Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Fassi Manuals
  4. Construction Equipment
  5. F 170A.23
  6. Use and maintenance

Fassi F 170A.23 Use And Maintenance

Hide thumbs

Advertisement

Quick Links

Download this manual
FASSI CRANE
F 170A.23
use and maintenance
FROM SERIAL NUMBER
INDEX OF PARAGRAPHS
A0
INTRODUCTION
B0
SAFETY NORMS
C0
WARNING AND INSTRUCTIONS
C0.1
Before operating
C0.2
During operation
C0.3
At the end of the operation (Prior to driving the vehicle)
D0
CLASSIFICATION OF THE CRANE MODEL
D0.1
Technical data
D1
IDENTIFICATION OF THE CRANE MODEL
D1.1
Crane mark
D1.2
Crane mark
E0
CRANE NOMENCLATURE
E0.1
Crane with ground controls and (on request) Crane with ground controls
and with top seat controls by hand cables
E0.2
Crane with top seat controls and with ground controls for outriggers
F0
NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
F0.1
Crane with ground controls and (on request) Crane with ground controls
and with top seat controls by hand cables
F0.2
Crane with top seat controls and with ground controls for outriggers
F1
NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
F1.1
Crane with ground controls and (on request) Crane with ground controls
and with top seat controls by hand cables
F1.2
Crane with top seat controls and with ground controls for outriggers
G0
SUPPLEMENTARY BEAMS
G0.1
Identification of the supplementary beams
G1
TILTABLE OUTRIGGER RAMS
G2
MANOEUVRES AND CONTROLS TO STABILIZE THE VEHICLE
G2.1
Supplementary beam; manual extension of the outrigger supports
G2.2
Functions of control levers for stabilization
G2.3
Controls to stabilize the vehicle
G2.4
Bilateral controls to stabilize the vehicle
H0
CONTROLS TO OPERATE THE CRANE
H0.1
Manoeuvres to unfold the crane into a working condition
H0.2
Manoeuvres to fold the crane into the rest condition
Edition 25.09.2000
3001
*
*
1

Advertisement

loading

Related Manuals for Fassi F 170A.23

Summary of Contents for Fassi F 170A.23

  • Page 1 FASSI CRANE F 170A.23 use and maintenance FROM SERIAL NUMBER 3001 INDEX OF PARAGRAPHS INTRODUCTION SAFETY NORMS WARNING AND INSTRUCTIONS C0.1 Before operating C0.2 During operation C0.3 At the end of the operation (Prior to driving the vehicle) CLASSIFICATION OF THE CRANE MODEL D0.1...
  • Page 2 H0.3 Manoeuvres to unfold the crane "C" into a working condition H0.4 Manoeuvres to fold the crane "C" into the rest condition MANOEUVRES OF THE CRANE LOADS H1.1 Lifting moment limiting device “intelligent type” H1.2 Lifting moment limiting device for two working sectors (optional) H1.3 Control panels H1.4...
  • Page 3 UNI EN ISO 9001 - ISO 9001. The fitment of the crane on the vehicle must be carried out in accordance with the instructions given by FASSI in the manual for hydraulic crane fitting and the relevant chassis manufacturers directives.
  • Page 4 SAFETY NORMS SAFETY NORMS F 170A Strictly conform to the norms reported by the plates DE4236 (fig. 1) placed next to the controls, in order to avoid possible accidents while operating the crane. Only authorized persons are allowed to operate the crane. The crane must be used on firm, level ground.

  • Page 5: Warning And Instructions

    WARNING AND INSTRUCTIONS WARNING AND INSTRUCTIONS F 170A The use of the crane is reserved to authorized personnel, instructed in advance, who has to conform to the safety norms and instructions contained in the use manual supplied with the crane. (See norms ISO 9926-1) It is absolutely prohibited to walk or stop under a suspended load It is prohibited for unauthorized persons to be within the working area.
  • Page 6 Avoid all those situations which may result in crushing during vehicle stabilization, WARNING AND C0.2 INSTRUCTIONS crane movement and load handling. F 170A (In conformity with EN 349 standard the minimum safe working distances to avoid crushing parts of the body) Parts Minimum safe Figure...
  • Page 7 (!) ATTENTION (!) WARNING AND C0.2 INSTRUCTIONS Failure to respect the minimum safe distan- F 170A ces may result in electrical hazards for the operator and his assistants. (!) ATTENTION (!) Do not utilize the crane with wind speed exceeding 12,5 m\s (value 6 of the Beaufort scale).
  • Page 8 Do not rotate the crane before the load WARNING AND C0.3 INSTRUCTIONS is lifted. F 170A Do not operate with sudden move- ments, activate the controls with slow and progressive movements; rotate slowly and with care paying attention to the stability of the vehicle. With ver tical lift, on hydraulic and mechanical extension, rotate slowly in order to avoid side-skidding.

