DeWalt XR LI-ION DCF888 Instructions Manual page 36

EnGLIsh
NOTICE: Always check the tool configuration prior to use.
If you are unsure of the current configuration, press the
mode selector button 11
Home setting as described on the label and this manual.
This tool is capable of connecting with mobile devices that
support Bluetooth® Smart (or Bluetooth® 4.0) technology.
(To see if your mobile device is compatible, visit: http://www.
bluetooth.com/Pages/Bluetooth-Smart-Devices-List.aspx)
D WALT Tool Connect™ is an optional application for your
e
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific tool
functions. Refer to Mode Selector.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D WALT Tool Connect™ application at:
e
• Install a fully charged 18V battery pack into the tool. Refer to
Inserting and Removing the Battery Pack from the Tool.
• Follow the instructions in the app to create your Tool
Connect™ account.
• On the Home screen of the app, select "+ Tool" to begin the
process of adding your tool to the app.
• To connect your tool with the D
app, at the appropriate screen, press the mode selector
button 11 for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at a time.
• Once the tool has been connected, you can confirm that
you would like to register the product.
Coin Cell Battery
Bluetooth® capability is powered by one coin cell battery in
your tool, that when necessary, should be replaced by your local
D WALT service center. Do not attempt to replace the coin cell
e
battery yourself.

WARNING: Danger of explosion if battery is
incorrectly replaced.
TaBLE 1
Customizable Features
Worklight brightness
Worklight delay off
Maximum speed (RPM)
Precision Drive hesitation (seconds)
34
(Fig. D) to set the tool to the
WALT Tool Connect™
e
Home Mode 1
High High
20 secs 20 secs
3250 1000
Disabled

WARNING: DO NOT INGEST BATTERY; CHEMICAL
BURN HAZARD. This product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead
to death.
• Keep new and used batteries away from children. If
the battery compartment does not close securely, stop
using the product and keep it away from children.
• If you think batteries might have been swallowed or
placed inside any part of the body, seek immediate
medical attention.
• If the coin cell battery contents come into contact
with the skin, immediately wash area with mild soap
and water. If coin cell battery liquid gets into the eye,
rinse water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of an organic solvent
and lithium salts.
• Do not incinerate or dispose of tool together with
household waste material! Tool that has reached
the end of its life must be collected separately
and returned to an environmentally compatible
recycling facility.
OPERATION

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury. Exception—Tool Connect™
functions and mode adjustments require battery to
be installed.
NOTICE: Always check the tool configuration prior to
use. If you are unsure of the current configuration, press
the mode button 11
setting as described on the label and this manual.
Proper Hand Position (Fig. E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle .
10
Factory Presets
Mode 2
High
20 secs
2800
1 Disabled
(Fig. D) to set the tool to the Home
Mode 3 Customizable Range
High OFF–High
20 secs 0–20 minutes
3250 1000–3250
Disabled 0–1