Table of Contents
Advertisement
Quick Links
HEADSET TO MULTI-BASE STATION
WHAT IS HEADSET TO MULTI-BASE STATION?
In normal operation, a headset may only pair with a single Base Station. The Headset to Multi-Base
Station feature allows a user to pair a 505 or 507 DECT7 Wireless Headset with up to four WB505R
DECT7 Wireless Base Stations.
REQUIRED EQUIPMENT
•
A 505 or 507 DECT7 Wireless Headset with Firmware Application 13 or later.
•
A minimum of two (2) and a maximum of four (4) WB505R DECT7 Wireless Base Stations.
OPERATING MODES
Operating modes control how the Headset reconnects when paired with multiple Base Stations.
Manual Mode is recommended for most situations. In this mode, the user selects a specific Base
Station number to reconnect with using Headset buttons.
Auto Mode allows the Headset to automatically reconnect with the nearest paired Base Station after
it has disconnected from its current Base Station. In Auto Mode, each Base Station should be placed
so that its radio frequency footprint, or wireless coverage area, does not overlap with any other Base
Station to which one or more Headset to Multi-Base Station users are paired.
For more information, see
Appendix A: Auto Mode Configuration and
USER GUIDE
Use.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Sonetics Firecom 505 DECT7
Summary of Contents for Sonetics Firecom 505 DECT7
- Page 1 USER GUIDE HEADSET TO MULTI-BASE STATION WHAT IS HEADSET TO MULTI-BASE STATION? In normal operation, a headset may only pair with a single Base Station. The Headset to Multi-Base Station feature allows a user to pair a 505 or 507 DECT7 Wireless Headset with up to four WB505R DECT7 Wireless Base Stations.
- Page 2 Before enabling the Headset to Multi-Base Station feature, ensure that the 505 or 507 DECT7 Wireless Headset has the most recent firmware revision installed. Check for the current firmware version using the Sonetics Configuration Utility software. (Download your copy at: https://www.firecom.com/...
- Page 3 BEFORE YOU BEGIN: CLEAR ALL PAIRINGS ON THE HEADSET Place the headset into Pairing Mode by holding down the RIGHT PTT and the POWER buttons together, and listen for a voice prompt to announce “Base Station registering.” Release both buttons. Power OFF the headset.
- Page 4 ENABLING AND CONFIGURING THE HEADSET TO MULTI-BASE STATION FEATURE To enable and configure the Headset to Multi-Base Station feature, access the Advanced Menu on your headset: Turn OFF the headset. Press and hold the POWER , FWD and BACK buttons until the voice prompt announces “Advanced Menu.”...
- Page 5 SELECTING A BASE STATION IN MANUAL MODE Begin by selecting a Base Station to connect to: Press both the MINUS and BACK buttons simultaneously to enter Base Station selection mode. Use the PLUS and MINUS buttons to select the Base Station you wish to connect to (Voice prompts will announce “Base Station 1”, “Base Station 2”...
- Page 6 As you set-up and configure the Headset to Multi-Base Station feature for use in Auto Mode, please contact Firecom Support at (888) 561-8098 for detailed instructions and configuration advice. SELECTING AUTO MODE Auto Mode is only available when configured using the Sonetics Configuration Utility Software (see Appendix B: Using the Sonetics Configuration Utility Software for Set-Up).
- Page 7 Feature Adv. Menu Start-Up Quick Launch Options Menu Defaults Enable Setting vice To enable and configure the Headset to Multi-Base Station feature using the Sonetics Configuration Volume Current Vol 1 Vol 2 Vol 3 Vol 4 Enable Setting Utility software, do the following:...
- Page 8 On, Battery high/med/low” to be heard. Repeat Steps. Once the headset has been paired to all Base Stations, reconnect the headset to the computer using the Mini USB connector, and launch the Sonetics Configuration Utility. Click the “Find Device” button. Click the “Customize Device” button.
Need help?
Do you have a question about the Firecom 505 DECT7 and is the answer not in the manual?
Questions and answers