  • Page 9: Technical Data

    CLASSIFICATION OF THE CRANE MODEL CLASSIFICATION OF THE CRANE MODEL F 170A.23 The design of this crane has been carried out in respect of DIN 15018 norms, fatigue test classification H1B3. The crane can operate, intermittently, with lifting devices other than the hook.
  • Page 10 CLASSIFICATION OF D0.1 THE CRANE MODEL F170A.23 F 170A.23 STANDARD 1395 4’ 7’’ 5010 16’ 5’’ 4’ 7’’ EXTRA 1705 5’ 7’’ 5630 18’ 6’’ 2’ 6’’ SUPER-EXTRA 2040 6’ 8’’ 6300 20’ 8’’ 2’ 6’’ — MEZZERIA TIRANTI — FIXING ROD CENTER DISTANCE —...
  • Page 11 THE CRANE MODEL F 170A The exact crane model, serial number and description of implements will enable FASSI Service Department to give a rapid and efficient response. D1.1 Crane mark The CE indicates that the crane complies with the Machines Directive (D.M.) 98/37;...
  • Page 12 CRANE NOMENCLATURE CRANE NOMENCLATURE F 190A E0.1 Crane with ground controls. Crane with ground controls and with top seat controls by hand cables (on request) (fig. 5). Pos. Description Outrigger rams Outrigger supports Base Rotation cylinders Deviator crane - outriggers Dual control for deviator crane - outriggers Multifunction deviator Multifunction transmission...
  • Page 13 CRANE NOMENCLATURE F 170A fig. 5 fig. 6...
  • Page 14 NOMENCLATURE OF THE SAFETY AND NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES PROTECTION DEVICES F 170A F0.1 Crane with ground controls. Crane with ground controls and with top seat controls by hand cables (on request) (fig. 7). Pos. Description Check valves for outrigger rams Check valves for rotation control (flow regulators) Check valve for inner ram Check valve for outer ram...
  • Page 15 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES F 170A fig. 7 fig. 8...
  • Page 16 NOMENCLATURE OF THE SAFETY AND NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES PROTECTION DEVICES F 170A F1.1 Crane with ground controls. Crane with ground controls and with top seat controls by hand cables (on request) (fig. 9). Pos. Description Check valves for outrigger rams Check valves for rotation control (flow regulators) Check valve for inner ram Check valve for outer ram...
  • Page 17 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES F 170A fig. 9 fig. 10...
  • Page 18 SUPPLEMENTARY BEAMS SUPPLEMENTARY BEAMS F 170A Supplementary beams are used in conjunction with the crane outriggers to ensure the vehicle stability during load handling. outrigger ram outrigger extension Weight Code stroke mm interaxis mm type 52185 2132 Fixed 42049 3098 Manual 56681 3558...
  • Page 19 MANOEUVRES AND CONTROLS TO STABILIZE SUPPLEMENTARY BEAMS F 170A THE VEHICLE The outriggers rams prevent damaging stresses both to the frame and to the vehicle suspensions on which the crane is mounted to and assure the stability of the unit during load handling. Be very careful when stabilizing the vehicle;...
  • Page 20 To re-enter the outriggers repeat the operations previously described in reverse. SUPPLEMENTARY BEAMS G2.2 F 170A (!) WARNING (!) Keep hands clear of automatic safety device (lever A from the position of the fig. 14a to the one of the fig. 14). Always make sure that the locking and security devices are correctly locked in position so as to assure the impossibility of accidental movement.
  • Page 21 G2.3 Controls to stabilize the vehicle SUPPLEMENTARY BEAMS G2.3 F 170A The controls conform with the safety directives and enable the operator to activate the lateral extension of the outrigger supports and rams only from the side where he can visually check the operation. - Exit of the outrigger support;...
  • Page 22 CONTROLS TO OPERATE THE CRANE CONTROLS TO OPERATE THE CRANE F 170A (!) WARNING (!) Before operating the crane it is compulsory to set the outriggers. (Plate DE2327 fig. 16) The crane and hydraulic implements can be manually operated with: ground controls on both sides or, on request ground controls on both sides and top seat controls by hand-cables;...
  • Page 23 H0.1 Manoeuvres to unfold the crane into a working condition CONTROLS TO H0.1 OPERATE THE CRANE F 170A - Engage the power take off. - Stabilize the vehicle (see details on Paragraph G2 “Manoeuvres and controls to stabilize the vehicle”). (!) IT IS FORBIDDEN TO OPERATE FROM (!) THE DOUBLE CONTROL SIDE (!) Operate from ground control distributor side (!)
  • Page 24 MANOEUVRES OF THE CRANE LOADS CONTROLS TO OPERATE THE CRANE F 170A Before manoeuvering the load, verify that the working area is suitable for your crane. The lifting curves of the capacity plate indicate the maximum load that the crane can lift at a certain radius and at a certain height.
  • Page 25 Crane with Danfoss distributor (available on request) CONTROLS TO H1.2 OPERATE THE CRANE The lifting moment limiting device system uses the specific functions of the distribu- F 170A tor by utilising an electro-hydraulic technology, it does not allow you exceed the set value, by disactivating the controls (levers in neutral position) commanded by the limiting device.

