuit Interrupter). Install an outlet to the studwall. The outlet must be a
The outlet must be a minimum of 6 inches above the floor
minimum of 6 inches above the floor and must be located near the access panel.
Fill tub and test operation.
and must be located near the access panel.
Note: Where applicable grounding lugs are provided on the exterior of the pump, in-line heater
and control box to permit connection of a No. 8 solid copper bonding conductor between this unit
and all other electrical equipment and exposed metal in the vicinity, as needed to comply with
local requirements.
Note: Where applicable grounding lugs are provided on
the exterior of the pump, in-line heater and control box
to permit connection of a No. 8 solid copper bonding
conductor between this unit and all other electrical
equipment and exposed metal in the vicinity, as needed to
comply with local requirements.
Diagram #3
Diagram #4
AWP 3260 CWH
For deck mounted tubs, use the dimension of the unit and sub
Faucet and valves may be installed through the tub deck. Use
4
STUD WALL
OUTLET
GROUNDING
STANDARD ELECTRICAL
LUG
CONNECTION
STUD WALL
OUTLET
GROUNDING
FOR UNITS EQUIPPED
LUG
WITH LUXURY UPGRADES
5
Diagram 2
Diagram 4