Advertisement
SPECIFICATION AND INSTALLATION GUIDE
FCR2
Field Cut Riser System
For use with grease interceptor models GB-50, GB-75, GB-250, GB-500,
GB-1000, GGI-500, GGI-750, GGI-1000, GGI-1500 and GGI-2000; solids
interceptor models SI-50, SI-75, SI-250 and SI-500; sampling port models
SV24 and SV24-O; and wastewater flow distributor FS-DUO
Contents
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Special Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Getting to Know the FCR2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
FCR2 Compatible Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Notes
1.
Unit weight: 32 lbs.
2. Riser not designed to hold water
Engineer Specification Guide:
Field-cut adjustable riser system to consist of injection molded polypropylene
body, 100% Silicone Sealant for assembly of riser components, butyl mastic sealant
for tank-riser or riser-riser joints, stainless steel fastening hardware and heavy duty
nylon cable ties and mounts. Riser shall allow field adjustability of cover to grade.
Installation Note
Minimum install height: 4". Maximum install height: 34". Riser system may be
stacked no more than three units high to a maximum of 94" extension. Access to
internal components will not be compromised.
9500 Woodend Road | Edwardsville, KS 66111 | 913-951-3300 | schierproducts.com
MODEL NUMBER:
FCR2
PART #: 8010-006-01
DWG BY: B. Karrer
TOP VIEW
SIDE VIEW
1" TYP
Cut
Lines
SECTION A-A
1"
Riser Height Needed
0" - 4"
>4" - 34"
>34" - 64"
>64" - 94"
DESCRIPTION: 34" Field Cut Riser System
DATE: 6/24/2020
REV:
A
6" TYP
A
ø 27-1/2"
ø 23"
32-1/2"
ø 24-3/16"
Risers Required
(per accessway)
None (use adapter)
FCR2
FCR2 (x2)
FCR2 (x3)
ECO:
© Copyright 2020 Schier, All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Schier FCR2
Summary of Contents for Schier FCR2
-
Page 1: Table Of Contents
FCR2 Compatible Models ........ -
Page 2: Special Precautions
SPECIAL PRECAUTIONS For Schier riser Installations - Failure to follow this guidance voids your warranty DO NOT AIR TEST UNIT OR RISER SYSTEM! Do not install this unit in any manner Doing so may result in property damage, personal injury or death. - Page 3 SPECIAL PRECAUTIONS For Schier riser Installations - Failure to follow this guidance voids your warranty ODOR ALERT! High Temperature Kitchen Water Interceptor is not a sewer gas trap. cold water supply line All upstream fixtures high temperature must be trapped effluent ( >...
-
Page 4: Getting To Know The Fcr2
GETTING TO KNOW THE FCR2 #8 x 5/8" riser body assembly screw (x12) 5. Cable tie mounts(x4) 2. Riser body half (x2) 6. Heavy duty 18" - 120 lb. cable tie (x4) 3. 100% silicone sealant 7. Stainless steel eyebolt and nut (x4) 4. -
Page 5: Installation
>64" - 94" FCR2 (x3) Determine trim length (round up all fractions to next inch). Measuring from bottom Only one FCR2 riser per cover will need to be cut. of riser, mark trim length and cut riser halves. Riser Height... - Page 6 Groove Edge another bead into the sealant trough next to the screw holes. Sealant Trough Groove Immediately assemble riser halves after applying sealant and fasten using supplied screws. page 6 of 10 Schier | FCR2 Installation Guide...
- Page 7 Tighten cable ties, a little bit at a time in a star pattern going around the riser to evenly force the riser into the mastic sealant. Riser should go 1/2" - 3/4" into the sealant. Schier | FCR2 Installation Guide page 7 of 10...
- Page 8 Make final adjustments to do not tighten. riser into the mastic sealant. riser should go 1/2" - cable ties to ensure riser 3/4" into the sealant. system is level. page 8 of 10 Schier | FCR2 Installation Guide...
- Page 9 Cover Adapter bit. If required, cover adapters may now be tilted up to 10º in any direction using Gasket gasket flexibility. Upper Band Clamp Lower Band Clamp 2" minimum Top Level Riser Schier | FCR2 Installation Guide page 9 of 10...
-
Page 10: Fcr2 Compatible Models
Gravity Grease Interceptors GGI-500 GGI-750 GGI-1000 GGI-1500 GGI-2000 Billy Goat ™ Kitchen Solids Interceptors SI-50 SI-75 SI-250 SI-500 Sewer Viewer Flow Splitter ™ ™ Wastewater Sampling Ports Wastwater Flow Distributors SV24 SV24-O FS-DUO page 10 of 10 Schier | FCR2 Installation Guide...
Need help?
Do you have a question about the FCR2 and is the answer not in the manual?
Questions and answers