  • Page 26: Control Panels

    H1.3 Control panels CONTROLS TO H1.3 OPERATE THE CRANE F 170A The electric control panels are placed next to each control station. Layout of the control panel (fig. 19), placed next to the distributor of the crane pos. 1 - Stop button (STOP) 2 - Audible alarm push button (danger) 3 - Orange warning light (90% of the capacity has been reached) 4 - Red warning light (activation of the limiting device)
  • Page 27 After such emergency operations and prior to re-use of the crane, you must immediately go to FASSI authorised Center for testing the structure and re- sealing of the device. Interferences with the valves or removal of the lead seal release the FASSI GRU IDRAULICHE from any responsibility and invalidate the warranty.
  • Page 28 H1.7 Rotation limiting device CONTROLS TO H1.7 OPERATE THE CRANE F 170A When a sector of the working area exists in which the stability is insufficient (for example in the area in front of the cab) the permitted arc of rotation is limi- ted by means of an adjustable electro-hydraulic device which only allows ope- ration within the safe area.
  • Page 29 MANOEUVRES OF THE CRANE LOADS CONTROLS TO OPERATE THE CRANE F 170A Before manoeuvering the load, verify that the working area is suitable for your crane. The lifting curves of the capacity plate indicate the maximum load that the crane can lift at a certain radius and at a certain height.
  • Page 30 H2.2 (optional) CONTROLS TO Lifting moment limiting device “INTELLIGENT TYPE” H2.3 OPERATE THE CRANE F 170A This device utilises an electrohydraulic technology, preventing any movement which causes an increase in the pressure induced by the load in the inner and outer rams of the crane (and of the hydraulic extension if fitted), up to the “critical values”.
  • Page 31 After such emergency operations and prior to re-use of the crane, you must immediately go to FASSI authorised Center for testing the structure and re-sealing of the device. Interferences with the valves or removal of the lead seal release the...
  • Page 32 (!) When using an implement it is always necessary to check that its weight, dimension and capacity is matched to the crane performances. For further information please refer to FASSI GRU IDRAULICHE Warning and norms for crane use also apply for hydraulic implement use.
  • Page 33 MANUAL EXTENSIONS USE OF IMPLEMENTS F 170A These are additional extensions, which are placed in the hydraulic extensions of the crane and of the hydraulic jib and secured by locking pins. Manual extensions have a maximum capacity independent from the crane configuration as shown on the capacity plates.
  • Page 34 WINCH USE OF IMPLEMENTS F 170A The winch is made of a drum that can rotate by means of a hydraulic motor, on a structure fixed on the crane. The rotation of the drum on which the cable winds is achieved by a hydraulic motor controlled by a safety check valve connected to the crane circuit.
  • Page 35 It is recommended to avoid working with the cable hook or the block too USE OF IMPLEMENTS L3.1 close to the pulley structure; the activation of the device could provoque F 170A dangerous swinging. The pulley structure is provided with a group with microswitch (fig. 27) whose lever is kept in position by a balance weight (sliding on the cable);...
  • Page 36 HYDRAULIC JIBS USE OF IMPLEMENTS F 170A The hydraulic jibs, foldable behind the cab, are additional booms, with articulation and with one or more extension booms to be fitted to the last extension boom of the crane; on request the manual extensions can be installed on the extension booms of the jib.
  • Page 37 8. Lifting hook USE OF IMPLEMENTS L4.3 L4.3 Manoeuvres to unfold the jib in working condition F 170A Operate as described to put the crane in working condition (paragraph H0.1). By operating the corresponding levers: - open the outer boom of the jib; - extend the jib outer boom sliding sections;...

  • Page 38: Maintenance Instructions

    Good maintenance and proper use are imperative to maintain efficient use and guarantee the safety of the crane. At least once a year you must take the crane to a Fassi Service Center for a check. (!) Before disconnecting any hydraulic hoses, ensure that there is no pressure in the hydraulic circuit.
  • Page 39 M0.1 At the end of every working day MAINTENANCE M0.1 INSTRUCTIONS F 170A - Check that all safety devices are efficient. - Check the level of the hydraulic oil in the tank. - Check all the components of the hydraulic circuit for possible leaks. - Check that the control and the oil diverter levers can easily be positioned;...
  • Page 40 The following lubricators have been centralized MAINTENANCE M0.3 INSTRUCTIONS and gathered in a case (fig. 34) positioned on F 170A the base (crane distributor side): - rack guide shoe - rotation, - upper and lower bush of the column - column support, - rack group - column gear, - column support group - pendulum beam.
  • Page 41 M0.4 After every 500 working hours MAINTENANCE M0.4 INSTRUCTIONS F 170A Check the tightening torque: - of the fixing rods of the crane; consult the following table in order to find it’s value according to the bolt diameter: Table of the tightening torques of the fixing rods of the crane on the vehicle From “C0404 Kit for crane fixing”.
  • Page 42 MAINTENANCE (!) ATTENZIONE PERICOLO (!) M0.4 INSTRUCTIONS F 170A Sul braccio secondario è installata una bolla a mercurio (interruttore di livello a mercurio) opportunamente incapsulata e protetta e munita di etichetta ade- siva d’avvertimento. IN CASO DI SOSTITUZIONE E/O ROTTAMAZIONE LA CAPSULA CONTE- NENTE MERCURIO VA RICICLATA CON ESTREMA ATTENZIONE E COMUNQUE SECONDO LE NORME NAZIONALI VIGENTI IN QUANTO IL MERCURIO È...
  • Page 43 TABLE OF HYDRAULIC OIL AND LUBRICANTS TABLE OF HYDRAULIC OIL AND LUBRICANTS CHARACTERISTICS CHARACTERISTICS F 170A HYDRAULIC OIL WITH HIGH VISCOSITY: ISO-L-HV Minimal external maximal oil Gradation temperature: temperature: -35°C +45°C ISO VG 32 -20°C +75°C ISO VG 46 HYDRAULIC OIL WEAR RESISTANT: ISO-L-HM Minimal external maximal oil Gradation...

  • Page 44: Possible Faults

    POSSIBLE FAULTS POSSIBLE FAULTS F 170A Many years experience of our product has allowed us to identify and classify the most common faults which occur. In most cases it requires accurate hydraulic and electric troubleshooting and simple rectification. In the following table we report the most frequent inconveniences and our suggested reme- dies.
  • Page 45 P0.2 Operations to be carried out by an authorized POSSIBLE FAULTS P0.2 F 170A service center. FAULTS CAUSE REMEDIES The crane does not lift Non efficiency Replace the pump the loads indicated of the pump on the capacity plate (m ain pressure or auxiliary) Check the pressure, valves not properly adjust the valves...
  • Page 46 INSTRUCTION AND INSTRUCTION AND WARNING PLATES WARNING PLATES F 170A DE 4236 Instruction plate and safety norms DE 2327 Warning plate to stabilize the vehicle before using the crane DE 1684A Do not operate from the double control side, to unfold or fold the crane DE 2497 DE 2498 Warning plates to make sure that no one...
  • Page 47 INSTRUCTION AND WARNING PLATES F 170A DE 1686 Do not walk or stop under a suspended load DE 1683 Do not operate in proximity of electric high- tension lines DE 2361 Do not operate in proximity of electric high- DE2361 tension lines DE 1681 Greasing points with brush...
  • Page 48 HYDRAULIC SCHEMATICS HYDRAULIC SCHEMATICS FOR CRANE FOR CRANE F 170A Hydraulic schematic for crane - HCD4 distributor - ground controls - lifting moment limiting device “intelligent type” CODE DESCRIPTION DV002 DEVIATOR VA187 BLOCK VALVE + FAUCET DV008 DEVIATOR VA194 DOUBLE EFFECT BLOCK VALVE EV104 ELECTROVALVE VA209...
  • Page 49 Hydraulic schematic for crane - HCD4 distributor - top seat controls - lifting moment HYDRAULIC SCHEMATICS FOR CRANE limiting device “intelligent type” F 170A CODE DESCRIPTION DV002 DEVIATOR VA194 DOUBLE EFFECT BLOCK VALVE DV008 DEVIATOR VA209 SIMPLE EFFECT BLOCK VALVE EV104 ELECTROVALVE VA214...
  • Page 50 Hydraulic schematic for crane - Danfoss distributor - lifting moment limiting device HYDRAULIC SCHEMATICS FOR CRANE “intelligent type” F 170A CODE DESCRIPTION DV002 DEVIATOR VA194 DOUBLE EFFECT BLOCK VALVE DV008 DEVIATOR VA209 SIMPLE EFFECT BLOCK VALVE EV109 ELECTROVALVE VA222 OIL FLOW REGULATOR VALVE FOR ROTATION FI870 FILTER CYLINDER...
  • Page 51 Hydraulic schematic for crane - versions: HYDRAULIC SCHEMATICS FOR CRANE 1) n° 2 functions for stabilizers - 2) “C” version F 170A CODE DESCRIPTION DI341 DISTRIBUTOR VA102 DOUBLE EFFECT BLOCK VALVE VA187 BLOCK VALVE + FAUCET VA227 SEQUENCE VALVE...
  • Page 52 HYDRAULIC SCHEMATICS FOR CRANE HYDRAULIC SCHEMATICS FOR CRANE F 170A Hydraulic schematic for crane - HCD4 distributor - ground controls - load limiting device CODE DESCRIPTION DV002 DEVIATOR DV008 DEVIATOR FI870 FILTER RU975 FAUCET VA102 DOUBLE EFFECT BLOCK VALVE VA175 BLOCK VALVE + FAUCET VA187 BLOCK VALVE + FAUCET...
  • Page 53 HYDRAULIC SCHEMATICS Hydraulic schematic for crane - HCD4 distributor - top seat controls FOR CRANE F 170A - load limiting device CODE DESCRIPTION VA233 DOUBLE EFFECT BLOCK VALVE DV002 DEVIATOR DV008 DEVIATOR FI870 FILTER RU975 FAUCET VA102 DOUBLE EFFECT BLOCK VALVE VA175 BLOCK VALVE + FAUCET VA187...
  • Page 54 HYDRAULIC SCHEMATICS FOR CRANE Hydraulic schematic for crane - Danfoss distributor - load limiting device F 170A CODE DESCRIPTION DV002 DEVIATOR DV008 DEVIATOR FI870 FILTER RU975 FAUCET VA102 DOUBLE EFFECT BLOCK VALVE VA175 BLOCK VALVE + FAUCET VA187 BLOCK VALVE + FAUCET VA194 DOUBLE EFFECT BLOCK VALVE VA209...
  • Page 55 ELECTRIC SCHEMATICS FOR CRANE ELECTRIC SCHEMATICS FOR CRANE F 170A Electric schematic for crane - HCD4 distributor - free rotation CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM LAMP TEST DIODE LAMP TEST DIODE POLARITY PROTECTION DIODE EMERGENCY ELECTROVALVE ELECTROVALVE FOR CRANE LIFTING BLOCK ELECTROVALVE FOR CRANE DESCENTS BLOCK PROTECTION FUSE 10 A.
  • Page 56 ELECTRIC SCHEMATICS Electric schematic for crane - HCD4 distributor - limited rotation FOR CRANE F 170A CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM LAMP TEST DIODE LAMP TEST DIODE POLARITY PROTECTION DIODE EMERGENCY ELECTROVALVE ELECTROVALVE FOR CRANE LIFTING BLOCK ELECTROVALVE FOR CRANE DESCENTS BLOCK PROTECTION FUSE 10 A.
  • Page 57 ELECTRIC SCHEMATICS Electric schematic for crane - HCD4 distributor - diversified rotation FOR CRANE F 170A CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM LAMP TEST DIODE LAMP TEST DIODE POLARITY PROTECTION DIODE EMERGENCY ELECTROVALVE ELECTROVALVE FOR CRANE LIFTING BLOCK ELECTROVALVE FOR CRANE DESCENTS BLOCK ELECTROVALVE FOR CRANE LIFTING MOMENT LIMITING DEVICE OF THE TWO WORKING ZONES...
  • Page 58 ELECTRIC SCHEMATICS FOR CRANE Electric schematic for crane - Danfoss distributor - free rotation F 170A CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM BLOCK DELAY CONDENSOR POLARITY PROTECTION DIODE D4/D5 LIFTING MOMENT LIMITING DEVICE DIODES D6/D7 LAMPS TEST DIODES D8/D9 DIODES OR NON RETURN DIODES ELECTROVALVE FOR CRANE LIFTING BLOCK...
  • Page 59 ELECTRIC SCHEMATICS FOR CRANE Electric schematic for crane - Danfoss distributor - limited rotation F 170A CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM BLOCK DELAY CONDENSOR D1/D2 ROTATION CONSENT DIODES POLARITY PROTECTION DIODE D4/D5 LIFTING MOMENT LIMITING DEVICE DIODES D6/D7 LAMPS TEST DIODES D8/D9...
  • Page 60 ELECTRIC SCHEMATICS FOR CRANE Electric schematic for crane - Danfoss distributor - diversified rotation F 170A CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL ACOUSTIC ALARM BLOCK DELAY CONDENSOR D1/D2 ROTATION CONSENT DIODES POLARITY PROTECTION DIODE D4/D5 LIFTING MOMENT LIMITING DEVICE DIODES D6/D7 LAMPS TEST DIODES D8/D9...
  • Page 61 ELECTRIC SCHEMATICS FOR CRANE F 170A Electric schematic for crane - main control panel - HCD4 distributor Electric schematic for crane - satellite for 2°-3° control station - HCD4 distributor...
  • Page 62 ELECTRIC SCHEMATICS FOR CRANE F 170A Electric schematic for crane - main control panel - Danfoss distributor Electric schematic for crane - satellite for 2°-3° control station - Danfoss distributor...
  • Page 63 ELECTRIC SCHEMATICS FOR CRANE ELECTRIC SCHEMATICS FOR CRANE F 170A Electric schematic for crane - Danfoss distributor - free rotation CODE DESCRIPTION ALIM FEED MAIN CONTROL PANEL BLOCK DELAY CONDENSOR POLARITY PROTECTION DIODE ELECTROVALVE FOR CRANE LIFTING BLOCK ELECTROVALVE FOR CRANE DESCENTS BLOCK PROTECTION FUSE 5A PROXIMITY SENSOR VALVE RELAY FOR BLOCK DELAY...
  • Page 64 CAPACITY PLATES FOR CRANE WITH CRANE WITH LIFTING LIFTING MOMENT LIMITING DEVICE MOMENT LIMITING DEVICE F 170A.23 For cranes and manual extensions. For cranes and manual extensions with winch. For hydraulic jib and manual extensions. For hydraulic jib and manual extensions with winch.
  • Page 65 CAPACITY PLATES FOR CRANE WITH LIFTING MOMENT LIMITING DEVICE F 170A.23...
  • Page 66 CAPACITY PLATES FOR CRANE WITH LIFTING MOMENT LIMITING DEVICE F 170A.23...
  • Page 67 CAPACITY PLATES FOR CRANE WITH LIFTING MOMENT LIMITING DEVICE F 170A.23...
  • Page 68 CAPACITY PLATES FOR CRANE WITHOUT LIFTING LIFTING MOMENT LIMITING DEVICE MOMENT LIMITING DEVICE F 170A.23 For cranes and manual extensions. For cranes and manual extensions with winch. For hydraulic jib and manual extensions. For hydraulic jib and manual extensions with winch.
  • Page 69 CAPACITY PLATES FOR CRANE WITHOUT LIFTING MOMENT LIMITING DEVICE F 170A.23...
  • Page 70 CAPACITY PLATES FOR CRANE WITHOUT LIFTING MOMENT LIMITING DEVICE F 170A.23...